I made one a while ago but made a mistake of using a ruler to mark the diatance of the holes and ended up being 1mm off. I like the little spacer block idea. I will have to remake it.
Beautiful Workmanship, The bearings, which were the 10 mm and which were the 12 mm, assuming that this is the O.D. of the bearings, could also tell us the size and lengths of the screws you used? Where did you purchase the red lock down handle screws. Thanks in advance
thank you 10mm bearings use 5mm bolts and 12mm bearings use 6mm bolts. A length of 20 mm is sufficient. I used 12mm because I didn't have enough 10mm bearings. You can use just one of any. The red knob is a 4mm bolt. All of these were purchased from Ali Express. It's been a while so no link, but you'll find it easily if you do a search.
After you set the stop on one side you could just turn the piece around 180 and drill the other end, no? It would be the same distance. I like the little bearing idea will definitely use that. Thanks
The method should ensure that the position of the center hole is in the exact center. It will take longer to verify that. So the way I showed you works more precisely. thanks
@@carpentak You already verified the spacing for drilling the first hole, you're just repeating the same process on the other side? Personally I think by doing a second move it just introduces another chance for something to move/shift. But you do what works for you.
@@Belg1970 Yes, I marked the first hole in the center. But I don't think it was exactly centered. I can't say that my tape measure is 100% accurate. Also, there may be very small errors in my central hole drilling process. So I think it's more accurate to work like that as I have shown.
Matias Lucena 28 de Junho de 2022 ativando o sino 954 aqui do Brasil e lhe dar parabéns pela construção destes marcadores bonitos e perfeitos, DEUS o abençoe.
Доброго. Молодец, хвастаться умеешь. Инструмент нефункциональный - не размечает до конца заготовки - видно по пробе. Хотя, нужно отдать должное - красиво, положить на полку, чтобы иногда полюбоваться. 😎
Сделали очень красиво, только самого главного не сделали - автоматический прижим карандаша! ;( Когда сделаете и попробуете, тогда сразу поймёте! Если карандаш будет "выперать" и проведёшь им линию, то может местами непрочертить, или сломаться грифель. В случае прижима карандаша пружиной, будет везде равномерный прижим! Но и это ещё не всё, в случае разметки толстого бруса (примерно от 20 мм и выше) то может потребоваться делить ширину на 2, 3, 4 .... части, то там нужна другая конструкция, где карандаш можно зафиксировать в любом месте между крайними направляющими. Таким образом можно делить на произвольное число, чего невозможно сделать в этой конструкции, хотя на ней использовали редкое и дорогое дерево :(
Very nice and beautiful indeed. But maybe a bit too much work about a little jig that can be simpler, and be made with a bit less effort and resources? Sorry about this little criticism.
Thanks for the comment. Of course, you can also simply make it quickly. But I wanted to make my own cool and special tools, and I put a lot of effort into showing them off in a video. I think that if I make a nice tool, my videos will be more interesting. Also, there are people who learn carpentry by watching the way they make and show work.
This video was very useful and interesting. I have a question. Where can you buy a pen like this? Can you send me a link from the website you bought it from? Thank you.
Thanks for the comment. I bought the pen from this site. However, it is only sold in Korea. You will probably find a place to order if you search by name. I know this pen is made in England. www.winextool.co.kr/m/product.html?branduid=1000007343&xcode=055&mcode=010&scode=006&type=X&sort=order&cur_code=055010&GfDT=bmx7W1U%3D
![[DIY] How to make a jig for cutting thin strips / Table saw project #8 / HOMEMADE](http://i.ytimg.com/vi/gDTRG1nA8yw/mqdefault.jpg)
As always ... beautiful work and clever idea. A real nice combination! Cheers ...
Cara kerja anda sangat menginspirasi aku,,,terimakasih sudah berbagi vidio ini
I really like that you are able to communicate without spoken language!
Very nice, as always. As elegant a walkthrough as the final product! Thank you for sharing this.
Una auténtica preciosidad, gracias por compartir!!! Really a beautifull tool, thank's for share your time and job!!
Nice job, can’t believe the number of brand new tools used in this demonstration, must have cost a fortune!
Saw Flamed Maple and Purple heart, suddenly thought you were making an Electric Guitar ! Great Vid
I made one a while ago but made a mistake of using a ruler to mark the diatance of the holes and ended up being 1mm off. I like the little spacer block idea. I will have to remake it.
Comme quoi,un outil peut être pratique et beau à la fois !👍👌
The second vid of yours I watched today, and I saved both for future projects.
Great job.
Excellent work!!!!! Where did you get the hardware from?
Also are there plans for this?
There is no plan.
I mainly buy from AliExpress. Thanks
I mainly buy from AliExpress. Thank you
absolutely impressive work!
Wunderbar. Ein edles Hilfsmittel, welches jede Werkstatt schmückt.
I enjoy watching you work. Yo can turn imple tools into th xt level tool. Great job
Excellent job will be a very useful tool,great video thank you
Happy to have found your channel. Thank you.
Brilliant.
I would have liked to be able to have dimensions a links to hardware used for these
Very nice work
Nice, I always test center finders by going the opposite way too (turn the center finder around). If I get two lines, then it is wrong.
incredibly clever as always. You need to come to New Zealand and teach me.
thank you. I also want to go to New Zealand and meet you.!! New Zealand is on my travel bucket list.
No bla-bla-bla, very good...
Beautiful Workmanship, The bearings, which were the 10 mm and which were the 12 mm, assuming that this is the O.D. of the bearings, could also tell us the size and lengths of the screws you used? Where did you purchase the red lock down handle screws. Thanks in advance
thank you 10mm bearings use 5mm bolts and 12mm bearings use 6mm bolts. A length of 20 mm is sufficient. I used 12mm because I didn't have enough 10mm bearings. You can use just one of any. The red knob is a 4mm bolt. All of these were purchased from Ali Express. It's been a while so no link, but you'll find it easily if you do a search.
@@carpentak Thank you for responding, that helps alot.
Good job. Congratulations 👌.
Thank you 😀.
Sympas... Cool.
After you set the stop on one side you could just turn the piece around 180 and drill the other end, no? It would be the same distance. I like the little bearing idea will definitely use that. Thanks
The method should ensure that the position of the center hole is in the exact center. It will take longer to verify that. So the way I showed you works more precisely. thanks
@@carpentak You already verified the spacing for drilling the first hole, you're just repeating the same process on the other side? Personally I think by doing a second move it just introduces another chance for something to move/shift. But you do what works for you.
@@Belg1970 Yes, I marked the first hole in the center. But I don't think it was exactly centered. I can't say that my tape measure is 100% accurate. Also, there may be very small errors in my central hole drilling process. So I think it's more accurate to work like that as I have shown.
Great job ... i love your way ... thanx alot my pro
Thank you for your valuable comments. I will continue to show you better videos. Please continue to be interested.
Bravo ! 👏👏👏🙏
very good
Matias Lucena 28 de Junho de 2022 ativando o sino 954 aqui do Brasil e lhe dar parabéns pela construção destes marcadores bonitos e perfeitos, DEUS o abençoe.
Turn on the captions :)
verry good
Tuyệt vời 👍👍
아주 멋지네요.. 근데 오일 바르시고, 하얀 걸루 문지르셨는데, 그 과정은 왜 하는지요? 그 하얀 건 솜인가요?
네 그과정은 폴리싱 작업입니다. 하얀 그건 폴리싱패드 라고 하는데 부드러운 수세비 같은거구요. 오일이 적당히 마른후 이렇게 문지르면 표면이 더 미끈해지고 촉감도 좋아집니다.
@@carpentak 그렇군요.. 덕분에 하나 또 배웠습니다. 감사합니다..
Доброго. Молодец, хвастаться умеешь. Инструмент нефункциональный - не размечает до конца заготовки - видно по пробе. Хотя, нужно отдать должное - красиво, положить на полку, чтобы иногда полюбоваться. 😎
Благодарю вас.
Шедеврально!!!
Adorei muito bom
Сделали очень красиво, только самого главного не сделали - автоматический прижим карандаша! ;(
Когда сделаете и попробуете, тогда сразу поймёте!
Если карандаш будет "выперать" и проведёшь им линию, то может местами непрочертить, или сломаться грифель.
В случае прижима карандаша пружиной, будет везде равномерный прижим!
Но и это ещё не всё, в случае разметки толстого бруса (примерно от 20 мм и выше) то может потребоваться делить ширину на 2, 3, 4 .... части, то там нужна другая конструкция, где карандаш можно зафиксировать в любом месте между крайними направляющими.
Таким образом можно делить на произвольное число, чего невозможно сделать в этой конструкции, хотя на ней использовали редкое и дорогое дерево :(
OK 👌
Very nice and beautiful indeed. But maybe a bit too much work about a little jig that can be simpler, and be made with a bit less effort and resources? Sorry about this little criticism.
Thanks for the comment. Of course, you can also simply make it quickly. But I wanted to make my own cool and special tools, and I put a lot of effort into showing them off in a video. I think that if I make a nice tool, my videos will be more interesting. Also, there are people who learn carpentry by watching the way they make and show work.
@@carpentak Fair enough! The video is definitely engaging, and the product is surely special and mouthwatering:)
This video was very useful and interesting. I have a question. Where can you buy a pen like this? Can you send me a link from the website you bought it from? Thank you.
Thanks for the comment. I bought the pen from this site. However, it is only sold in Korea. You will probably find a place to order if you search by name. I know this pen is made in England.
www.winextool.co.kr/m/product.html?branduid=1000007343&xcode=055&mcode=010&scode=006&type=X&sort=order&cur_code=055010&GfDT=bmx7W1U%3D
I believe that identical pencils are available from the various Amazons ... maybe not the exact same name, but same pencil.
Maravilha 👏👏👏👏👏👏
Полисандер и корельская береза?
퍼플하트와 메이플 입니다.
Okay!
👍👍👍👍👍👍👍👍👍👍
Hi how can i get of your making gauge
You must make it yourself. I made one and I don't sell it.
Ok👌
OKEEEEY
Зачем трогать рубанком когда есть рейсмус не понял
전동대패와 핸드대패의 차이를 이해하지 못했다는 것 같은데, 저는 섬세하고 정교한 작업에서는 핸드대패를 선호합니다. 그리고 부재가 얇거나 작을때도 핸드대패 사용합니다. 이것은 개인의 스타일에 따라 다른것이지 정해진 공식은 없습나다.
👌👍👍👍❤🌷
tu compliques les choses
rendre ce qui est trés banal est simple a qqchos de compliqué
Ok, ok,ok,ok,ok,ok,ok,ok,ok,ok,ok,ok,ok,ok...
:-)
Ok?..?.
I really disike video's with out commentry!