Mark Hosbach it’s a cracking idea but just watch the load on the drill motor, you don’t want to see smoke and dripping sealant coming from it like i did when using a sanding bobbin, expensive, needed new motor!
@@GC-rf2st I would think the side load on the bearing would be a bigger concern. They were not designed for it as much as for an axial load. If the motor is a concern like on a cheap drill press just use a lower speed belt setting.
@@InsideOfMyOwnMind You have to admit, it was a very efficient way of coating the sanding belt with glue at 7:15 It slowed down the sanding process so that he had more time to enjoy the work.
Also, hope you follow the driving rules e.g. use blinkers when making a turn, no speeding, etc.! It’s just that I’m tired of reiterating what you said, because I’ve professed the same thing (wear the same shoes as you). I guess it’s a COVID thing... people will do what they want to, no matter what! A coworker who worked on the Saturn 5 rocket, after screwing up (@ home) replied to his father, “but dad, I’m only human” & his dad replied, “unfortunately, son ...some people are more human than others “
@@SuperSpecialty I agree with your sensible comments on machine safety. However, anyone gullible enough to believe their TV rather than using their common sense in the real world is just wilfully ignorant, or, as Forrest Gump said "Stupid is, as stupid does."
Or a dremel, or a hand drill. Don't use wire brushes on bbq's either. Wires come off and get on food all the time. Buddy went to the er and they said it was very common
Some really good and creative ideas there... A few things to keep in mind though. Drill chucks and drill press spindle bearings are not designed to take side (cross axial) loads. The drum sander attachment is a very creative idea, and it clearly works, but I wouldn't use your drill press in that configuration exclusively as it'll greatly shorten the life of your spindle bearings. This is especially true of the inexpensive (cheap) bench top drill presses out there. The double drill chuck idea is fantastic... As a few others have commented, clamp a short length of steel rod in both chucks before tightening down the drill chuck on the drill press table. This will align the table chuck to the spindle chuck much more accurately, allowing you to drill concentric holes more accurately. Again... Some really creative ideas here, just keep the limitations of the machine in mind.
I've used mine for years with drum sanding bits attached to it. I haven't noticed any issues with the bearings wearing out and losing accuracy. You are correct however, the bearings aren't designed for lateral loads. If you think sanding is bad, I know a metal worker who couldn't afford a mill so he used his drill press. He bought a cheap chinese slide table and mounted it and used it for a couple of years until he saved enough for a mill.
Putting a bearing at the bottom and using the drum closest to that bearing takes a LOT of stress off the drill. I doubt very much it's even feeling any sideways pressure from that setup. I had something similar before I got a spindle sander. The only beef I have with it is I firmly believe dedicated tools is the way to go if you have enough room. Needing to set it up and take it down because I use the drill press for so many other things takes too much time for me. I bought that spindle sander years ago and I *still* think "this is so much nicer than setting up and taking down that drill press thing." But I should also say I gave the drill press spindle sander to another woodworker who then used it to death and built another one because he's short on room and put a planer where the spindle sander would have gone. So, there's that.
@@danc2234 The pressure would depend on what part of the spindle or drum you're sanding against. If you're using the top third, it would be more on the drill. If you're using the bottom, it'd be more on the bearing. It's not only space, it's $$. The cheapest spindle sander where I live go for $400.00. That's vs maybe what, $10 for this setup?
@@muskokamike127 Correct. There would be slightly more pressure as you went up, but the bottom bearing would still exert force against the push and no matter where the pressure is on the drum, the bearing would always make the force lines parallel with the shaft and not at an angle which would place enormous pressure on the shaft, bearings, and housing. I'm sorry spindle sanders are so expensive where you are. Harbor Freight's got em for 150. If that's too much, then yes of course the time it takes to set up and put away would be less important than spending the money.
#2: My Bosch drill press came with a fence very similar to this. A pair of them is no match for a decent vise though. If they are not clamped together, you risk pulling the workpiece upwards when releasing the handle, ruining whatever you are working on and possibly the drill bit as well. Always make sure that whatever you are working on is secured to the table. Safety first ladies and gents!
@@vinceblanchard1069 guess I should have known that since i have changed zillions of those i would not have thought of it though as i have a few always in my 'unsorted' lol used bolt can
This is SUPERB! I only have a little shed at the end of our garden but im slowly getting wood tools to convert my van into a camper. I have a table saw so far and loads of hand tools my Father left me. He was amazing at cabinet making and well....anything really. We lost him 2 years ago to the virus but hes taught me well. Your ideas will save me LOADS I wont have to buy a linisher or belt sander now. I also managed to score an antique drill press - but its built like a tank unlike modern ones! I use it with a moticing bit to cut slots its brilliant.
My favorite, was the drill chuck mounted to the table. I can use that technique to put a needle valve in the float bowl bolt, and have adjustable running mixture in my engines. I live at a high altitude, and all my engines run too rich. That drum sander has its possibilities as well. Great video, thanks for posting! All very good ideas.
This press has worked like a charm for my projects ruclips.net/user/postUgkxajoEbapTfqWaadnqb04h6U576yxXp-FE . I didn't even secure it to my table top, mainly due to the fact that I was using a 15 lbs drill vise. It's not flimsy at all as to what others have claimed it to be. Make sure the locking nuts and levers are secured and there won't be any issues with light pressure and patience. I was able to drill through aluminum, plastic, and steel (steel took a while) with no problems at all. Yeah it took a little longer than a regular drill press, but I don't have the space OR the money for one.The instruction manual was worthless, but luckily assembling the press was intuitive. However, the manual would be good for ordering replacement parts if needed. There is a nice breakdown of the parts that are included in the kit. Before ordering, make sure it is compatible with your unit, it is clearly stated what models the press is compatible with.This was an excellent purchase for $40!!
Chris 279 Ever realize that stuff that was invented in my early days or earlier is coming back as something brand new and amazing on some of these sponsor sites? Amazing!
If it really was amazing I'd subscribe, since none of it is................... He's at least thinking which is more than most seem to do today so that deserves a thumbs up.
@@arvinclassics I think he use pliers so the screw are not well tightened, therefore he can move the drill bit plate around easily... Amazing! ;p It was painful to watch I agree
Lost me with the first one. He used a centering bit (stationary) to drill about half an inch into a bolt (which was spinning in the chuck...) and it immediately went off center.
One of the best (in my opinion) and easiest upgrades you can do to these cheaper lightweight drill presses is to stick a small bottle jack under the front of it's table. Whenever you raise or lower the table just adjust the jack to snug up against the bottom of the table again. It takes all that flex out of it when you're putting a bit of force into drilling something, and it keeps the hole from going a few degrees off vertical.
The clamp on my drill press table is broken so I can't adjust the height very well. I was thinking of a bottle jack or a scissor jack underneath. Great minds think alike!
We just fixed are little 8" drill press today the drill head fell off my older brother thought it had to be epoxy back on, nope we used a sesser jack to press it on put a board under the aluminum table so we would not bend or crack it and press the head back on we have a bigger one the same thing happen to that one I'm guessing we have to do the same thing to that one? I didn't get to look at it only because it's buried in the shop and I can't get to it until brother clears out space in the shop.
Just found your channel. I love all the use of wood for making tools/jigs as my old go-to for 'scrap' metal place no longer pulls out the good stuff to sell 'retail'. Buying new steel is expensive,and I can always find wood around my historic district neighbor hood. People are always putting old wood out on the curb from homes that were built in the late 19th and early 20th century. One person's trash and all that.
Well that has to be a first! A video of "useful ideas" that are actually useful, and practical to make without a full machine shop and professional level skills. Thank you good sir!
An old 1970's Whitecote is what I use. Very, very heavy and so versatile - only £40 2nd hand - I had to fit a new starter, and it works like new. Would not waste my money on a flimsy modern thing like in the video.
The 'one on this vid' is a Ferm.. and though they make it well advertised as a brand, it is very poorly made. No bearings to support the spindle sleeve, so lateral play is huge. And the table flexes like crazy if you're drilling metal. There are locally made ones that are much better. Maybe this person uses it for hobby work. I made a mistake of buying it for our production woodworking team and it died a quick death.. in for warranty repairs now. Stay clear of it people.
Quiero ser el primero en felicitarle, ha demostrado usted una maestria encomiable, el profesional se nota rapido, pero el Artista es de otro estilo, se aprecia enseguida el disfrute en lo que uno hace, y usted ha disfrutado de corazón. Muchas felicidades Maestro.
Blown away by this guys creativity! This video will go into the archives for sure. Talking about serendipity,... I just bought my first drill press last week! The vertical sanding tool attachment is just brilliant!
All excellent uses for the drill press! May I ask what glue you use to secure the sand paper to the wood drum? It must be very secure, but also removable. Not sure what's glue is best. Hope you can tell me. Thanks much!
I did the second idea from your video but I also did a vertical slide mount on both l brackets as an added security measure to hold the part that I'm drilling tightly to the table. Awesome video as always 👏🏻👏🏻👍🏻 thank you for sharing and giving us more awesome ideas.
Get an older craftsman 150 dp from 1950 and search ebay for all the different attachments and different chucks they made for it and you can do all this and a lot more. Even take the head casting off, flip it upside down put it back on UNDER the table and stick a router bit in it and use it as a shaper...
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
I’m definitely gonna do the drum sander thing. Brilliant! Thanks
Thanks for appreciating my work...
Mark Hosbach it’s a cracking idea but just watch the load on the drill motor, you don’t want to see smoke and dripping sealant coming from it like i did when using a sanding bobbin, expensive, needed new motor!
That’s an awesome idea I’m doing that too!
@@GC-rf2st I would think the side load on the bearing would be a bigger concern. They were not designed for it as much as for an axial load. If the motor is a concern like on a cheap drill press just use a lower speed belt setting.
@@InsideOfMyOwnMind You have to admit, it was a very efficient way of coating the sanding belt with glue at 7:15 It slowed down the sanding process so that he had more time to enjoy the work.
When spinning a wire brush in a drill press, always wear eye, and preferably full face protection. I speak from experience, people.
Absolutely! Definitely a full face shield.
And a shirt preferably a thick one, experience not from a drill press but a angle grinder
Also, hope you follow the driving rules e.g. use blinkers when making a turn, no speeding, etc.! It’s just that I’m tired of reiterating what you said, because I’ve professed the same thing (wear the same shoes as you). I guess it’s a COVID thing... people will do what they want to, no matter what!
A coworker who worked on the Saturn 5 rocket, after screwing up (@ home) replied to his father, “but dad, I’m only human” & his dad replied, “unfortunately, son ...some people are more human than others “
@@SuperSpecialty I agree with your sensible comments on machine safety.
However, anyone gullible enough to believe their TV rather than using their common sense in the real world is just wilfully ignorant, or, as Forrest Gump said "Stupid is, as stupid does."
Or a dremel, or a hand drill. Don't use wire brushes on bbq's either. Wires come off and get on food all the time. Buddy went to the er and they said it was very common
Some really good and creative ideas there...
A few things to keep in mind though. Drill chucks and drill press spindle bearings are not designed to take side (cross axial) loads. The drum sander attachment is a very creative idea, and it clearly works, but I wouldn't use your drill press in that configuration exclusively as it'll greatly shorten the life of your spindle bearings. This is especially true of the inexpensive (cheap) bench top drill presses out there.
The double drill chuck idea is fantastic... As a few others have commented, clamp a short length of steel rod in both chucks before tightening down the drill chuck on the drill press table. This will align the table chuck to the spindle chuck much more accurately, allowing you to drill concentric holes more accurately.
Again... Some really creative ideas here, just keep the limitations of the machine in mind.
Thank you for giving such a nice feedback.
I've used mine for years with drum sanding bits attached to it. I haven't noticed any issues with the bearings wearing out and losing accuracy. You are correct however, the bearings aren't designed for lateral loads.
If you think sanding is bad, I know a metal worker who couldn't afford a mill so he used his drill press. He bought a cheap chinese slide table and mounted it and used it for a couple of years until he saved enough for a mill.
Putting a bearing at the bottom and using the drum closest to that bearing takes a LOT of stress off the drill. I doubt very much it's even feeling any sideways pressure from that setup. I had something similar before I got a spindle sander. The only beef I have with it is I firmly believe dedicated tools is the way to go if you have enough room. Needing to set it up and take it down because I use the drill press for so many other things takes too much time for me. I bought that spindle sander years ago and I *still* think "this is so much nicer than setting up and taking down that drill press thing." But I should also say I gave the drill press spindle sander to another woodworker who then used it to death and built another one because he's short on room and put a planer where the spindle sander would have gone. So, there's that.
@@danc2234 The pressure would depend on what part of the spindle or drum you're sanding against. If you're using the top third, it would be more on the drill. If you're using the bottom, it'd be more on the bearing.
It's not only space, it's $$. The cheapest spindle sander where I live go for $400.00. That's vs maybe what, $10 for this setup?
@@muskokamike127 Correct. There would be slightly more pressure as you went up, but the bottom bearing would still exert force against the push and no matter where the pressure is on the drum, the bearing would always make the force lines parallel with the shaft and not at an angle which would place enormous pressure on the shaft, bearings, and housing. I'm sorry spindle sanders are so expensive where you are. Harbor Freight's got em for 150. If that's too much, then yes of course the time it takes to set up and put away would be less important than spending the money.
#2: My Bosch drill press came with a fence very similar to this. A pair of them is no match for a decent vise though. If they are not clamped together, you risk pulling the workpiece upwards when releasing the handle, ruining whatever you are working on and possibly the drill bit as well.
Always make sure that whatever you are working on is secured to the table. Safety first ladies and gents!
I have so many drill press vises. It's like they follow me home or something.
Watched more than a couple of vids like this. Anyone know why I would want to drill a hoie down the center of a bolt?
Yeah, to make an oil filter adapter. If you know, you know😊
@@vinceblanchard1069 guess I should have known that since i have changed zillions of those i would not have thought of it though as i have a few always in my 'unsorted' lol used bolt can
@@doranmaxwell1755*facepalm*
This is SUPERB! I only have a little shed at the end of our garden but im slowly getting wood tools to convert my van into a camper. I have a table saw so far and loads of hand tools my Father left me. He was amazing at cabinet making and well....anything really. We lost him 2 years ago to the virus but hes taught me well. Your ideas will save me LOADS I wont have to buy a linisher or belt sander now. I also managed to score an antique drill press - but its built like a tank unlike modern ones! I use it with a moticing bit to cut slots its brilliant.
I have no idea why this video has any thumbs down. That's ridiculous. This video is great. I'm definitely building the sander this afternoon.
All diy videos should be like this...action speaks louder than words! It’s about the project, not the narcissistic individuals.
Bhai tu apna ek number ka desi woodworker hai !! Tuze sur tere skills ko naman 🙏🙏
My favorite, was the drill chuck mounted to the table. I can use that technique to put a needle valve in the float bowl bolt, and have adjustable running mixture in my engines. I live at a high altitude, and all my engines run too rich. That drum sander has its possibilities as well. Great video, thanks for posting! All very good ideas.
Hey, that's pretty smart... Did it work without leaking any fuel?
Appreciate the actual useful ideas and not garbage 👍
Thank you..
This press has worked like a charm for my projects ruclips.net/user/postUgkxajoEbapTfqWaadnqb04h6U576yxXp-FE . I didn't even secure it to my table top, mainly due to the fact that I was using a 15 lbs drill vise. It's not flimsy at all as to what others have claimed it to be. Make sure the locking nuts and levers are secured and there won't be any issues with light pressure and patience. I was able to drill through aluminum, plastic, and steel (steel took a while) with no problems at all. Yeah it took a little longer than a regular drill press, but I don't have the space OR the money for one.The instruction manual was worthless, but luckily assembling the press was intuitive. However, the manual would be good for ordering replacement parts if needed. There is a nice breakdown of the parts that are included in the kit. Before ordering, make sure it is compatible with your unit, it is clearly stated what models the press is compatible with.This was an excellent purchase for $40!!
9:35 for godsakes get a wrench
at 3:00 as well.
Who the hell has a bench drill before they have a set of spanners?
@@ibast1 A spanner.
Amazing and useful ways to tighten up your nuts on your amazing and useful ideas video. Use a spanner! 😳 OMG this ring end fits too! Amazing!
@@ibast1 same guy who wears namaste beads in the shop.
Anyone else realize the word “amazing” these days is just a euphemism for “click bait”
Chris 279 Ever realize that stuff that was invented in my early days or earlier is coming back as something brand new and amazing on some of these sponsor sites? Amazing!
A list of obvious modifications. He lost me by using a pair of pliers to 'tighten' the nuts.
If it really was amazing I'd subscribe, since none of it is................... He's at least thinking which is more than most seem to do today so that deserves a thumbs up.
@@arvinclassics I think he use pliers so the screw are not well tightened, therefore he can move the drill bit plate around easily... Amazing! ;p It was painful to watch I agree
Lost me with the first one. He used a centering bit (stationary) to drill about half an inch into a bolt (which was spinning in the chuck...) and it immediately went off center.
Great ideas!
I really appreciate your ingenuity and hard work!
😊😊
Keep it up!
One of the best (in my opinion) and easiest upgrades you can do to these cheaper lightweight drill presses is to stick a small bottle jack under the front of it's table. Whenever you raise or lower the table just adjust the jack to snug up against the bottom of the table again. It takes all that flex out of it when you're putting a bit of force into drilling something, and it keeps the hole from going a few degrees off vertical.
The clamp on my drill press table is broken so I can't adjust the height very well. I was thinking of a bottle jack or a scissor jack underneath. Great minds think alike!
We just fixed are little 8" drill press today the drill head fell off my older brother thought it had to be epoxy back on, nope we used a sesser jack to press it on put a board under the aluminum table so we would not bend or crack it and press the head back on we have a bigger one the same thing happen to that one I'm guessing we have to do the same thing to that one? I didn't get to look at it only because it's buried in the shop and I can't get to it until brother clears out space in the shop.
neat! i love the whole vertical lathe thing going on!
Just brought a pillar drill today and this video shows up on RUclips. Great idea's thanks
Just found your channel.
I love all the use of wood for making tools/jigs as my old go-to for 'scrap' metal place no longer pulls out the good stuff to sell 'retail'. Buying new steel is expensive,and I can always find wood around my historic district neighbor hood. People are always putting old wood out on the curb from homes that were built in the late 19th and early 20th century. One person's trash and all that.
Welcome aboard! Thank you...
The drum sander and wire brush ideas are excellent. Eye/face protection is definitely a must. Great video. Thanks.
Well that has to be a first! A video of "useful ideas" that are actually useful, and practical to make without a full machine shop and professional level skills. Thank you good sir!
I like the double Chuck method 👍🇬🇧
Yes me too. You could use it kind of like a mini lathe using files as tools.
One of the better Amazing videos on the Tube.
Thanks for sharing your video. I enjoyed watching. Take care and God Bless.
excellent ideas
number 1 was the best 👌👌👌
Thanks a lot 😊
Some great idea's for a drill press thanks !
Every once in a while I run across videos that deliver on the promise made in the title. This is one of them. Definitely worth watching! 👍
A drill press as a vertical lathe. Genius in its simplicity.
Great ideas, love these kind of videos, definitely will give your creative side a jump start, keep ‘em coming!
Amazing ideas. After watching this video I'm putting aside the idea of buying a lathe and sander.
I like the sacrificial insert in the drill press table, thank you
Flimsy drill press, the table bends under normal drilling pressure.
An old 1970's Whitecote is what I use. Very, very heavy and so versatile - only £40 2nd hand - I had to fit a new starter, and it works like new.
Would not waste my money on a flimsy modern thing like in the video.
The 'one on this vid' is a Ferm.. and though they make it well advertised as a brand, it is very poorly made. No bearings to support the spindle sleeve, so lateral play is huge. And the table flexes like crazy if you're drilling metal. There are locally made ones that are much better. Maybe this person uses it for hobby work. I made a mistake of buying it for our production woodworking team and it died a quick death.. in for warranty repairs now.
Stay clear of it people.
Comments seem to be pretty negative about everything but my man is at over a million views he’s got something going 👍👍
Seeing something done the wrong way over a million times doesn't make it good.
很實用的鑽頭架！最好能再加裝透明壓克力蓋子，以防不慎刮傷與防潮
感謝您的評論
Fantastic....i will do them all.. gonna start with number 5😁 thank you
Wonderful!
I dig it big time I am definitely going to do this. you sir either have one fancy shop or your shop is in your living room .....
Excellent ideas, thank you for showing this
You are so welcome!
Such nice workmanship...tightens hex nuts with a pair of pliers?
Great ideas. Definitely going to use the idea with the chuck in the base of the drill press.
This is just the kind of Engineering I'm into!
Молодец дружище. Толковые поделки, есть что для себя перенять.
many cool ideas! 👍
Isn’t this what drill press vises are for?
Yes, but i mean if you have some scrap angle iron laying around 🤷♂️ vices are cool but scraps are free
Great ideas for woodworking problems. There are videos on using a drill press for light metal milling too.
Great idea
The Jacob's chuck is actually neat!
I like the drill press sander. Oh and the Snoop Dog (like) soundtrack
Quiero ser el primero en felicitarle, ha demostrado usted una maestria encomiable, el profesional se nota rapido, pero el Artista es de otro estilo, se aprecia enseguida el disfrute en lo que uno hace, y usted ha disfrutado de corazón. Muchas felicidades Maestro.
Cool tips. I like the sander, good idea.
So you've got a drill press, hole saws, even a router, but not a 13mm spanner?
I got even better... a 1 ton milling machine. Does everything a drill press can do and then some...
I was thinking the same like wtf its only like 3 dollars and those drill bits cost more.
Absolutely BRILLIANT!
Why is that these days just about everything on RUclips is AMAZING?
going to use 4 of the 5. Thanks my dude, saved my cheapa$$ a few power tool expenses! Like & a sub fir your efforts
All those great power tools and no spanners ?
Fantastic tips for the pillar drill
Top man 👍👍👍
Thanks 👍
Credit where due, these are pretty clever and the film-making is notably better than average.
Very cool ideas 💡.
Glad you like them!
Thanks for the sharing.👍🍺👋
Thanks for watching!
The drum sander is a really good one. Thanks.
Thank you..
Liked the last one, may try it
Molto bello Bravo. Progetti molto interessanti. Fabrizio 🇮🇹 Iscritto.
Excellente!!! Una pregunta: Que marca de taladro y modelo es tu taladro que usaste??¡
Yep, lots of good ideas, I will do some of those, thanks.
Tools designers are so wonderful people
Thanks for the great idea's. We just fix our little 8 " drill press to day. 👍🏽
Loved everyone of those ideas! Thanks for the share!
You had me on the first tip bloody brilliant!
Blown away by this guys creativity! This video will go into the archives for sure. Talking about serendipity,... I just bought my first drill press last week! The vertical sanding tool attachment is just brilliant!
Awesome! Thank you!
What great ideas for a male 81 year young beginner woodworker
Glad you liked it!
Very clever ideas!!! Thank you so much!
I like it 😊👍❤️❤️❤️❤️
Very nice, thanks !
Smart idea I love it ! Thanks for sharing !
Very smart tips !!!
Thank you very much!!!
REALLY AMAZING AND USEFULL
THANKS A LOT FOR YOUR KIND TIPS
GOOD LUCK
Some great ideas. Love the bit holder.
Thanks so much! 😊
You did a great job. I commend you on all of your ideas.
Nice innovative and functional ideas. Thanks for sharing.
Lots of good ideas there.
Excellent demonstration and really cool tips! What diameter threaded rod and bearing do you recommend for the sanding drum? Thanks much.
Cool pleasantly surprised that most of these are very cool ideas. Especially the first two
Thanks...
You do know what that was don't you? It's a centre drill, to drill a small taper hole for your lathe centre/live centre. Never meant to drill a hole.
They should rename it "How to drill an off-center hole". The drum sander was awesome, tho.
Exelente vídeo... parabéns!!!
Grato pelas ideias!!!
thanks for sharing your ideas. lots of cool stuff here. love the double chuck!
All excellent uses for the drill press! May I ask what glue you use to secure the sand paper to the wood drum? It must be very secure, but also removable. Not sure what's glue is best. Hope you can tell me. Thanks much!
Glad you like that drill press hack. The glue which I used is epoxy adhesive and it is removable with little effort.
Love your channel
My life is going to change now I have watched this video👍👍👍👍🤓🤓⚙
Great and simple ideas! Thank you for posting.
I love the ideas in this video
Thank you
👍👍👍молодец, обязательно сделаю себе. Спасибо за инфу ✌✌✌
Nichevo :-)
You have lots of clever ideas here. A few suggestions if I may add. At 1:25 this will work better if turned around.
Very useful tips. Thanks
The vid gives you the idea, it is up to the viewer to use it to their advantage.
Idea #1 was my hand to forehead smacker.
Thanks.!
Drilling a deep hole with a centre drill 🤦♂️
What the hell is he making now!! A bit holder, LOL!! Excellent finish to video!
Great Ideas, TY!
I did the second idea from your video but I also did a vertical slide mount on both l brackets as an added security measure to hold the part that I'm drilling tightly to the table. Awesome video as always 👏🏻👏🏻👍🏻 thank you for sharing and giving us more awesome ideas.
Thanks for your nice suggestion..
Precision drilling not so much but your ideas are dead center. Thank you for sharing.
Title should read 5 Confusing and possibly useful ideas for a drill press machine.
I did not expect these to be so elaborate. I've used a DP for years and will be using these now. Thanks.
You've been DP'ed for years?! 😲
Get an older craftsman 150 dp from 1950 and search ebay for all the different attachments and different chucks they made for it and you can do all this and a lot more. Even take the head casting off, flip it upside down put it back on UNDER the table and stick a router bit in it and use it as a shaper...
#4 and #5 were pretty sweet