How to acrylic / silicone render how to render wall old wall silicone render thin coat rendering

How to acrylic / silicone render how to render wall old wall silicone render thin coat rendering on an old wall
videos before that led to this moment
removing render • how i remove render an...
Scud coat • how to slurry scud coa...
Scratch coat • How To Apply Scratch C...
float coat and finishing render • How I Finish Render a...
tools used for this whole job from start to finish
refina trowel 14" amzn.to/3r8EBvj
16" amzn.to/45TW2yM
Tysack trowel 13" amzn.to/46hsGu3
float amzn.to/3Lvk4YD
A float u want to try out = amzn.to/3Pkucom
water brush refina amzn.to/3Riun6a
water buckets amzn.to/3t3KCtx
more buckets x10 = amzn.to/46ckmM6
float amzn.to/45RFfvD
gloves amzn.to/3P3rvXW
Hammer i am using amzn.to/47co0qG
bolster / chisel = amzn.to/43NhkfF
googles = amzn.to/3ObKMGq
gloves amzn.to/45402vF
similar grinder amzn.to/3Qi8FyC
blades for stone ect amzn.to/3DwXGJV
blades for metal amzn.to/3q7UMII
feather edge amzn.to/3EKoF5z
serrated edge amzn.to/3t23xF4
chipping drill similar amzn.to/3Lq3qcS
spoke scratcher = amzn.to/3sUNg55
comb scratcher amzn.to/46ckv1P
dasher amzn.to/3rgSIP7
Spear and Jackson bucket trowel that is still going strong for me after many years = amzn.to/2pcpReS
Refina trowel pack and holder = amzn.to/33PbCvi
All amazon links are affiliated links will cost no extra to buy from but we might get a %
tools links direct
www.refina.co.uk/
Find us and like us here
/ macplasterin. .
Tweet us here
/ macplastering
/ macplasteringservices
our amazon store affiliate www.amazon.co.uk/shop/macplas...

[@markneeson7162]

Great job Joe. Keep er lit.🔥👊

[@macplastering]

Thanks mate 👍

[@patricklynch236]

Looks beautiful 👍🏻

[@macplastering]

I do love this finish myself

[@markhep]

Good job mate 👍👍

[@macplastering]

Cheers man love this finish hard old work but worth it

[@markhep]

@@macplastering yere it look quite good like it 👍👍

[@charleslassiter6082]

thanks bro really kind you sharing your knowledge with us, cheers mate. Charles (NZ)

[@macplastering]

Any time buddy hope to have more of these uploaded in future

[@markneeson7162]

Fassa is a really slow drier, whether it’s acrylic or mono. Water can damage it up to 2 or 3 days after application.👍

[@macplastering]

Never used it as a mono myself but have been told its very nicevto work with

[@ernestogonzalez17]

You did a great job on this house brother , I watched the 4 videos on this project and damn there was a lot of work . But the finish looks amazing 👌🏽 keep up the good work mate

[@macplastering]

Thanks man currently down and out with a bad flu 🤧

[@ernestogonzalez17]

@@macplastering that’s no bueno my friend I hope you get well soon 🙏

[@macplastering]

back at it now lol

[@ernestogonzalez17]

@@macplastering I’m glad to hear that brother

[@macplastering]

the test video just went live mate

[@lmilne4859]

Top video buddy good lad work out on the arms. Haven’t used it but does seem to easier than scrapped back render ?

[@macplastering]

not sure if it is easier as you have all the rendering to do before hand where as the scrapped gear is a one coat or like i like ti double coat booth hard work LOL

[@lmilne4859]

@@macplastering
True. Buddy.

[@c2k911]

To paint acrylic render can you use exterior self primed paint 2 coats ?
Or do you have to use a special sealer for 2 week old acrylic render?

[@macplastering]

@c2k911 if its self priming should be OK but you could do a small test 1st? Agin the acrylic will be set and dry and as its not old it will be clean

[@joesheehy5304]

Hi mate. Just wondering when you are doing a job that you are coating over sand and cement would you float and sponge the sand cement coat or just smooth rub finish then prime? Thanks

[@macplastering]

Would still sponge mate have the other stages of this job on channel and a few others on this type of acrylic render

[@patricklynch236]

Should have used the mesh roll to prevent cracks and add durability other than that good video bro👍🏻

[@Drunk3nMonk3y72]

That would be in the base coat

[@macplastering]

Put mesh in all cracks areas or joints in that block to brick but didn't wrap the whole job

[@macplastering]

@@Drunk3nMonk3y72 yea did the areas tgat needed it but not the whole job just windows and joints ect thing is it should help but still isn't a 100%

[@patricklynch236]

@@macplastering top stuff pal good video you're good at you're work and it shows👍🏻

[@macplastering]

@@patricklynch236 thanks again mate appreciate the support 👍

[@noodles8203]

Would this work over painted render?

[@katsucurry9420]

Depends what condition the painted render is in.. If the paint on the render is solid and not flaking it should be fine.. I would personally give it a coat of primer and wait a few days for it to completely dry then go over top with thin coat silicone

[@macplastering]

Will have avideo on that subject in coming weeks mate

[@markneeson7162]

Acrylic will work fine over existing s/c, another option is to spray Corksol on. It’s a great product too.👍

[@macplastering]

@@markneeson7162 have not used that gear has it got Cork in it?

[@markneeson7162]

@@macplastering yeah look it up Joe. You can use it as a finish externally or spray it on internally and skim over it, improves thermal efficiency about 30%. Stuart Roberts did an interview recently with Jamie Orr from Corksol on Trowel talk.👍

[@Ireland-bc2gx]

Tidy work lads the finish is determined by the size of the aggregate,and u can add small amount of water too the finish ask the
Rep for the manufacturer

[@macplastering]

Yea I think they said one time a cup or 2 but I tend to just go as it is just give it a real good mix 😆