Another question our power is a bit wonky here in the Philippines. If AC isn’t properly grounded and I use the solar array to power up do I need to ground the inverter someway?
I've just bought one to be installed in Zimbabwe my question is will l be able to pair it with my mobile device since the professionals there don't have a number/reference from you? Thank you.
Hello sir..i am so glad i saw your video on this offgrid system..you mentioned that if it is first time to powerup a brand new inverter, battery shld not be used as power to wake up and setup the inverter. It shld be open thru ac supply..in my case the area has no grid present.what is the optiion if i may know..thank you
Hello, I hope you can clarify something for me. At the 5:10 part of the video you say you have a 50AH battery connected. Isn't the battery a 100AH battery? The reason I am asking is that I have Dyness B3 batteries rated at 75AH each. However my lux power SNA5000 says its a 50AH (just like yours) When I add more B3 batteries it goes up at 50AH per battery as opposed to 75AH per battery. I believe the SNA5000 has a 200AH battery limit. I have 4 x B3 batteries and 2 x SNA5000 inverters. I was told to parallel the batteries (300AH) and connect them to both the inverters at the same time. I also want to parallel the inverters to a single phase . The webpage does not give me the option for paralleling that is shown in the manuals? Is there a forum out there where I can get some assistance?
Hi Andy, I am struggling a bit with my dongle, the lights not going solid, the new app also doesn't allow me to find my WiFi connect...Can you pls assist
Thank for this. I did the unthinkable and reset the wifi thing to factory default. Could you perhaps share the UART settings? I am sure it defaulted the baud settings, so now it does not connect to the inverter
Hi. I see there is a connection facility for a generator. Is there a place where one can set the charge rate for that port as to prevent charger overloading the generator?
So glad someone made this video. Just got the same setup. Exited to get it up and running. Can you maybe tell me how many 330w panels I can put on it. I see the voltage is 385
It has a dual mppt. 3200w /tracker. I suggest you keep your solar to 2900w or less (per tracker) which allows for power spikes during bright cold days.
@@johnyjansenvanvuuren1980 Luxpower will upload a single phase parallel tutorial tomorrow. Soon to be followed by the 3-phase parallel tutorial this week.
Please, explain how to use a generator for charging battery? I connected wires from generator to L and N to invertor. It doesn't work. Just trying to charge (i see on display) and disconnected. It is going again and again everytime. What is the problem? I have the same invertor and battery
Good day, installed a Lux power inverter for one of my customers. We used a Elithium Battery. I do not know the brand value to use in order for the system to see my battery in setting 3. What should I do to determine the brand setting?
can you explain pls how to enable the dongle again so i can connect to dongle hotspot. the problem is i set the dongle to station mode.i dont know how to access again to change to AP and Station
Hi, if the Dyness 48100 is a 100ah battery, why is the inverter displaying the capacity as 50ah? I have the same setup and its also displaying 50ah instead of 100ah.
Hi. Did you manage to figure this out? I also have two 100ah batteries (Greenrich) connected, but each it shows 50ah, and both in paralle it shows 100ah, and not 200ah
@@riaankoekemoer9035 Brett Franklin 2 months ago do a firmware upgrade it will read 100ah. makes no difference though it will still operate the same. Reply tomsalmonandroid2 tomsalmonandroid2 1 second ago I have same issue. Greenwich U-5000 100Ah (Well, 96Ah I think) And the LUX Inverter shows 50Ah. I guess Firmware update time
Не можу розібратись з налаштуваннями інвертора, спочатку поставив кислотні акб. Інвертор їх не заряджав по вольтажу, довелось ставити зарядку по часу, і виставляти щоб заряджав з 00:00 до 23:59 тоді запрацювало. Зараз купив літієву батарею asterion. В меню 20 брендів але не можу знайти рсошифровку чи ж мій у списку. І зараз при виборі на інверторі літжвої батареї він її взагалі не бачить
There is a program/parameter fault with these inverters when it comes to battery setup/selection. Set to lead acid battery even if you are using a lithium battery otherwise you will not get comms.
@@antonvandenberg1461 ek het 'n 200Ah Osaka op ge sit en so proebeer. Maar my inverter charge nie die battery nie. Heeltemal te complicated vir my. Kan jy dalk help.
@@abrieolwage733 Hallo, ek neem aan jy het 4 Osaka battery in serie gekoppel. Maak net seker of jy die Gel of AGM batterye van hul het en stel jou inverter op met wat jou batterye match. Dan in die menu by charge times moet jy die waardes(tye) van 00:00-00:00 verander na 00:00-23:59
Hi Andy, my inverter trips quite often at my holiday house. Is it possible to reset it remotely through the app as we are 2 hours away . It has the dongle and i have the app on my phone. Can you possibly connect to my inverter to troubleshoot. Im prepared to pay for your time. Not sure if the battery has had its day. Its shoto lithium type.Thank you
Hello Andy Have a lux power 5000 hybrid inverter with two elfbulb 100amp batteries and cannot get inverter to communicate and charge batteries Have set 03 lithium with setting 6 and other numbers but nothing maybe wire color coding on pin plugs into 485's ports.Please can you advise Many Thanks Regards .Love Your clips . Simple clear well done
Hello. A friend purchased LXP-5K Hybrid Inverters with Meritsun batteries. im trying to connect it to internet for remote monituring using application. but it requires a customer code, can you aid with that?
Hello, apologize for the late reply, do you know this battery has been compatiable with our inverter? if you have more questions, kindly send email to info@luxpowertek.com, we will help you to solve your problem, thanks
Hi Andy hope you are well I am struggling to register my Dogle USB it can not pick up my wifi even if I am close to my Router I have try everything I would like to deregister and start the hole proses from start plz help
Hi there, can someone answer my question please, if there is a video will be appreciated 🙏🏼Questions: If you turn off the power at main breaker and then back on does the inverter connect to the grid immediately?
Hi Sir, sorry for the late reply, if the SNA inverter is under on-grid mode when you turn off the main breaker, the inverter will be restarted to connect the grid in 30s. But if it is in other modes, prior to the grid connection being restarted, it's essential to fulfill the need for using AC in other modes; otherwise, the inverter will remain in off-grid mode. Hope this answer can help you.
There is a program/parameter error with these inverters. Set battery selection on inverter to lead acid, even if you are using a lithium battery otherwise there will be no comms
Приветствую Ошибка внутренней связи 2 Не принимает с сети и не отдаёт в бекапе Батарею показывает Сеть показывает Без сети пишет статус Нормал Как появилась сеть сразу в ошибку падает в статусе! Кто подскажет?
Hello sir, is your supplier an installer or a distributor? If they are an installer, they can request their distributor to generate the code and provide it to you. If they are a distributor, they have the ability to create the code themselves.
Hi, I am struggling to set solar charging batteries bcz batteries are only charging on Ac, when I connect solar panels only doesn't show charging, I am using luxpower inverter, 5 x545w panels, lithium battery,
Hi Sir, Apologize for the delay reply, I wonder that you wanna to set for PV charge priority, right? Please share us with your inverter SN, we will check your settings. Thanks
@@TitusMogane Hi Sir, For our SNA series, you can set the AC first working mode to achieve this function. In this mode, the AC will power the load first, and any excess power will be used to charge the battery. Hope this reply can solve your question.
"Show you how to paralelle not one, but two machines. "- What am I watching ? , put one inverter paralle with itself? Pretty sure the bare minimum is 2 inverters working in paralelle...
Наука
I never received a dongle on my installation, great video. nice to see these quality videos
Hi Andy, thanks for the video. I can’t find battery code for N Power? Any idea what’s that?
Thanks Andy but it would be nice to go through each setting 1-20 with an off grid in mind
Another question our power is a bit wonky here in the Philippines. If AC isn’t properly grounded and I use the solar array to power up do I need to ground the inverter someway?
Hi Andy. What do I do when the bottom light on the LOGGER is solid and the middle one flashes for over a day now
and nothing else.
I have 9 x 450w panels producing 9,8A and 37,5V, what is the best setup for 2 of these invertors in parallel
does the SNA5000 need/support CT clamp/coil? if so how and where do i connect it?
Wooow I really like how in details you explain everything I wish we can be in communication
I've just bought one to be installed in Zimbabwe my question is will l be able to pair it with my mobile device since the professionals there don't have a number/reference from you? Thank you.
Hi Andy. Is Luxpower SNA 5kW inverter compatible with N energy 4 8kwh lithium ion battery ?
Hello sir..i am so glad i saw your video on this offgrid system..you mentioned that if it is first time to powerup a brand new inverter, battery shld not be used as power to wake up and setup the inverter. It shld be open thru ac supply..in my case the area has no grid present.what is the optiion if i may know..thank you
Hi Andy, are Greenrich battries compatible with Luxpower SNA5000
Very cool thanks looking to buy that in enverter
good day, how do you change from 50ah to 100ah as the dynesse is a 100ah battery
Hello, I hope you can clarify something for me. At the 5:10 part of the video you say you have a 50AH battery connected. Isn't the battery a 100AH battery?
The reason I am asking is that I have Dyness B3 batteries rated at 75AH each. However my lux power SNA5000 says its a 50AH (just like yours) When I add more B3 batteries it goes up at 50AH per battery as opposed to 75AH per battery.
I believe the SNA5000 has a 200AH battery limit.
I have 4 x B3 batteries and 2 x SNA5000 inverters.
I was told to parallel the batteries (300AH) and connect them to both the inverters at the same time.
I also want to parallel the inverters to a single phase . The webpage does not give me the option for paralleling that is shown in the manuals?
Is there a forum out there where I can get some assistance?
I have same issue. Greenwich U-5000 100Ah (Well, 96Ah I think) And the LUX Inverter shows 50Ah. I guess Firmware update time
Hi what do I use for the customer code to register on the app?
Hi Andy, great video. Does the SNA have basically the same functionality as the Sunsynk 5kw online hybrid?
No, it doesn't have CT coils and it can't power loads outside the EPS like the Sunsynk/Deye 5kw can.
What is the purpose of battery input? Considering i use it in n pure off grid. No DU at all
Hi Andy, I am struggling a bit with my dongle, the lights not going solid, the new app also doesn't allow me to find my WiFi connect...Can you pls assist
I have the same issue did you find a solution?
Thank for this. I did the unthinkable and reset the wifi thing to factory default. Could you perhaps share the UART settings? I am sure it defaulted the baud settings, so now it does not connect to the inverter
I read the following from my unit:
Uart programming setting > 115200, 8, None, 1, Disabled
Auto Framing > Disabled, 500, 1024
Hope this helps
Morning thanks for this information but how do I set it up using a iPhone
Does an off grid inverter need AC or can it work without ?
Hi Andy, How do I get in contact with you with regards to a Luxpower inverter settings
Hi. I have a problem with my invertor. The time keeps on changing. Can I contact you somewhere.
Thanks
Hi. I see there is a connection facility for a generator. Is there a place where one can set the charge rate for that port as to prevent charger overloading the generator?
So glad someone made this video. Just got the same setup. Exited to get it up and running. Can you maybe tell me how many 330w panels I can put on it. I see the voltage is 385
I got 2 inverters an 2 of the 4.8kwh Dyness batteries. I really hope you upload a video of how to install this system
It has a dual mppt. 3200w /tracker. I suggest you keep your solar to 2900w or less (per tracker) which allows for power spikes during bright cold days.
@@johnyjansenvanvuuren1980 Luxpower will upload a single phase parallel tutorial tomorrow.
Soon to be followed by the 3-phase parallel tutorial this week.
@@aspergo1648 thank you. Your videos helps allot.
Are you able to use the inverter to charge a never used before batter? When first setting up? I have the 10kw 200 a from meritsun
Hi Andy, I just installed my luxpower inverter with dyness battery, but it seems like it's not charging my battery
Please, explain how to use a generator for charging battery? I connected wires from generator to L and N to invertor. It doesn't work. Just trying to charge (i see on display) and disconnected. It is going again and again everytime. What is the problem? I have the same invertor and battery
Hi Andy. I have just installed our first Lux Power hybrid inverter. How do I get a customer code as an installer?
Same
use inf1 as a customer code
Good day, installed a Lux power inverter for one of my customers. We used a Elithium Battery. I do not know the brand value to use in order for the system to see my battery in setting 3. What should I do to determine the brand setting?
select acid battery and 100 amp it will work
E o bên nhật . Dien chi có 207v thôi. Zậy có cấp vao ac in duoc ko a
Hi Andy im having problem with my luxpower login app its saing network problem. but there is no network problem. Im from southafrica.
Hi Andy my LuxPower trips for a few seconds when the batteries are fully charged and the switches on again. Why is this? How do I fix.
can you explain pls how to enable the dongle again so i can connect to dongle hotspot. the problem is i set the dongle to station mode.i dont know how to access again to change to AP and Station
Hi, if the Dyness 48100 is a 100ah battery, why is the inverter displaying the capacity as 50ah? I have the same setup and its also displaying 50ah instead of 100ah.
Hi.
Did you manage to figure this out?
I also have two 100ah batteries (Greenrich) connected, but each it shows 50ah, and both in paralle it shows 100ah, and not 200ah
@@riaankoekemoer9035 Brett Franklin
2 months ago
do a firmware upgrade it will read 100ah. makes no difference though it will still operate the same.
Reply
tomsalmonandroid2
tomsalmonandroid2
1 second ago
I have same issue. Greenwich U-5000 100Ah (Well, 96Ah I think) And the LUX Inverter shows 50Ah. I guess Firmware update time
Good training
Не можу розібратись з налаштуваннями інвертора, спочатку поставив кислотні акб. Інвертор їх не заряджав по вольтажу, довелось ставити зарядку по часу, і виставляти щоб заряджав з 00:00 до 23:59 тоді запрацювало. Зараз купив літієву батарею asterion. В меню 20 брендів але не можу знайти рсошифровку чи ж мій у списку. І зараз при виборі на інверторі літжвої батареї він її взагалі не бачить
Great video thanks. What should the dip switch settings be when connecting to a Pylontech up5000 lithium battery, can’t seem to get them to connect
Where you able to get it right? Am struggling with that same issue now
Similar challenge guys, Pylontech 5000 lithium battery just can't connect. Please advise on solution 🙏 ...
There is a program/parameter fault with these inverters when it comes to battery setup/selection. Set to lead acid battery even if you are using a lithium battery otherwise you will not get comms.
@@antonvandenberg1461 ek het 'n 200Ah Osaka op ge sit en so proebeer. Maar my inverter charge nie die battery nie. Heeltemal te complicated vir my. Kan jy dalk help.
@@abrieolwage733 Hallo, ek neem aan jy het 4 Osaka battery in serie gekoppel. Maak net seker of jy die Gel of AGM batterye van hul het en stel jou inverter op met wat jou batterye match. Dan in die menu by charge times moet jy die waardes(tye) van 00:00-00:00 verander na 00:00-23:59
Hi Andy, my inverter trips quite often at my holiday house. Is it possible to reset it remotely through the app as we are 2 hours away . It has the dongle and i have the app on my phone. Can you possibly connect to my inverter to troubleshoot. Im prepared to pay for your time. Not sure if the battery has had its day. Its shoto lithium type.Thank you
10:32 the three lights do not flash green at this point. I waited a while. It only turns green after it’s connected to the wifi.
the lux power dongle can restore to factory default.i cant access the hotspot of the dongle. i set to station mode
Hello Andy
Have a lux power 5000 hybrid inverter with two elfbulb 100amp batteries and cannot get inverter to communicate and charge batteries Have set 03 lithium with setting 6 and other numbers but nothing maybe wire color coding on pin plugs into 485's ports.Please can you advise Many Thanks Regards .Love Your clips . Simple clear well done
Hello. A friend purchased LXP-5K Hybrid Inverters with Meritsun batteries. im trying to connect it to internet for remote monituring using application. but it requires a customer code, can you aid with that?
Hello Arap, can you please email info@luxpowertek.com so we can help you further, thank you!
Hi Andy, I have a 5kw S volt lifepo4 battery. Wich battery setting do I set? The manual does not give me a setting for this battery.
Hello, apologize for the late reply, do you know this battery has been compatiable with our inverter? if you have more questions, kindly send email to info@luxpowertek.com, we will help you to solve your problem, thanks
Hi,
How do I get a customer code?
I am an installer and want to register a plant
Hi Andy hope you are well I am struggling to register my Dogle USB it can not pick up my wifi even if I am close to my Router I have try everything I would like to deregister and start the hole proses from start plz help
Hi Andy video on setting please
Where can I buy this Inverter 🤔
Hi there, can someone answer my question please, if there is a video will be appreciated 🙏🏼Questions: If you turn off the power at main breaker and then back on does the inverter connect to the grid immediately?
Hi Sir, sorry for the late reply, if the SNA inverter is under on-grid mode when you turn off the main breaker, the inverter will be restarted to connect the grid in 30s. But if it is in other modes, prior to the grid connection being restarted, it's essential to fulfill the need for using AC in other modes; otherwise, the inverter will remain in off-grid mode. Hope this answer can help you.
Hi Andy I bought a similar lux power inverter But the inverter is failing to connect to a Hubble AM-2 5.5KW Battery please assist
There is a program/parameter error with these inverters. Set battery selection on inverter to lead acid, even if you are using a lithium battery otherwise there will be no comms
How do i disable the solar power exporting to the grid ?
Hi Andy, my data logger/wifi dongle will not switch on the "INV" LED. I have taken it out and put it back in but only the bottom two lights go on.
Were you able to fix this?
Also stuck here
Also stuck here
I got mine working via a laptop and the desktop site
@@brishenjaykaran4055 will try that thanks
I'm on this video because I didn't feel like reading the manual lol
Which setting is correct for a felicity 8,7 kw battery?
put acid battery and 100 amp it will work
My inverter is on battery full, but stop giving power, any ideas please
how do you change to a new hub code
I need the video on settings
I have connect the dongle. 3 light are stteady on by it shows offline on app
Well the inverter LED does not come on for me until after I have connected it to Wifi. Never has.
My dongle is broadcasting a ssd what do I do
My guy did not read the manual and I now need to get the app up and running. How do I do that?
Sorry Sir, we cannot understand your question well, could you please share us your SN and tell us the status of your inverter now?
Hi, how do I reset the dongle? Im not able to pickup the wifi network...
I have the same problem
Same problem
Mine says offline and cannot see it under wifi devices. 🙁
Приветствую
Ошибка внутренней связи 2
Не принимает с сети и не отдаёт в бекапе
Батарею показывает
Сеть показывает
Без сети пишет статус Нормал
Как появилась сеть сразу в ошибку падает в статусе!
Кто подскажет?
How i get a supplier code if my supplier doesn't have. Customer code?
Hello sir, is your supplier an installer or a distributor? If they are an installer, they can request their distributor to generate the code and provide it to you. If they are a distributor, they have the ability to create the code themselves.
Great product, absolutely SHOCKING after sales service. Your support tickets are just ignored.
please post link to shop wifi kit
LXP Hybrid 3-6k I don't have.
Hi Sir, thank you for contacting us, please let me know your city and we will provide you with the nearest distributor for your wifi kit.
@@LUXPOWERTEK Olbia Italy
@@GiovanniAnt Hi Sir, please contact our after-sale center in Italy for assistance, Davide
+39 0287159458
assistenza@luxpowertek.com
Got ot
But why at 5:00 your inverter detect accum as 50 Ah, if it is 100 Ah ?
Hi Sir, could you please share us with your inverter SN, we need to confirm your setting first. Thank you.
@@LUXPOWERTEK , I'm about your inverter on video, at time 5:00 ))
Why not just put all settings in the menu. On the inverter....
Hi, I am struggling to set solar charging batteries bcz batteries are only charging on Ac, when I connect solar panels only doesn't show charging, I am using luxpower inverter, 5 x545w panels, lithium battery,
Hi Sir, Apologize for the delay reply, I wonder that you wanna to set for PV charge priority, right? Please share us with your inverter SN, we will check your settings. Thanks
@@LUXPOWERTEK yes I need PV to be first priority to charge batteries
@@TitusMogane Hi Sir, For our SNA series, you can set the AC first working mode to achieve this function. In this mode, the AC will power the load first, and any excess power will be used to charge the battery.
Hope this reply can solve your question.
Sorry Sir, I forgot one setting on hybrid setting section, please also enable "PV & AC Take Load Jointly"
"Show you how to paralelle not one, but two machines. "- What am I watching ? , put one inverter paralle with itself? Pretty sure the bare minimum is 2 inverters working in paralelle...
🤡
When everything fails, read the manual, ZA style :P
Not for areas with no internet, dont buy this
THE MANUEL IS REALLY BAD ENGLISH ...USES LANGUAGE WHICH BEGINNERS CANT UNDERSTAND ... PLEASE MAKE A MANUAL IN PROPER ENGLISH
Howzit bro i installed a 5kva lux with 4x lead acid batteries its working fine but not charging the batteries what must i do