Thank you sir...I'm very much to hear from you...I normally watch the situation happening in your country. May you have life and continue blessing us with such technology...I've searched entire RUclips but there isn't much much detailed content like the way you provide
Is it possible to disable the 4GB RAM soldered on the motherboard so you can use a 32GB stick in the SODIMM slot? I'm currently using 20GB with a 16GB stick but it would be nice to upgrade to 32GB if possible. I think the max RAM is 32GB so 4GB on-board + 32GB stick = 36GB won't work. Right?
Sir this old video help me today to resolve ideapad 330s not triggering problem. Problem in this board is rtcvcc is okay on rtc diode but on rtcrst it's 1.4v instead of 3v. Track of rtc is internally leakage . After jumper from rtc diode to rtcrts resistor board start triggering. Thank you very much
sir is taraf ka cause mere paas aayatha hp i5 8th gen slp signals nahi mila io ko...even rsmrst# ok..maine ec bios ko programme kiya board ok hogaya...may bi ec bios i think not sure
Sir that replaced IC has a hole in it. I have a similar board with no lights nothing but 19v is present. Had a bad charger that caused the 330s to go off. Any suggestions plz? Checked mosfets and caps. Not found any shortage yet
Hello, I have an issue with the same PC and Motherboard. The PC suddenly stop working. I check the power voltage directly on the power connector (without to be connected to the motherboard) and I have well 19v. When I connect the connector to the mother and check the power value on the slot near the connector (+) I have only 0.4 v. No light is switching on. I did the test with another power supply: same issue. I removed the battery, RAM, disk... same thing Any idea? Thanks for your help.
Thank you sir...I'm very much to hear from you...I normally watch the situation happening in your country. May you have life and continue blessing us with such technology...I've searched entire RUclips but there isn't much much detailed content like the way you provide
Thanks brother 👍. Keep supporting and Sharing our videos 😊
In that case we faces firsly rtcrst, srtcrst and rtc frequency and also bios faulty, and there also fault of 3.3vdsw and rsmrst is generating?
Great work... Yes there are possibilities of these being faulty... Let's see what's the actual problem. By the way good attempt.😊👍
educational video again thank you sir.
Always welcome Brother 😊. And really appreciate your true feedback. Keep supporting and Sharing our videos 😊
sir i think need to check first RTC rail with cmos cell ....this is one of the cause that pch (soc) not generating s4 state
Great let's see what's the actual cause of this problem 👍
Is it possible to disable the 4GB RAM soldered on the motherboard so you can use a 32GB stick in the SODIMM slot?
I'm currently using 20GB with a 16GB stick but it would be nice to upgrade to 32GB if possible.
I think the max RAM is 32GB so 4GB on-board + 32GB stick = 36GB won't work. Right?
Yes possible if schematic and boardview is available.
What soldering iron u used sir?
You can see that in the video brother 👍
I add (RTC section and bios as mentioned before ) PCH PR enable
Okay let's see what could be problem...it's just a single case. There could be n number of solution for the same problem. By the way well tried.
Sir this old video help me today to resolve ideapad 330s not triggering problem. Problem in this board is rtcvcc is okay on rtc diode but on rtcrst it's 1.4v instead of 3v. Track of rtc is internally leakage . After jumper from rtc diode to rtcrts resistor board start triggering. Thank you very much
Great work bro. Keep supporting and sharing our videos.
sir is taraf ka cause mere paas aayatha hp i5 8th gen slp signals nahi mila io ko...even rsmrst# ok..maine ec bios ko programme kiya board ok hogaya...may bi ec bios i think not sure
Great experience sharing.... Let's see iss case me kya problem nikalta h.
Sir that replaced IC has a hole in it. I have a similar board with no lights nothing but 19v is present. Had a bad charger that caused the 330s to go off. Any suggestions plz? Checked mosfets and caps. Not found any shortage yet
Check properly the DCIN section and MOSFETs Gate switching.
@@laptex1377 Thank You
need a full class plz
WhatsApp
+919031240767
For details
Thoshiba c650 can change prossesor I have dual core can i change it pls rply
Better change the board will cost you lower.👍
Hi sir . thanks for sharing your knowledge.
in this case I Think :
1.RTC section
2.PCH Vcc standby
3.EC File Crashed If LPC Present (reprogram)
Good suggestion...these are most common opinion that is coming out now from our RUclips audience. Let's see what's the actual problem in this case.👍😊
@@laptex1377 atlist publish that solution? sir
great video sir, does suson signal go to other ICs
Why you going or jumping to suson first brother... could you please explain
@@laptex1377 i mistake,, suson signal for turning on enabling the ICs
1- rtc section
2- bios
Good attempt....we could be correct.but there could be other reasons as well👍😊
Hello, I have an issue with the same PC and Motherboard. The PC suddenly stop working. I check the power voltage directly on the power connector (without to be connected to the motherboard) and I have well 19v.
When I connect the connector to the mother and check the power value on the slot near the connector (+) I have only 0.4 v.
No light is switching on. I did the test with another power supply: same issue. I removed the battery, RAM, disk... same thing
Any idea? Thanks for your help.
There is shorting in the motherboard. Pls get it checked by local technician 👍
may be it has ram section problem, check vpp supply and powergood voltage.. it will be S5 Signal for VDDQ ram voltage and check vtt also
Good 👍
1.Rtc rst
2.srtc rst
3.rtc intruder
4 .rtc invermen....
Good 👍
❤️
Thanks 😊. Keep supporting and Sharing our videos ❤️
I think now u should check rtc section sir
Ok let's see what are the possibilities 😊👍
thanks sir ill leave a whats app an subscribe
Always welcome dear. Keep supporting and sharing our videos.
Cheak rtc section
Good 👍
1.Rtc_rst
2. Crystal
Good 👍
Crystal may be
Good 👍
I have the problem but sometimes its turning on properly
Try Check the concerned section.
Processer ki problem he sir CPU badlana hoga.
No it's not processor problem
I have same problem...🤕, pls help me...😔
Send motherboard to us we will check and update.
If RTC SECTION OK then I go for dpwrok,rsmrst
Good...👍
Eska schematic diagram milega
Search on vinafix available 👍
@@laptex1377 Thank You
I think all the pch signal have to chech.. ACpresent/ DNBS on/ DRAM RST/SuSclock..etc.
Great point. Will see what's the actual problem in this case.😊👍
Sir every time you upload half class video only you promoting already recorded class videos to make to mony for you.
Yes obviously we do... What's wrong in that. If you are interested bro you can join otherwise you can enjoy the free content on our channel. Thanks 😊👍
Enquiry ka Jawab tho detathu hai nahi
WhatsApp
9031240767
For details
plz tell us the actual reason
It's in paid case study videos bro.
bhai full content q nahi hai very bad filing
Everything can't be free... already mentioned hai ye paid case study mein aaega.
rsmrst 3.3v
Let's see what is the actual problem 👍
I wish I knew.
1. Flash bios chip with new firmware.
2. Check crystals
3. Call a friend and ask.
4. Buy new laptop
5. Google it the answer is bound to come as some other ppl have had same problem
Sure it's a possibility 👍
@@laptex1377 must be the crystal. Check it nex