EVINRUDE / JOHNSON 9.9HP AND 15HP CARBURETOR CLEANING, COMPRESSION TEST AND IMPELLER REPLACING
HTML-код
- Опубликовано: 30 окт 2021
- This video is made for people with no experience to be able to service their outboard motor in the easiest way.
2 stroke,
двутактов двигател,
двутактов двигател за лодка,
Outboard motor repair,
Riparimi i motorit jashtë,
Արտաքին շարժիչի վերանորոգում,
Xarici mühərrik təmiri,
Kanpoko motorren konponketa,
Рамонт падвесных матораў,
Popravka vanbrodskih motora,
Ремонт на извънбордов мотор,
Reparació de motors fora borda,
舷外机维修,
Riparazione di u mutore fora di bordu,
Popravak vanbrodskog motora,
Oprava přívěsného motoru,
Reparation af påhængsmotor,
Buitenboordmotor reparatie,
Päramootori remont,
Pag-aayos ng outboard engine,
Perämoottorin korjaus,
Réparation de moteur hors-bord,
Outboard motor reparaasje,
გარე ძრავის შეკეთება,
Reparatur von Außenbordmotoren,
Επισκευή εξωλέμβιου κινητήρα,
Reparasyon motè deyò,
Hoʻoponopono ʻenekini waho,
जहाज़ के बाहर इंजन की मरम्मत,
Outboard cav kho,
Külső motor javítás,
Viðgerð utanborðsvélar,
Perbaikan mesin tempel,
Deisiú inneall lasmuigh,
Riparazione del motore fuoribordo,
船外機の修理,
ಔಟ್ಬೋರ್ಡ್ ಎಂಜಿನ್ ದುರಸ್ತಿ,
Борттық қозғалтқышты жөндеу,
ការជួសជុលម៉ាស៊ីនខាងក្រៅ,
Gusana moteri yo hanze,
선외 엔진 수리,
Борттун моторун ремонттоо,
ການສ້ອມແປງເຄື່ອງຈັກນອກ,
Maiae filius engine reparatione,
Piekarināmo dzinēju remonts,
Užbortinio variklio remontas,
Outboard Motor Reparatur,
Поправка на надворешен мотор,
Fanamboarana maotera ivelany,
Pembaikan enjin sangkut,
ഔട്ട്ബോർഡ് എഞ്ചിൻ നന്നാക്കൽ,
Tiswija ta' magni outboard,
Te whakatika miihini o waho,
आउटबोर्ड इंजिन दुरुस्ती,
Reparasjon av påhengsmotor,
Naprawa silnika zaburtowego,
Reparação de motor de popa,
ਆਊਟਬੋਰਡ ਇੰਜਣ ਦੀ ਮੁਰੰਮਤ,
Reparatie motor exterior,
Ремонт подвесного двигателя,
Toe faaleleia afi afi,
Càradh einnsean outboard,
Поправка ванбродског мотора,
Tokiso ea enjene ea kantle,
Outboard injini kugadzirisa,
පිටත එන්ජින් අළුත්වැඩියා කිරීම,
Oprava prívesného motora,
Popravilo izvenkrmnega motorja,
Reparación de motores fuera de borda,
perbaikan mesin Outboard,
Ukarabati wa injini ya nje,
Reparation av utombordsmotor,
Таъмири муҳаррики берунӣ,
வெளிப்புற இயந்திர பழுது,
Тышкы двигательне ремонтлау,
అవుట్బోర్డ్ ఇంజిన్ మరమ్మత్తు,
ซ่อมเครื่องยนต์นอกเรือ,
Dıştan takma motor tamiri,
Daşky dwigateli abatlamak,
Ремонт підвісного двигуна,
Tashqi dvigatelni ta'mirlash,
Sửa chữa động cơ bên ngoài,
Atgyweirio injan allfwrdd,
Ukulungiswa kweenjini zangaphandle,
אָוטבאָאַרד מאָטאָר פאַרריכטן,
Ode engine titunṣe,
Ukulungiswa kwenjini yangaphandle,
funilaria,
Boat engine,
0386698 Carburetor Kit,
0398453 Carburetor Kit,
18-7223 Carburetor Kit,
0386149 FLOAT,
0396514 FLOAT,
0315232 Needle Valve Retainer,
18-7296-9 Retainer,
0386084 Impeller,
18-3050 Impeller,
0388289 Impeller Housing 9.9HP,
0435390 Impeller Housing 9.9HP,
18-3180 Water Pump Housing 9.9HP,
0435390 Impeller Housing 9.9HP,
0391571 Impeller Housing 15HP,
0388289 Impeller Housing 15HP,
0435390 Impeller Housing 15HP,
18-3180 Water Pump Housing 15HP,
0302497 Water Tube Grommet 9.9HP,
18-3329 Grommet 9.9HP,
0327035 Grommet 15HP,
18-2392 Grommet 15HP,
0319085 Impeller Housing Seal,
0318972 Seal,
18-2025 - Seal,
0326885 WATER RESTRICTOR 15HP,
0318995 Impeller Housing Plate,
0303794 Shift Rod Connector,
0324097 Impeller Housing Cup,
18-3179 Pump Cup,
0300611 Dowel,
18-3326 Pin,
0391638 Fuel Pump,
0395091 Fuel Pump,
0397274 Fuel Pump,
0397839 Fuel Pump,
18-7350 Fuel Pump,
0312634 Gasket,
0331363 Gasket,
0338876 Gasket,
18-2879-9 Gasket,
0329972 Fuel Pump Cap,
0312629 Fuel Pump Cap,
0323327 Cam Follower,
0323328 Cam Follower Roller,
Outboard motor tune up,
Johnson 9.9HP and 15HP outboard motor tune up,
Evinrude 9.9HP and 15HP outboard motor tune up, 
Хобби
Don't you just love it trying to get that wrench in there.i got tired of doing it that way about 30 years ago.i started pulling the starter
This video was extremely helpful, just cleaned my carb and reassembled. Without this video would’ve had no idea how to do it. My carb was slightly different with a fuel line inside the carb. Discovered that was my problem when I seen the whole in it. Needless to say swapped the fuel lines and proceeded to finish cleaning and put carb back together. Went from 20-30 pull starts and bogging out constantly to 4 pull starts and running great. Thank you for the video
Thanks!
Only bad thing is when you do a video talk say what you are doing thme you would get more likes and followers tho going so dam fast then I hear a plane tho you gotta explain a little bit tho just a fyi
@@donaldmartin4620 Thanks!
Nice job. Needing to replace the pump kit on my 1979 9.9 Evinrude.
www.ebay.com/itm/324444519684?hash=item4b8a667d04:g:8IsAAOSwK-xf9rHo&amdata=enc%3AAQAHAAAA4Op4j4%2B4hEF9V7IeGtNIJKrMuoASNHuZ1JtRgYqQ87PNn4jWDVSoXdvdHufT7d%2Fk64O170NbfKStAiY%2FrQpQzroh9OOEETBEfB%2BX9HIJLnVNJwGaFyTS99cCDpSvZca%2F96O%2B6qI6a0DEfL5D0L5lVRgC31dQRMz8a1hEcMnOglV73O%2FsbGesI%2FiyvBUBObWfiJQGVHJlsX3yror%2Bw66IOUhDG8ZK8nQ5pxNBubn6vBxogtZMHxh6XUQWv24ol9QyLEdBDtsbp%2FzJP0WSpGK9PoWhQ3UGqIAywVPi8dTrO4bs%7Ctkp%3ABFBMpLqFw_9g
Good Job
Wow nice job. Ñot a word said but I just learned a lot about my '76 15hp. Given to me with unknown condition.
Thanks!
For those that don’t want to remove the throttle to remove the carb. It’s much easier to remove the recoil starter by removing the center bolt. Then you have easy access to the carb mounting nuts.
Your Right, good Video but Torture watching him him take off carb screw jesus, REMOVE THE COIL The screw is right there, also after cleaning didn't clean the upper holes for slow idle again, go over every hole after cleaning
1978 By the look of the hood. Nice motor and job maintaining it 👍
Thanks!
@@BoatMotors They gave me a 1977 Evinrude 15hp, it runs like clockwork, but the throttle doesn't work: (((I can't understand why, if I had a magic wand I'd let you come here to see :)
Благодарю друже!
Thanks!
Tem que misturar com óleo 2 tempos?
Parabéns ótimo vedeo até me escrevi no canal.
Obrigado!
Nice video! I have a 79 15hp Johnny I can only get the throttle to about 1/4 😒 I've gone through carbs new plugs checked linkeage all free?
Check the throttle restrictor on the left side of the motor. When you switch to gear it must release full rotation on the magneto plate controlled by the throttle. Lubricate all linkages from handle to magneto including magneto plate plastic bearing. Thanks for subscribe to my channel!
De dónde son?
Olá Amigo muito boa esta aula de como limpar o carburador pois eu tenho um motor Johnson 15 Hp nota 10bpra você e assim eu vou Aprendendo agora só falava eu aprender com você a trocar a bomba de gasolina pois eu co.prei uma bomba nova ok Valeu obrigado
Me alegro de poder ayudar!
For the slow speed needle how far does it go in and adjustment
Slowly turn to the right the needle. At the end be careful don't force it. Then turn to the left one and half turns. Start the motor and slowly turn to the right to the moment when motor start sneezing. Then turn it very little to the left to the moment when the motor stop sneezing.
Thanks for the help!
What type of liquid do you use in the ultra sonic cleaner?
dawn degreaser
From all me research…the carburetor bowl float should be installed parallel/flat even to the bowl when looking from sideway?
Sometimes the float need to be adjusted. Yes must be installed parallel
@@BoatMotors
You got a new subscriber.
Please keep doing what you’re doing.
Thanks again!
@BoatMotors from you video its clearly seen that you bent it and left unparallel
Woah- what year was this- cork float makes me wonder?
Why wouldn’t you just put new plugs in?
From the beginning of 60's to the end of 70's pretty much all motors up to 20HP have an original factory installed cork floater. I replaced them with a plastic one, because with the time the resin over the cork starts to peel and can clog the carburetor jets.
Hello friend, I have a Johnson 15hp 2 stroke Model J10RCOM, to recover, I need its service manual, do you have it?
I don't sorry
is the 9.9 carb and 15 hp carb interchangeable?
Yes
if the impeller is at the bottom, does it spin at all when the gear is in neutral? Or is there another at the top?
The impeller spins all the time including in neutral gear
@@BoatMotors So the gearbox is in the bottom, then? How is it controlled?
@@kaapporaivio Yes. With the shifter.
The driveshaft turns anytime the motor is running. Since the impeller is keyed to the driveshaft , it also must turn, if it didn’t your motor would overheat if run in neutral. There are two gears,which face each other in the bottom bullet. The shift mechanism simply engages the pinion gear, (driven by the bottom spline on the driveshaft) with one of the bottom gears. One gear turns the prop forward, the other reverse@@kaapporaivio
What do I do if the tip of the needle is stuck inside of the carb ? I unscrewed the throttle adjustment screw at the top of the carb and the needle tip stayed inside
Realistically, this carburetor is beyond repair. I had the same situation a long time ago. With the thinnest bit possible, I drilled the tip of the needle into the carburetor. I sharpened the idle speed needle and the engine runs perfectly. I may have managed to fix it by accident... I don't know of anyone else doing something like this...
@@BoatMotors I somehow got it to come out . I took the smallest drill bit I had , stuck it beside it and used my drill to slowly to just continuously go around the tip . It eventually fell out and I didn’t leave a mark . But now I have the 2 pieces , and my motor will not run at idle . I can start it when it’s in forward drive and run it but as soon as I let off it dies . Is it due to this needle ?
@@lloydbauch8908 Yes
Eu tenho um carburador desse de 15 hp mais ele tá vazando ar pela parte branca essa parte de cima de parece ser de silicone como resolver esse problema amigo mim ajude ai
O meu motor é ano 79
www.amazon.com/Xinghai-0323327-Follower-Johnson-Evinrude/dp/B08TWQXN5K/ref=asc_df_B08TWQXN5K/?tag=hyprod-20&linkCode=df0&hvadid=507584275636&hvpos=&hvnetw=g&hvrand=7405999329607308702&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9029987&hvtargid=pla-1261056457342&psc=1
www.ebay.com/itm/171657747985
Can you tell me what compression should be o this engine. Thanks
160-140 Is new, 140-120 is used in good shape, 120-100 is still usable but much reduced proformance. And anything under 100 is bad.
@@BoatMotors my 9.9 had 60/70 closed butterfly and 70/80 wide open throttle and wouldnt suck fuel into the motor.. trying a re ring and cylinder hone..
Wish you could show more detail on how you removed the carb throttle. Your hands were in the way
Watch this video. ruclips.net/video/iGieCzK-Ctw/видео.html
Whats the best float setting for these 9.9s? Level?
You have to check the manual to get the exact numbers, but usually I can find the spot just by looking at it
I noticed yours was not level after you bent it with the pliers.
Yes not leveled
Boa noite, estou precisando da porca que prende o volante do motor de popa everude 15 Hp ano 82
www.marineengine.com/newparts/part_details.php?pnum=OMC0302944
Can you install the impeller backwards?
There is not up or down side. The impeller, rotation is clockwise. This is important.
Ola amigo, meu motor 15 ho do mesmo modelo desse seu , em alta velocidade escapa a alavanca que engata pra frente, como faço para regular ela?
No puedo entender. ¿Se está saliendo de marcha?
@@BoatMotors isso, ele desengata a marcha sozinho
@@valdineimotta3557 Você tem que desmontar a unidade inferior e encontrar o problema. Na maioria dos casos, é necessário um espaçador de arruela para compensar o desgaste da engrenagem
@@valdineimotta3557 Você tem que desmontar a unidade inferior e encontrar o problema. Na maioria dos casos, é necessário um espaçador de arruela para compensar o desgaste da engrenagem
@@BoatMotors valeu muito obrigado, vou desmontar aqui
MY JHONSON 15 HP ENGINE DOESN'T WANT TO HOLD AT IDLE OR START VERY EASILY WHAT COULD IT BE? I'M FROM BRAZIL
You need to clean the carburetor. ruclips.net/video/RGWVp_d0Iuw/видео.html
ruclips.net/video/GmGUMSuCmVk/видео.html
How much would this cost for a shop to do?
It all depends from the shop. Prices are from $100 to $250 per hour. All of this is 4 hours job.
Well, I learned a couple tricks. But, old shakey hands ... I'll still keep removing the starter first. Even then, I put a rag below to catch the nut I drop for the 4th time ... heh heh.
Check this video you can keep the starter together with clamp: ruclips.net/video/yIOZTfMarfk/видео.html
what spark plugs are you using
L77JC4 - Champion Spark Plug
Both those don’t have an electrode to adjust, can’t be a L77JC4 ?
I got the same motor. I have to. Keep pumping the fuel bulb, to keep it running. I am wait on a new fuel pump.
ruclips.net/video/WNvlLv9Ass8/видео.html
Ok now come do mine wow 😂😂 o have no idea mone needs a tuneup tho amd cleaned
Wie bitte???
Dont ever use Zip ties for gas lines!
Akways use LOCKTITE