🚨 P16 is cruise control. I think it’s a dangerous setting to have, so leave it be. ⚡️ Must watch Kirin M4 Pro playlist ruclips.net/p/PLOIER5h7JLytR_Q-_9ZjMB9hidFy3S_qo 🛴 Official KUGOO site and latest discounts (automatically applied) bit.ly/47guuEZ
Xiaomi/Kugoo and most scooters don’t have good water resistance. But you can definitely improve it yourself for any scooter. This is the video from last week about water resistance improvement ruclips.net/video/ZSFcnzdgKp0/видео.html
I ordered one of these a few weeks ago it came within a couple of days but I've only just got round to unpacking and setting it up, just a quick heads up to anyone who's waiting for delivery of one of these scooters, the instructions on how to unfold it a very vague I was getting extremely pissed off with working out how to lock the stem in place(it doesn't tell you in the instructions), I had to look on RUclips for a vid, turns out you have to give the stem a Wright good shunt forward to snap it place, before I knew this I was trying to do it for ages and getting extremely annoyed, all good now.
Finally a quick, simple and well explained video on the kugoo settings! I have the ienyrid m4 pro which is basically the same scooter under a different name. Has the same controller and everything so everything in this video applies to me too. Thanks for this video buddy it’s helped me a lot and it’s easy to follow 👍🏻👍🏻
@@MovelectricsJust a question, I bought a Kugoo Kirin M4 and recently I bought a Kugoo Kirin G2 max, do the settings work the same for those 2 scooters or it is something diffrent? Thanks
I actually modified P6 and set it to 8.4 instead of 10 so i could get a more accurate speed reading on my scooter. The only actual way of getting more speed is to get tires with a larger diameter which requires quite a few modifications to allow for those larger tires to fit.
Most scooters I’ve had never have accurate speed readings from the display. Sometimes they are off by only a few kms. I always leave it it the default p settings for wheel diameter/magnets etc. I always test with a GPS app.
@@Until_It_Is_Done the meter is off accuracy by 1" on mine. It's different for everyone's scooter though. Also the original tire was slightly smaller than 10 inches, which I had replaced recently along with the motor.
After comparing to my GPS and my mountain bike speedometer, the best setting for P06 is 9.1 for the most accurate speed. However, I did find a quirk in this. While the speed is accurate, the distance on the odometers is not. The distance from my home to my workplace is 1.4 miles as per MapQuest, but the scooter trip odometer measures 1.6 miles. When P06 was set to 7.8, the odometer was accurate, but not the speedometer. Therein is the trade-off. One will be accurate, but not the other. It's weird to say the least.
@@Until_It_Is_Done Not sure why 8.4 was chosen, but they're not wrong. Comparing to my GPS, setting P06 to 10.0 makes the speedometer read about 2 MPH more than actual speed. It took a lot of trial and error, but I found 9.1 is as close to accurate as you can get.
No. On some scooters you can like Varla Eagle One (more torque) But on the M4 Pro it’s only a 500w motor and 48v battery. Scooter simply can’t do it. The controller would more than likely blow. I saw one guy modified his M4 Pro but had to put in a different controller and extra battery. In the end, if you want more torque, get a bigger scooter with 2 motors. Not worth spending the money.
@@Fiatfan incorrect. 700w peak which ain’t much. My advice, want more torque, get a dual motor scooter that has at least 1000w motors. Such as the Vlaken G3 Pro I recently reviewed.
@@Movelectrics Thanks for the reply. I was referring to the backlight on the LCD display. A customer came in today with an issue where the display had no backlight. I performed a P99 reset, and the backlight came back, but now I would like to adjust it to make it brighter.
@@Fiatfan At level 5, acceleration is still sluggish. The latest KuKirin M3 I reviewed is a much better scooter. More torque plus the build quality is the best of seen so far. It’s also cheaper and not to mention, IPx7 Full review ruclips.net/video/wEcxB5D67oI/видео.htmlsi=gL3Xa_lUlWvyO5Uz
Actually, you can do this without changing the parameters. You have 3 speeds which you modify by pressing Mode once. The 2nd speed should limit to 25 iirc
can someone help me I have a Kugoo tf-100 and I can't accelerate because my scooter thinks it's braking because the brake light comes on but it's not actually braking.
@Movelectrics ZQ-100 , 48V Battery, 1000W Mottor, Tire 10inch. Megnet 30. My weight is 70KG. Battry Fully Charge. Voltage is 55... i want to know how many K/M it should go ?
@@danishwaleed9804 not familiar with this scooter. Depends on weight, temperature, speed, hills, start/stop. Faster you go, faster battery drains of course. I always found in most cases, the max distance that’s advertised for scooters, cut that almost by 40% if you are going the higher end top speed. Everyone rides different though, so there is no definitive distance.
@@omidhassani661 it’s a 48v battery so this is the correct setting. You cannot make this scooter go any faster than 45km/h. I explain this in the video.
@@Movelectrics 😡 I wanted to buy this, but now I'm rethinking it. I want the lights set to blue and not look like a flashing circus rolling down the street at night.
@@nonenone9338 to be honest, they attract too much attention in my opinion and rather be able to turn them off. Some people actually put black tape over them. It is a decent scooter though! Check out my final review on it and I explain everything ruclips.net/video/Z05qUoh-Skc/видео.html&si=EnSIkaIECMiOmarE
I turn my scooter on with the key and the volt display comes on and i press the power button to get it going, now i turn it on volt display cones on and the meter comes on without me pressing the power button and then it goes off and i press the power button and it doesn't turn on,any suggestions would be appreciated
@@Movelectrics never,the manual ses not to, sometimes it resets itself and starts working like it suppose to,but the last few days it's not working properly,it does have 7200 miles on it
Unfortunately the only way is to disconnect from inside the deck or just put black tape over them. If you don’t feel confident enough, get a qualified person to do it.
I need help with my ix5 scooter the yellow wire has burn and now my motor will not go ,it just stutter I think it's the hall sensor or could it be the controller not sure
Do you know how to change max speed of each gear? In my country is illegal to have a scooter that can drive above 25km/h, and policeman can check it. And they know how to change modes, so I want to be smarter and lock 3rd gear at 25, but second gear I would let max speed
Just ordered the 2022 18AH version. Can't wait! Only worry is some reviews saying it can come with stem wobble out of the box. Any suggestions on how to make stem as strong and study as possible? Thanks 👍
Congrats! Stem wobble seems to be an issue in the earlier models. Mine is absolutely fine. Like any scooter, don’t pull/push like crazy on the handlebars. Double check all the screws/nuts/bolts etc. Enjoy ⚡️
@@Movelectrics So i bought a motor a controller and display but the seller said that the display is the same for the 36v and the 48v and only the 48v controller has a yellow wire bit the 36v controller does not have
Hi Do you mean decrease the top speed? You need maximum of 25km/h? If so, you have the decrease setting P15 (power output % ) until you get the desired speed. Or you could simply use gear1. But if it’s for regulations, changing the p setting is the only way.
Hello one thing I CANT for the love of my life understand. Please someone help me. If we change as you say the P setting on our own, who can assure the police for example that we won't change it again back to higher speeds,on our own again? I'm asking that because I'm Greece maximum speed can be 25kmh. And the vehicle by its built must not be able to offer higher speed. So will we be fine or not if we change its p setting, please????
@@Movelectrics yes , forgetabout greece, I'm asking if changing the p setting on our own is enough to be ok with the guidelines in general in Eu. Or is it not and needs a certificate that it is blocked by its manufacturing to this speed limit? I need a good motor for long distances , I don't mind the 25 km/h I just need a good battery and motor so i can't buy scooters of 200$ ,this is why I'm asking you
My dashboard keeps making beeping sound and shuts off. I also noticed a USB slot on the back. How do I get the display to appear again after turning it back on. The battery is fully charged. The display is off and wont start. Any thoughts?
USB slot is only for firmware on the displays (not for charging) When it beeps, is there an error code showing? Can you join my FB group and post a quick video there also? bit.ly/2NMeXIY
Hello, Thanks for the video :) does 18AH version have the same TF-100 screen please ? I am in France, is it possible to change the speeed settings for 25km/h maximum ?
Not possible as explained in the video. You are giving the incorrect information to the controller. GPS speed test the scooter and you will see the true speed is maxed out at 45km/h
Thank you for the video. You recommand to leave the wheels size setting untouched, but what if that number is set higher than the actual wheels size ? I have the Kugoo Kirin G2 pro. Wheel size is set at 9 inches, but the actual wheels size is 8.5 inches.
Like I mention in the video, there is no speed hack for this scooter. Changing magnets is giving the incorrect information so the display is not accurate. If you GPS test the scooter with an app, you will see up to a maximum of 45km/h. Ride safe 🛴
I bought one of these and it’s defective. As soon as I start moving the speedometer says 15mph when I’m actually going 2mph. It doesn’t go 27 mph. Maybe 15mph tops down hill. It’s made with cheap plastic. This thing completely sucks. Don’t waste your money.
Not possible as I explain in this video. You must have changed the p-settings from the default. Doing this will give incorrect speed readings. GPS speed test the scooter and you will see the maximum speed possible is around 40-45km/h
@bollejoker111 I don’t need proof. But it ain’t possible unless you modify the controller and have a bigger battery. Changing magnet settings is giving the incorrect information so the display is not accurate. Again when you GPS speed test the scooter with a phone app for example, you will see it ain’t possible. Best to keep everything default.
P12 is unknown. Therefore I would leave it alone. Kugoo have changed these settings numerous times since the Pro model was released. Also P16 is cruise control. I don’t suggest touching this because it’s dangerous.
@@Movelectrics Nice! mine is set to 5 by default and changed it to 1 nothing happend I guess, but in the same day when I was going up a hill I was giving it a little gass and at the end of the hill it stopped, doesn't work anymore the store that I bought it from said they will repair it (I don't think this has to do anything with the p12)
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
🚨 P16 is cruise control. I think it’s a dangerous setting to have, so leave it be.
⚡️ Must watch Kirin M4 Pro playlist ruclips.net/p/PLOIER5h7JLytR_Q-_9ZjMB9hidFy3S_qo
🛴 Official KUGOO site and latest discounts (automatically applied) bit.ly/47guuEZ
Xiaomi/Kugoo and most scooters don’t have good water resistance. But you can definitely improve it yourself for any scooter. This is the video from last week about water resistance improvement ruclips.net/video/ZSFcnzdgKp0/видео.html
It maybe dangerous for some people but if and when e scooters become legal Cruise control may come in handy
Why is cruise control dangerous?
@@MYKI33334 I prefer to have full control over the speed of the scooter. I never liked this feature.
I ordered one of these a few weeks ago it came within a couple of days but I've only just got round to unpacking and setting it up, just a quick heads up to anyone who's waiting for delivery of one of these scooters, the instructions on how to unfold it a very vague I was getting extremely pissed off with working out how to lock the stem in place(it doesn't tell you in the instructions), I had to look on RUclips for a vid, turns out you have to give the stem a Wright good shunt forward to snap it place, before I knew this I was trying to do it for ages and getting extremely annoyed, all good now.
Agree. Just need a bit of force to get it to click fully into the stem and twist the safety pin in place.
Took me a bit to figure out too. You have to give a good jerk to lock it in.
@@stupid47 😂😂😂 same
What exactly was P12 even though its not to be changed what does it do
Finally a quick, simple and well explained video on the kugoo settings! I have the ienyrid m4 pro which is basically the same scooter under a different name. Has the same controller and everything so everything in this video applies to me too. Thanks for this video buddy it’s helped me a lot and it’s easy to follow 👍🏻👍🏻
No worries Daniel, ride safe ⚡️
I'm looking at the ienyrid M4 pro myself, do you still have the scooter and would you recommend it?
I no longer have the scooter but I did a final review on it (linked below) ruclips.net/video/Z05qUoh-Skc/видео.html&si=EnSIkaIECMiOmarE
@@MovelectricsJust a question, I bought a Kugoo Kirin M4 and recently I bought a Kugoo Kirin G2 max, do the settings work the same for those 2 scooters or it is something diffrent? Thanks
Good video mate. Short and sweet and to the point.
@@Dee33321 thank you for the support
Ordered one of these last week, so excited for the next batch to ship out 😩
You will be very happy ⚡️
I've been waiting for over 11 days now for my one... They're always late to sending tracking numbers
Where you order from?
@@Movelectrics uk
Hello? Is it possible to toggle and untoggle the speed limiter faster? Rather than going into p settings and spam clicking a single button? Thank you
@@boss-lk1zz not possible on the M4 Pro
Just a heads up P16 is for the cruise control if you want it on/off
Yes I have this in the pinned comment. Thank you ⚡️
I actually modified P6 and set it to 8.4 instead of 10 so i could get a more accurate speed reading on my scooter. The only actual way of getting more speed is to get tires with a larger diameter which requires quite a few modifications to allow for those larger tires to fit.
Most scooters I’ve had never have accurate speed readings from the display. Sometimes they are off by only a few kms. I always leave it it the default p settings for wheel diameter/magnets etc.
I always test with a GPS app.
Can I ask why 8.4 is more accurate when m4 pro has 10" tires?
@@Until_It_Is_Done the meter is off accuracy by 1" on mine. It's different for everyone's scooter though. Also the original tire was slightly smaller than 10 inches, which I had replaced recently along with the motor.
After comparing to my GPS and my mountain bike speedometer, the best setting for P06 is 9.1 for the most accurate speed.
However, I did find a quirk in this. While the speed is accurate, the distance on the odometers is not. The distance from my home to my workplace is 1.4 miles as per MapQuest, but the scooter trip odometer measures 1.6 miles. When P06 was set to 7.8, the odometer was accurate, but not the speedometer.
Therein is the trade-off. One will be accurate, but not the other. It's weird to say the least.
@@Until_It_Is_Done Not sure why 8.4 was chosen, but they're not wrong. Comparing to my GPS, setting P06 to 10.0 makes the speedometer read about 2 MPH more than actual speed. It took a lot of trial and error, but I found 9.1 is as close to accurate as you can get.
Isnt P12 for acceleration changes? In kugoo kirin x1 it does change there acceleration
No. Different scooters have different settings and spec. Plus sometimes different displays.
@@Movelectrics so on M4 pro you can't change acceleration speed?
No. On some scooters you can like Varla Eagle One (more torque)
But on the M4 Pro it’s only a 500w motor and 48v battery. Scooter simply can’t do it. The controller would more than likely blow.
I saw one guy modified his M4 Pro but had to put in a different controller and extra battery. In the end, if you want more torque, get a bigger scooter with 2 motors.
Not worth spending the money.
@@Movelectrics there are m4s with 700w tho
@@Fiatfan incorrect. 700w peak which ain’t much. My advice, want more torque, get a dual motor scooter that has at least 1000w motors. Such as the Vlaken G3 Pro I recently reviewed.
Hi. How can you change from ODO to Trip?
Press mode until you see current trip from what I remember
which wire do i need to cut off to make it unrestricted?
or is there any way to make it go past that 45 km/h mark?
No wires to cut. Follow the instructions in the video. Not possible as explained to ‘speed hack’ this model
@@VM61131 cut the big wire coming from the battery
@@miketrav if i’m cutting that xt60 cable, the thing isn’t going to work.
Never cut wires from there
P-settings is how you unlock the speed as I show in the video
Can I change the electric motor regenerative braking? M4 Pro 18aH
There is no regen braking on the M4 Pro.
Is there any setting for backlight?
@@madrian_hello no. Steady red and flashes when you brake
@@Movelectrics Thanks for the reply. I was referring to the backlight on the LCD display. A customer came in today with an issue where the display had no backlight. I performed a P99 reset, and the backlight came back, but now I would like to adjust it to make it brighter.
@@madrian_hello there is not setting for this on the M4 Pro
@@Movelectrics thanks bro 👍
Hi boss how do I change the rbg to green?
Not possible unfortunately
Teren îs a led controler inside the scooter, next tonthe battery.
Mine got two buttons who control the led collors, and the pattern
Dobry den prosim Mam novy Kukirin M4 najdu v nabidce Kolik km Mam ještě k dispozici na dojetí?
I don’t understand what you are asking. Do you already have the M4?
Is this the same for ienyrid M4 pro ?
As far as I’m aware ⚡️
Hello, is there a way to limit the scooter so that it goes max 25km/h
Yes
Follow this video and you can adjust the p-setting
Isn't P12 for acceleration intensity?
I did not find a purpose of this p-setting
@@Movelectrics try using p12 on 5 and compare to on 1
@@Fiatfan At level 5, acceleration is still sluggish. The latest KuKirin M3 I reviewed is a much better scooter. More torque plus the build quality is the best of seen so far. It’s also cheaper and not to mention, IPx7
Full review ruclips.net/video/wEcxB5D67oI/видео.htmlsi=gL3Xa_lUlWvyO5Uz
@@Movelectrics so m3 has faster acceleration?
@@Fiatfan definitely. Motor is much better.
Hey! Quick question! Is it possible to make it go the legal limit? 25kmh?
Yes just follow the power p-setting as I explain in this video and lower the value until you are happy
Actually, you can do this without changing the parameters. You have 3 speeds which you modify by pressing Mode once. The 2nd speed should limit to 25 iirc
my friend tell me what about those LCD TFs that have nfc, like for example the sealup tf-191? How do I enter configuration mode?
Not possible. TF 100s are older type displays.
can someone help me I have a Kugoo tf-100 and I can't accelerate because my scooter thinks it's braking because the brake light comes on but it's not actually braking.
Did you change any p-settings?
@@Movelectrics no I was driving it normally and suddenly it happened
@@Klaussyx sound like your brake leaver is faulty. Sensor good be causing this. Best to get it checked out.
@@Movelectrics thanks i looked and I move something and it worked
My Scooter is 48v / 1000W motor... i want to know how many KM it should go in full charge ? mine is going just 18KM ... is it ok ?
@@danishwaleed9804 what scooter you have?
@Movelectrics ZQ-100 , 48V Battery, 1000W Mottor, Tire 10inch. Megnet 30. My weight is 70KG. Battry Fully Charge. Voltage is 55... i want to know how many K/M it should go ?
@@danishwaleed9804 not familiar with this scooter.
Depends on weight, temperature, speed, hills, start/stop. Faster you go, faster battery drains of course.
I always found in most cases, the max distance that’s advertised for scooters, cut that almost by 40% if you are going the higher end top speed.
Everyone rides different though, so there is no definitive distance.
Hi what happens if i change P 03 48. Voltage to 52 will it increase the speed?
48v is stock. Don’t change anything. It aint a 52v scooter.
@@Movelectrics oh yeah but I'm wondering it's like can 48v stock be overvvoltaging?
@@omidhassani661 it’s a 48v battery so this is the correct setting. You cannot make this scooter go any faster than 45km/h. I explain this in the video.
@@Movelectrics ok thanx for the information man
Do you have a video that explains how to change the different speed setting? I think they call then gear settings?
Just press mode button and choose gear 1, 2 or 3
How do you set led lights to one color?
Not possible unfortunately.
@@Movelectrics 😡 I wanted to buy this, but now I'm rethinking it. I want the lights set to blue and not look like a flashing circus rolling down the street at night.
@@nonenone9338 to be honest, they attract too much attention in my opinion and rather be able to turn them off.
Some people actually put black tape over them.
It is a decent scooter though! Check out my final review on it and I explain everything ruclips.net/video/Z05qUoh-Skc/видео.html&si=EnSIkaIECMiOmarE
My scooter pop-up error code e6,do you know why?
Here is the list escootermod.com/kugoo-m4-pro-error-code-fixes-repair/
Can you turn the led lights off on the scooter as I don't want them on
You can disconnect from the controller but I heard people just put black tape over them.
I have the m4 PRO 18ah i checked the magnets thing and it says 35. I haven’t touched it before so I wonder if it’s supposed to be 35
Same motor. What did your display saying when going too speed?
@@Movelectrics sorry mate I take that back. I might’ve accidentally messed with it before! Cheers.
I turn my scooter on with the key and the volt display comes on and i press the power button to get it going, now i turn it on volt display cones on and the meter comes on without me pressing the power button and then it goes off and i press the power button and it doesn't turn on,any suggestions would be appreciated
Sounds like a battery issue. Did you turn on the scooter ever while charging?
@@Movelectrics never,the manual ses not to, sometimes it resets itself and starts working like it suppose to,but the last few days it's not working properly,it does have 7200 miles on it
I'm thinking about buying a new meter
Do You know if it’s possible to disable the damn disco lights?
Unfortunately the only way is to disconnect from inside the deck or just put black tape over them.
If you don’t feel confident enough, get a qualified person to do it.
I just put black electrical tape on mine
I need help with my ix5 scooter the yellow wire has burn and now my motor will not go ,it just stutter I think it's the hall sensor or could it be the controller not sure
And also I have a kugoo m4 and the fork is loose everything I touch the brakes there is to much play
@@colinjeremiah7815 100% stop riding and tighten everything on the M4. Regards to the ix5, I never had this scooter unfortunately so cannot help.
Do you know how to change max speed of each gear? In my country is illegal to have a scooter that can drive above 25km/h, and policeman can check it. And they know how to change modes, so I want to be smarter and lock 3rd gear at 25, but second gear I would let max speed
Good question but not possible. You cannot customise individual gear speeds.
Hello. Is it worth it to put the power thing to 100. I have it 80 i got a brand new battery
100 will get you the max speed. Or you can tailor it by lowering it. Whatever suits you best and you are most comfortable with.
@@Movelectrics Thank you
Just ordered the 2022 18AH version. Can't wait! Only worry is some reviews saying it can come with stem wobble out of the box. Any suggestions on how to make stem as strong and study as possible? Thanks 👍
Congrats! Stem wobble seems to be an issue in the earlier models. Mine is absolutely fine. Like any scooter, don’t pull/push like crazy on the handlebars. Double check all the screws/nuts/bolts etc.
Enjoy ⚡️
@@Movelectrics ah good to hear! Thanks for swift reply. Really like the vids. Best on RUclips for e-scooters. Appreciated and Subscribed 🤝
@@Until_It_Is_Done honestly thank you for the support 👊🏼
Hello,
I hope you're doing well with your 2022 18AH :)
does 18AH version have the same TF-100 screen please ?
thanks!
@@ahmedhentati598 yes they still use tf-100 display/throttle 👍
Does it work on normal m4 ?
There is no speed hack like I explain. Not possible.
Mine won't even allow me to access p 1,3,5,6,7,8,10,11,12,13,14,15,. Then goes straight to 99🤷♂️?
@@jbwether what model scooter you have? What display you have (number?) is it TF 100? What country you live in?
@@Movelectrics U.S.A... It's an ienyrid m4 pro s+ older version. So practically the same scooter, and the exact same display
@@jbwether what speed you getting? Max speed?
@@jbwether oh i have the Same it dosent work
I put my wheel diameter from 8.0 to 10 and got 5mph extra out of it. What’s that all about. It’s a G3 36v scooter. M4 style
You don’t get extra ‘speed’ due to changing settings like wheel diameter. Test the scooter with a GPS and you will see.
Its the 700w offroad version?
Off-road version? Not on the M4 Pro. KUGOO G3 Pro is built for that.
How do you turn on and off gest mode
Gest mode?
A yellow wire is missing from my controller it should go to the display but it is not there HELP MEEEEEE
@@Milán-j6i ? Scooter new? Display working?
@@Movelectrics yes
@@Movelectricsonly the motor is changed but it has all the wires
@@Milán-j6i I’m not understanding. Scooter is new and you changed the motor?? Can you explain more please
@@Movelectrics So i bought a motor a controller and display but the seller said that the display is the same for the 36v and the 48v and only the 48v controller has a yellow wire bit the 36v controller does not have
Sorry the setting P12 what is?
P12 doesn’t have a purpose. Cannot find anything on this setting.
how to limite the top to 25km/h ?
Hi
Do you mean decrease the top speed? You need maximum of 25km/h?
If so, you have the decrease setting P15 (power output % ) until you get the desired speed.
Or you could simply use gear1. But if it’s for regulations, changing the p setting is the only way.
Hi thanks for the answer
Yes i meant the maximum speed
Hello one thing I CANT for the love of my life understand. Please someone help me. If we change as you say the P setting on our own, who can assure the police for example that we won't change it again back to higher speeds,on our own again? I'm asking that because I'm Greece maximum speed can be 25kmh. And the vehicle by its built must not be able to offer higher speed. So will we be fine or not if we change its p setting, please????
Can’t answer this question as I don’t live in Greece.
@@Movelectrics yes , forgetabout greece, I'm asking if changing the p setting on our own is enough to be ok with the guidelines in general in Eu. Or is it not and needs a certificate that it is blocked by its manufacturing to this speed limit? I need a good motor for long distances , I don't mind the 25 km/h I just need a good battery and motor so i can't buy scooters of 200$ ,this is why I'm asking you
Mine only does about 21mph on speed 3 setting, wonder if I’ve missed something on the settings. I’m about 12stone
What’s your tyre pressure? If it’s low, the speed will be reduced.
I have mine at 45psi
@@Movelectrics it’s solid tyres. I have a hitway H5 same as the kugoo M4 pro
@@kizlo14 the scooter came with solids? Strange!
@@Movelectrics I may be mistaken. Is it a solid front and pumped up rear normally? Thanks for the help
@@kizlo14 both are air filled on the KUGOO scooters
Hey, mine is going 45km/h is there anh chance to get 70km/h ?
No possible as explained in this video. If you want faster speeds, you will have to buy another scooter.
My dashboard keeps making beeping sound and shuts off. I also noticed a USB slot on the back. How do I get the display to appear again after turning it back on. The battery is fully charged. The display is off and wont start. Any thoughts?
USB slot is only for firmware on the displays (not for charging)
When it beeps, is there an error code showing? Can you join my FB group and post a quick video there also?
bit.ly/2NMeXIY
i got a similar scooter and the same problem but doesn’t beep. got no power to the display any ideas?
Check all connections?
Hello,
Thanks for the video :)
does 18AH version have the same TF-100 screen please ?
I am in France, is it possible to change the speeed settings for 25km/h maximum ?
Yes. You can change the power p setting as explained in the video to tailor maximum speed. Or just use a lower gear.
My scooter dosnt go 40 always stays at 30 or 25
P settings same as mine?
What’s your tyre pressure?
What weight are you?
What’s the speed with no weight?
@@Movelectrics I weight like 85 but I have the setting on default gonna change them later
@@marksullivan4673 make sure your tyre pressure is around 45psi. If it’s low, the speed will decrease.
P7 does make it faster I set it to 2 I'm flying lol only thing is the speedometer won't read but if I'm on normal settings the speedometer works fine
Not possible as explained in the video. You are giving the incorrect information to the controller. GPS speed test the scooter and you will see the true speed is maxed out at 45km/h
I did GPS test it I'm getting 50kmph but I have a different model scooter
@@marcus5556 this video is about the M4 Pro. What model you have? P-settings can vary greatly from different models.
😂a different model scooter ya say after the fella put ya are in your place. Ya clearly have no clue what you are shiting on about.@@marcus5556
👍thanks👍
Thank you too
Thank you for the video. You recommand to leave the wheels size setting untouched, but what if that number is set higher than the actual wheels size ? I have the Kugoo Kirin G2 pro. Wheel size is set at 9 inches, but the actual wheels size is 8.5 inches.
I can’t speak for the G2 but maybe the settings don’t have the option of 8.5?
It actually does have the 8.5 inch parameter which is causing my confusion. Anyway, thank you for the time and answer. Good luck with your channel !
@@LEFF90 check other videos to see what the default setting is. I wouldn’t be worried to be honest.
Set it to 9.1. A lot of trial and error with my GPS determined that this setting is the most accurate you can get.
I have to slow down my speeds just incase because if i get this it will be my first e scooter so ill just slow it down
Just use gear 1
I put the number of the magnets 25 and now the speed it's 70 km an hour.
Like I mention in the video, there is no speed hack for this scooter. Changing magnets is giving the incorrect information so the display is not accurate.
If you GPS test the scooter with an app, you will see up to a maximum of 45km/h.
Ride safe 🛴
Lol
I measured with the app komoot on my phone and the real speed is 51 km an hour and I weight 99 kg .
Not possible unless the scooter is off the ground or you changed the p settings and gave the scooter incorrect information.
When i try to enter settings there is a code. When can I find what is it?
@@ItayShoshani-n2f a code? What scooter you have?
I have a Gowheels m4 pro, it looks like a sticker brand because the specs are exactly the same as kugoo/kukirin
I bought one of these and it’s defective. As soon as I start moving the speedometer says 15mph when I’m actually going 2mph. It doesn’t go 27 mph. Maybe 15mph tops down hill. It’s made with cheap plastic. This thing completely sucks. Don’t waste your money.
Dis you check all P-settings? Compare them to this video ⚡️
I got mines to 53km an hour and I didn't change anything!!! I'm only 120pounds.
Double check your p settings are all default. Sometimes they can be incorrect from factory. Also a way to verify speed is GPS testing it.
Nope I had a speedometer app plus the car next to me and I hit the same speed
@@rosamerlujan5510 definitely must be special edition
@@Movelectrics is not I'm not lying
Only joking
i go 56 on a less then full battery
Not possible as I explain in this video.
You must have changed the p-settings from the default. Doing this will give incorrect speed readings.
GPS speed test the scooter and you will see the maximum speed possible is around 40-45km/h
@@Movelectrics ok need proof ? i make a video
@bollejoker111 I don’t need proof. But it ain’t possible unless you modify the controller and have a bigger battery.
Changing magnet settings is giving the incorrect information so the display is not accurate.
Again when you GPS speed test the scooter with a phone app for example, you will see it ain’t possible. Best to keep everything default.
@@Movelectrics oh sorry i was wrong full battery 68
and i changed nothing i only modify ninebots
what is p12v
P12 is unknown. Therefore I would leave it alone. Kugoo have changed these settings numerous times since the Pro model was released.
Also P16 is cruise control. I don’t suggest touching this because it’s dangerous.
Someone told me that p12 is the acceleration
As far as I know, the TF 100 display doesn’t have this function. I have mine on zero start and quite happy.
@@Movelectrics Nice! mine is set to 5 by default and changed it to 1 nothing happend I guess, but in the same day when I was going up a hill I was giving it a little gass and at the end of the hill it stopped, doesn't work anymore the store that I bought it from said they will repair it (I don't think this has to do anything with the p12)
If you were pushing it hard up a hill, could have blown the controller possibly.
I'm 135lb and get 42mph
Great! Ride safe ⚡️
Lovely accent.))
Thank you! Glad you understood me haha
that's not a hack
@@vegePOG exactly. That’s why I explain each setting and why some people input wrong information on the p-settings giving inaccurate speed readings.
@@Movelectrics you're amazing brother. Keep up the good work!
@@vegePOG thank you the support ⚡️
My scooter is a simple 2400w motor and it goes 75klm without any hacks
What scooter do you have? I had once a scooter that went 73km/h but definitely them speeds ain’t safe.