Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum
Hi Kalim! Thank you for your videos, they are very inrofmative. I try to fix error 2, this is my first expirience with repairing electronics, previously I have never used soldering iron at all=) First I changed shorted IGBT. Error 2 gone, but Error 3 appeared instead=) Next I changed failed resistor (it was black and burnt, I heard they often still works despite this, but not in my case). The same Error 3. After that I changed optical element inside speed sensor. Not working either. Error 3 appears after I press Start button (3 seconds later), motor not moving at all (but it actually works, electrician tested it). During starting, I can hear several times clicking sounds of relay. After upper console shows "error 3", at bottom console led "LED 6 CONNECT" turns off. What next should I try? Other transistors, resistors, capacitors, rectifiers looks good.
Hello friend, I have a problem with my treadmill. I would be grateful if you could give me your opinion on this matter. When I start the treadmill, the motor starts to turn off very quickly and then stops after about 4 seconds. There is no error code on the screen, the speed sensor is working, the mosfet is intact. Which parts do you think I should check?
Hi kalim i have a problem with a treadmill that shows no error on the board but... It starts normally but just when i change the speed the motor stops but the boads show that everything is working... Have you ever faced this case before
Hi Kalim, Hello everyone, good day. I have a problem in three control boards ,same model Life gear 97370M ,pressing start button gives 320 VDC to motor pin out terminals and it is non controlled, no up no down. I have tried many times ,tested MOSFET IRFP460 ,bridge and other components , nothing looks bad Can you help 10:58
Yes. I turn on the treadmill and after 3-4 second it starts to beep and on the screen appears E07. In the manual it says the safety key is not connected but on internet I found that the console Board is the problem...
A.a. sir mere pass running machine main fault ye aa raha hai k Kuch second chalne k bad reset ho jati hai Yani starting mode main aa jati hai.sir iska Hal batein
اخي الكريم.انا عند الجهاز هوم فيتنس.اول ماشغل عم يعطي e1.تم التشييك على الكبل بين لوحة السرعة والكرت.تم فحص 2فوتوكبلر.عل الكرت.جميع المنظمات سليمة.40n60igbtسليم.ومازال الكودe1قائم
मेरे पास एक बोर्ड हैं उसका problem hai ke आफ्टर लोड के बाद स्पीड कम होता हैं without lode chalta hai so kya karu power capcitor bhi chenge kiya so pl z help
Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum
Hi kalim i have a problem with a treadmill that shows no error on the board but... It starts normally but just when i change the speed the motor stops but the boads show that everything is working... Have you ever faced this case before
is this happen with any particular speed ? typically issue is related to feedback . sometime current sensing modules sends signals to the cards that motor is withdrawing more amperes.
Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum
Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum
Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum
Hi Kalim! Thank you for your videos, they are very inrofmative. I try to fix error 2, this is my first expirience with repairing electronics, previously I have never used soldering iron at all=) First I changed shorted IGBT. Error 2 gone, but Error 3 appeared instead=) Next I changed failed resistor (it was black and burnt, I heard they often still works despite this, but not in my case). The same Error 3. After that I changed optical element inside speed sensor. Not working either. Error 3 appears after I press Start button (3 seconds later), motor not moving at all (but it actually works, electrician tested it). During starting, I can hear several times clicking sounds of relay. After upper console shows "error 3", at bottom console led "LED 6 CONNECT" turns off.
What next should I try? Other transistors, resistors, capacitors, rectifiers looks good.
Hello friend how are you thanks for sharing
Thanks for this sir...
Plz sir share also AC drive repair video
Thank you for this video sir! It was very well done, excellant steps to determine the short in the circuit. Very helpful!
Hello friend, I have a problem with my treadmill. I would be grateful if you could give me your opinion on this matter. When I start the treadmill, the motor starts to turn off very quickly and then stops after about 4 seconds. There is no error code on the screen, the speed sensor is working, the mosfet is intact. Which parts do you think I should check?
good job friend
Thanks
Good information
Hi kalim i have a problem with a treadmill that shows no error on the board but... It starts normally but just when i change the speed the motor stops but the boads show that everything is working... Have you ever faced this case before
Hi Kalim,
Hello everyone, good day. I have a problem in three control boards ,same model Life gear 97370M ,pressing start button gives 320 VDC to motor pin out terminals and it is non controlled, no up no down. I have tried many times ,tested MOSFET IRFP460 ,bridge and other components , nothing looks bad
Can you help 10:58
Hello! I haver a treadmill Jet Stream with fault Err 2.I manual And nerd chance painel.Can you help me ?
Good video
Its motor has temperature sensor? How its work ? Plz
Assalamualaikum I want to ask the master if the energy riester treadmill hasn't been starred yet, it's E02
Good 👍
Hi dear. Help me please. My treadmill body strong in console show losc. How reset
Good
Thank u Moses
Hi. I have a problem with a EO7 errror. It says that i have to replace the console board. Can you help me?
Could you share me the details.
Yes. I turn on the treadmill and after 3-4 second it starts to beep and on the screen appears E07. In the manual it says the safety key is not connected but on internet I found that the console Board is the problem...
@@iloveheavymetal13 send me video at whatsapp +923009855546
I hope i will solve your problem.
I have uploaded 2 videos for error 7
Help me e 7 error
Sir why do tredmil increase speed on its own
What can be the reason by 60 amp transistor gets short after certain use ?
Rating of 60Amp is not for continuous use.
It can provide 10 amp max
A.a. sir mere pass running machine main fault ye aa raha hai k Kuch second chalne k bad reset ho jati hai Yani starting mode main aa jati hai.sir iska Hal batein
Assalam u Alaikum
How to fix E5 error in treadmill
I have E9 in machine active can you help me please?
Yes
Reples the 220 k hom restens
Sir ji meri dredmil me err2 aa raha hai
وين الشورت طلع اخي
Bhai jaan Hindi videos banaye
Please the name of parts u changed it in error 01
IGBT
اخي الكريم.انا عند الجهاز هوم فيتنس.اول ماشغل عم يعطي e1.تم التشييك على الكبل بين لوحة السرعة والكرت.تم فحص 2فوتوكبلر.عل الكرت.جميع المنظمات سليمة.40n60igbtسليم.ومازال الكودe1قائم
Bahi jan er 2 arha hai muje kia krna ho ga plz sir bta do
sir E3 eror kya app theek kr da ge...
Yes ho jayee gaa
@@KalimullahPakistan kis jga py hain app
@@marjancoolingcenter9328 Bharaku Islamabad
Madik maawatan
Error 4 why
मेरे पास एक बोर्ड हैं उसका problem hai ke आफ्टर लोड के बाद स्पीड कम होता हैं without lode chalta hai so kya karu power capcitor bhi chenge kiya so pl z help
Motor kay ampere check kro.
Motor jb ziyada ampere lati ho gi to circuit trip ho jata hoga.
Assalamu alaikum bhai my treadmill E0 fald kaise solve karoon
Its about safety key
Error 0
E 7 ERROR
Blis problem error4
Send video at +92 300 9855546
Hi bare call n
H
Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum
Hi kalim i have a problem with a treadmill that shows no error on the board but... It starts normally but just when i change the speed the motor stops but the boads show that everything is working... Have you ever faced this case before
is this happen with any particular speed ?
typically issue is related to feedback .
sometime current sensing modules sends signals to the cards that motor is withdrawing more amperes.
Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum
Assalamu Alaikum sir well Alhamdullah I am very happy to find this video I wanted a video like this Alhamdulillah I will start a job by watching this video Inshallah many more videos on the treadmill you hope Allah will reward you good Assalamu Alaikum