Aloha from Hawaii love your content. Can you make a video of how to properly tune your carburetor? Moped shopes here in Hawaii are ours away from where I live and it would be very helpful and convenient if you could show us how to properly tune the carburetor. I have 150cc gy6
I have a couple of videos on how to fine tune the GY6 Carb. via moving the metering rod needle clip and changing the jet sizes. This takes time and patience
I have a couple of videos on how to fine tune the GY6 Carb. via moving the metering rod needle clip and changing the jet sizes. This takes time and patience
My scooter cuts out completely if you turn the throttle at all. It takes about 2 minutes of it bogging out like that before it will let me rev it like normal and ride. It seems to only do this in cold weather. Once the scooter is warmed up it rides and runs greats! Any thoughts please?
I would love to be able to call and ask questions. i don’t know where to change my oil or how to maintain my 49cc Vitacci 2022 i’m trying to follow your videos i can’t find my scooter
Do all these suggestions work for a 300CC fuel injected Chinese scooter? Mine bogs down and turns off when you enthusiastically give it gas. Gentle rolling off from a stop doesnt cause this issue. Also, the scooter doesnt accelerate past 57kmph unless you twist it to the max, then it acts like a supercharger and boosts itself forward. I have ordered a throttle position sensor for the dodgy acceleration and I hope that sorts it out. Dont know what to do about the bogging
Hi please can you help me. I have a wangye eivessa 2 125cc year of the bike 2022 it has done 2215 miles i bought it second hand and had a months warranty which has run out. When the bike is ticking over I have a mass of blue smoke coming out of the exhaust and the bike cuts out due to excess of smoke. The carborrettor is an EFI. At present I have not messed about with it. Is it possible I have a leak on the carburetor or is it a case of piston and rings need replacing along with the valves and seals. I have ordered a compression test kit and will do a test. Please can you give me some advice if it is possible the the carburetor mixture or a hose leak within the engine bay. Cheers
@@ScooterATVSales I don't have a dealer in my local area to have the bike serviced. I'm not sure if its piston and rings along with valves and seals need replacing as its seems to be burning oil. I'm not sure if their is a leak in and around the engine. I have ordered a compression test kit which should hopefully eliminate the engine as mentioned. You have a smashing channel keep posting videos. Cheers
is there a reason why my scooter can't go slowly, it wants to do wheelie with a light throttle and then it goes normally with light throtle, I want it to go slowly not to do a wheelie I almost fell more than once I tried to replace the spring,weights, the situation only gets worse
I put a brand new carburetor on my 150cc scooter and it started to bogged down when accelerating after putting the new carburetor. I don’t know why it started doing it after putting a brand new carburetor
@@ScooterATVSales I found the solution i put the old carburetor back and it doesn’t bogged down anymore. It looks like it was the new carburetor came defective when i bought it
Of first of all it’s not a pressure regulator and it’s definitely not called a petcock. It’s a diaphragm full pump that works off engine vacuum .just to set the record straight.a petcock turns the fuel off and on . And a presser pressure regulator regulates the pressure in a system usually in a fuel injection system with an electric pump but some mechanical pumps do have a regulator. Not trolling just wanted to say that so your viewers don’t get it wrong when they go to purchase parts.
Thank you for your video.
2020 ice bear vision 150cc I put a cone air filter and it restricted air flow making it bog at high throttle. 60mph top speed.
Aloha from Hawaii love your content. Can you make a video of how to properly tune your carburetor? Moped shopes here in Hawaii are ours away from where I live and it would be very helpful and convenient if you could show us how to properly tune the carburetor. I have 150cc gy6
I have a couple of videos on how to fine tune the GY6 Carb. via moving the metering rod needle clip and changing the jet sizes. This takes time and patience
I have a couple of videos on how to fine tune the GY6 Carb. via moving the metering rod needle clip and changing the jet sizes. This takes time and patience
i was riding my moped and when i full throttle after a couple of minutes the speed starts decreasing on its own without braking
The video tips will help with isolating the problem.
My scooter cuts out completely if you turn the throttle at all. It takes about 2 minutes of it bogging out like that before it will let me rev it like normal and ride. It seems to only do this in cold weather. Once the scooter is warmed up it rides and runs greats! Any thoughts please?
Also it is very hard to start when cold. 50cc Chinese scooter
Check the vacuum lines, the intake manifold for any defects and the intakes base gasket.
I would love to be able to call and ask questions. i don’t know where to change my oil or how to maintain my 49cc Vitacci 2022 i’m trying to follow your videos i can’t find my scooter
The fundamentals are the same on all QMB139 49cc service. We have a lot of videos. Check our playlist
what should i do my 50cc gives gas on its own
Good job!
Thank you
Do all these suggestions work for a 300CC fuel injected Chinese scooter?
Mine bogs down and turns off when you enthusiastically give it gas.
Gentle rolling off from a stop doesnt cause this issue.
Also, the scooter doesnt accelerate past 57kmph unless you twist it to the max, then it acts like a supercharger and boosts itself forward.
I have ordered a throttle position sensor for the dodgy acceleration and I hope that sorts it out. Dont know what to do about the bogging
Generally they do.
Hi please can you help me.
I have a wangye eivessa 2 125cc year of the bike 2022 it has done 2215 miles i bought it second hand and had a months warranty which has run out.
When the bike is ticking over I have a mass of blue smoke coming out of the exhaust and the bike cuts out due to excess of smoke.
The carborrettor is an EFI. At present I have not messed about with it.
Is it possible I have a leak on the carburetor or is it a case of piston and rings need replacing along with the valves and seals.
I have ordered a compression test kit and will do a test.
Please can you give me some advice if it is possible the the carburetor mixture or a hose leak within the engine bay.
Cheers
I am not familiar with that brand or model. Please contact your local dealer or manufacture.
@@ScooterATVSales I don't have a dealer in my local area to have the bike serviced.
I'm not sure if its piston and rings along with valves and seals need replacing as its seems to be burning oil.
I'm not sure if their is a leak in and around the engine. I have ordered a compression test kit which should hopefully eliminate the engine as mentioned.
You have a smashing channel keep posting videos.
Cheers
You did not say whether to put clip higher or lower to remove bogging
Can you make a video on how to change the mirrors on a bahama vip? I have to replace mines. I broke them😂🤷♀️
Just unscrew them if you can’t find the screw lift up the covers
@@zynk1x881 But how do I know what size it is so I can get a replacement?
Google the bolt size or measure it with a ruler or tape measure, calipers if you have them do best
I want scooter to buy from Ghana can you help ?
You may want to contact the manufacturer direct. Tao Motors USA
I had this problem with a Chinese 50cc moped and it was just the 3way fuel valve £7 fix
Glad we can help
is there a reason why my scooter can't go slowly, it wants to do wheelie with a light throttle and then it goes normally with light throtle, I want it to go slowly not to do a wheelie I almost fell more than once I tried to replace the spring,weights, the situation only gets worse
Just be easy on the throttle
@@ScooterATVSales nah the trottle is not the problem it started doing that recentli
I put a brand new carburetor on my 150cc scooter and it started to bogged down when accelerating after putting the new carburetor. I don’t know why it started doing it after putting a brand new carburetor
Check the vacuum lines, intake manifold for leaks.
@@ScooterATVSales I found the solution i put the old carburetor back and it doesn’t bogged down anymore. It looks like it was the new carburetor came defective when i bought it
@@ScooterATVSales also one more question my scooter battery is completely dead does the battery charges while riding the scooter
@@Cristopher180- Yes
Of first of all it’s not a pressure regulator and it’s definitely not called a petcock. It’s a diaphragm full pump that works off engine vacuum .just to set the record straight.a petcock turns the fuel off and on . And a presser pressure regulator regulates the pressure in a system usually in a fuel injection system with an electric pump but some mechanical pumps do have a regulator. Not trolling just wanted to say that so your viewers don’t get it wrong when they go to purchase parts.
Appreciate the feedback
2020 ice bear vision 150cc I put a cone air filter and it restricted air flow making it bog at high throttle. 60mph top speed.