Great video a good video nobody has at least at the rate is making or altering a server smps for constant current and voltage both adjustable. Also include what would change when connecting to supplies in series. I not only can use all the smaller voltages 5v etc. But also have needs for low voltage and higher amps and opposite You are defiantly the person to do the video your very clear and give links so a person could have boards made thanks for all you share
Nice. I like that current limiter circuit with the current transformer. I need to try that one myself. I would like to see you use this devices in practice with your oscilloscope. I'm not quite sure how you are determining core saturation and optimal turns ratios. I also have a couple of mains current limiters that use a lightbulb or PTC thermistor. I find it helpful to add two of the cheap mains voltmeters from AliExpress to both sides of the mains current limiter. This lets me know the voltage drop across the bulb/ptc at a glance :-) -Jake
Maybe you can make some tester for core saturation? When using used cores it's hard to make calculations without it. The saturation can be meansured using high power, varible frequency sinusoidal power supply, and an osciloscope, when the saturation accures, the sinewave gets clipped.
Very interesting device! One possible improvement I could think of since this is a testing device: Across the main filter capacitors, add reverse polarity diodes, and maybe even replace the 200V capacitors with 400V ones. That way, in case the transistors do not switch correctly, or a connection on the transformer is faulty, the filter capacitors will not be damaged.
Those 200V capacitors aren't at risk from the output side of the converter. If there is a short somewhere, be it from transistors failing, or being turned on simultaneously, or from a shorted transformer, the worst that will happen is the capacitors empty themselves into the short. The inductor will saturate and the FWB rectifier will protect the capacitors from negative voltages.
Search the internet for "MC34063 Calculator." That is the easiest DC/DC converter to get started with. It's also just a low voltage device used to step up or step down around 1.25 to 30 volts. You really should figure those out before playing with a mains type topology. You will also find MC34063's in around 60-70% of all phone type car chargers. You can usually take one of those apart, change a couple of components, and make any voltage you want (between 1.25 and 30 volts). -Jake
@@raer7844 I know his main Russian channel has a lot more stuff on it. That won't help you a whole lot if you don't understand Russian and need an explanation. However, if you're looking for some circuits to build and are an intuitively focused type of person you can learn a lot from the Kasyan main channel. I don't understand Russian at all, but I have built a few of the circuits from the Russian channel. He has several switch mode designs on there. ....but I'm curious about his techniques too :-) -Jake
I really appreciate your good work please will the power supply to the sg3525 be connected with the ground of were the mosfet as shown in the circuit or is it separately connected
Hi, Regards from India, nice video and I learn differently from your video. Please make video on inverter using ferrite core transformer to run all types of load in domestic like fan, refreregetor
I am very happy for found your canal and you teach very gooood if you can make a high curent 14 or 15 volts battry charger and calculation transformer, l very tank you.
There is a few things I want to know here : How stable is the voltage regulation with different loads, what is the min and max output voltage, and current.?
hello Kasyan TV do you have schematic diagram or can you make a LED TV backlight tester circuit diagram 0-300v that you cant electricuted in a output voltage even 300v DC..please...thanks in advance
please can you explain me about the working of TR1 and what if I omit TR1 can this circuit be made without TR1 I m a beginner so it is not clear to me how TR1 works can u explain that
I like this power supply design and I had downloaded the file from the archive but please I want to know what is the software that can open (HV PCB) and the file (SG3524 PCB) thank you for the help
你好，我需要设计一个DC-DC降压转换器，将250V至600V的直流电压降至90V以下，同时增加电流。我了解涉及的风险。 Hello, I need to design a DC-DC buck converter that can step down an input of 250V to 600V DC to a voltage below 90V, while increasing the current. I understand the risks involved.
I notice he don't use pull down resistor in any of is igbt or mosfet in all video and i try this method and igbt blow like a fire cracked 🔥 because without a pulldown resistor the gate can get discharge at all so please don't follow his method you will blow igbt and mosfet
You sound exactly like my college physics professor! Greatful for your videos. Thank you!
Great video a good video nobody has at least at the rate is making or altering a server smps for constant current and voltage both adjustable. Also include what would change when connecting to supplies in series. I not only can use all the smaller voltages 5v etc. But also have needs for low voltage and higher amps and opposite
You are defiantly the person to do the video your very clear and give links so a person could have boards made thanks for all you share
Nice. I like that current limiter circuit with the current transformer. I need to try that one myself.
I would like to see you use this devices in practice with your oscilloscope. I'm not quite sure how you are determining core saturation and optimal turns ratios.
I also have a couple of mains current limiters that use a lightbulb or PTC thermistor. I find it helpful to add two of the cheap mains voltmeters from AliExpress to both sides of the mains current limiter. This lets me know the voltage drop across the bulb/ptc at a glance :-)
-Jake
I love ur work very nice explanation I said thank you ur wonderful
Pretty interesting, man! Beautiful work! 😃
This switch mode high power supply very nice!
please keep it up....
Maybe you can make some tester for core saturation? When using used cores it's hard to make calculations without it. The saturation can be meansured using high power, varible frequency sinusoidal power supply, and an osciloscope, when the saturation accures, the sinewave gets clipped.
Can you design a converter that you can control the output current with a op amp automatic by sensing the load current
Very interesting device!
One possible improvement I could think of since this is a testing device:
Across the main filter capacitors, add reverse polarity diodes, and maybe even replace the 200V capacitors with 400V ones. That way, in case the transistors do not switch correctly, or a connection on the transformer is faulty, the filter capacitors will not be damaged.
But aren't diodes there?! For what?! I really did not get you.
Those 200V capacitors aren't at risk from the output side of the converter. If there is a short somewhere, be it from transistors failing, or being turned on simultaneously, or from a shorted transformer, the worst that will happen is the capacitors empty themselves into the short. The inductor will saturate and the FWB rectifier will protect the capacitors from negative voltages.
thanks a lot i learnt a lot from you
Dear kasyan . İ love your videos. Please can you share with me transformer calculate and some pwm ic calculate . Thank you
Search the internet for "MC34063 Calculator." That is the easiest DC/DC converter to get started with. It's also just a low voltage device used to step up or step down around 1.25 to 30 volts. You really should figure those out before playing with a mains type topology. You will also find MC34063's in around 60-70% of all phone type car chargers. You can usually take one of those apart, change a couple of components, and make any voltage you want (between 1.25 and 30 volts).
-Jake
@@UpcycleElectronics thank you . İ know this way and i wonder kasyan way . May he use some tricks ... İ was worked 3-5 ic and ferrite material .
@@raer7844
I know his main Russian channel has a lot more stuff on it. That won't help you a whole lot if you don't understand Russian and need an explanation. However, if you're looking for some circuits to build and are an intuitively focused type of person you can learn a lot from the Kasyan main channel.
I don't understand Russian at all, but I have built a few of the circuits from the Russian channel. He has several switch mode designs on there.
....but I'm curious about his techniques too :-)
-Jake
Really great.
I would like to ask
If I can use IR2110 instead of pulse transformer or not
Thanks to you All
I really appreciate your good work please will the power supply to the sg3525 be connected with the ground of were the mosfet as shown in the circuit or is it separately connected
Supper
Is the duty cycle limited to a certain value?
Hi, Regards from India, nice video and I learn differently from your video. Please make video on inverter using ferrite core transformer to run all types of load in domestic like fan, refreregetor
WHERE IS THE CIRCUIT FILES FOR PCB ?
Please how do I calculate the current transformer
There is no link for daigram can u plz help???
I am very happy for found your canal and you teach very gooood if you can make a high curent 14 or 15 volts battry charger and calculation transformer, l very tank you.
There is a few things I want to know here : How stable is the voltage regulation with different loads, what is the min and max output voltage, and current.?
hello Kasyan TV do you have schematic diagram or can you make a LED TV backlight tester circuit diagram 0-300v that you cant electricuted in a output voltage even 300v DC..please...thanks in advance
please can you explain me about the working of TR1
and what if I omit TR1
can this circuit be made without TR1
I m a beginner so it is not clear to me how TR1 works
can u explain that
I like this power supply design and I had downloaded the file from the archive but please I want to know what is the software that can open (HV PCB) and the file (SG3524 PCB) thank you for the help
SprintLayout 6
你好，我需要设计一个DC-DC降压转换器，将250V至600V的直流电压降至90V以下，同时增加电流。我了解涉及的风险。
Hello, I need to design a DC-DC buck converter that can step down an input of 250V to 600V DC to a voltage below 90V, while increasing the current. I understand the risks involved.
PLEASE BUILD A TRANSFORMER CIRCUIT OF 220V VAC MONOPHASIC TO 3 PHASE 220V .GREETINGS
Skema?
I notice he don't use pull down resistor in any of is igbt or mosfet in all video and i try this method and igbt blow like a fire cracked 🔥 because without a pulldown resistor the gate can get discharge at all so please don't follow his method you will blow igbt and mosfet
ขอบคุณ ฉันติดตามช่องของคุณ ที่ต้องการของฉัน
Can you please do a DIY power supply on Amplifier power supply which consists of Dual rail power ex : +/- 50v with Feedback for less voltage drop!?
I am need arabic