@@SilentPartner79well, maybe I should start making welding tutorials, but as a man who has taken welding classes for 4 years, I can tell you the way he taps the electrode to form a bead is something no good welding instructor teaches. In fact, if a construct failed because of a weld like this, the welder would be liable for any damages. The electrode angle was completely wrong, and wouldn't make any heat penetration when it's nearly parallel to the base metal like that. Beveling both sides of the joint caused more work than was necessary. In fact no beveling was ever needed to get full penetration. A simple adjustment to the joint was all that was ever needed, heck if he just turned up the amps and did a single weld properly on the joint the way it was probably would have been enough.
Been a welder/fitter over 10 years, this is a terrible weld. Undercut everywhere, rod angle was WAY off, 7018 would have been a much better choice over 6013, etc. sick of seeing all these 3rd world welding videos talking about secrets of welding when they don’t even know how to weld correctly in the first place.
Wash,weave welding, even for a cover pass, weakens the weld at the edges! Draws the material inwards, but the parent material won’t move, so it creates a high stress area! It’s gonna crack
Depends on what your building and how much presser the plates will have on them.if they are going to have a lot of weight against them then it was the right idea,but if not then it was over kill.
Больше всего мне понравилось как мастер сдувает шлак 😂😂😂 при такой манипуляции , можно остаться с ожогами на лице и хорошо если глаза останутся не вредимы
I’m not a welder but I work on steel boats on the ocean in Alaska. I’ve never seen a welder do this ever and that would draw confusion watching a welder try to do that wether it fab or repair. I’m sure if a welder were to do that in sny instance we would need him to weld he’d be fired on the spot.
вони коменти не читають :) Найважче заставити старого діда, "якийзавждитакварив", робити між пластинами щілини, адже так важче, деталь треба закріпити... А так зтулили докупи, присрали по-верху і так сойдьот - причому дійсно часто і таке з'єднання тримається, якщо нема значних навантажень
Dudes using a cutting wheel to grind a bevl that isn't even right anyway I would have been laughed at by my welding instructor for even showing him that
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
That would go down, faster then the titanic, when the inspector comes along
🙏👍
😂 so right
7018 would be my choice and for that much grinding I would be using a 9” grinder not a little toy 4” grinder.
🙏👍
Im not a welder but from what I know about welder comments on welding videos this is a terrible weld.
wow that's great guys, congratulations
I don't think I've ever seen a positive comment about a welding video. I would like to see those people weld something so I can see the difference.
@@SilentPartner79 thanks bro🙏👍
@@SilentPartner79
Many different techniques, most work just fine, this one is as good as any.
@@SilentPartner79well, maybe I should start making welding tutorials, but as a man who has taken welding classes for 4 years, I can tell you the way he taps the electrode to form a bead is something no good welding instructor teaches. In fact, if a construct failed because of a weld like this, the welder would be liable for any damages. The electrode angle was completely wrong, and wouldn't make any heat penetration when it's nearly parallel to the base metal like that. Beveling both sides of the joint caused more work than was necessary. In fact no beveling was ever needed to get full penetration. A simple adjustment to the joint was all that was ever needed, heck if he just turned up the amps and did a single weld properly on the joint the way it was probably would have been enough.
Been a welder/fitter over 10 years, this is a terrible weld. Undercut everywhere, rod angle was WAY off, 7018 would have been a much better choice over 6013, etc. sick of seeing all these 3rd world welding videos talking about secrets of welding when they don’t even know how to weld correctly in the first place.
👍
Probably a chinese
Действительно, много лишней работы
@@AWelding.🐎🦌
In the USA get a copy of the AWS D1.1 manual. A ton of pre-approved joints are in there.
🙏👍
Cutting disc to grind,lethal combination, Cutting disc will delamination and explode
Ok🙏👍
Wash,weave welding, even for a cover pass, weakens the weld at the edges! Draws the material inwards, but the parent material won’t move, so it creates a high stress area! It’s gonna crack
🙏👍
Millions of welders KNOW how to weld
🙏👍
But millions don't...
@Roger-ws8rj then they aren't welders...
Это конечно мечта для меня. Хоть бы похоже научиться варить.)
🙏🙏
It doesn’t look like bird droppings…
You got that much going on.
Keep practicing 👍
🙏🙏
Joints are usually strongest point I get the argument but seems like there would be better joiner options if your already cutting grinding hammering
👍🙏
Принцип правильный. Показоно правильно. В конце шва не очень получилось а так всё ок.
ok thanks
China welding vs everyone else
👍
Depends on what your building and how much presser the plates will have on them.if they are going to have a lot of weight against them then it was the right idea,but if not then it was over kill.
🙏👍
Больше всего мне понравилось как мастер сдувает шлак 😂😂😂 при такой манипуляции , можно остаться с ожогами на лице и хорошо если глаза останутся не вредимы
👍👍
И ты не один из этих людей, кто блять варит без фаски в упор в стык 😂
🙏👍
Я зайчиков наловил, пока смотрел
🙏👍
И потратил он всего лишь пачку электродов.
👍👍🙏
Если есть в кармане пачкаааа электрод,
Значит все не так уж плохо на сегодняшний дееень...
@@Max_Molotok... и билет на самолёт...)
I’m here just to let you know that every single qualified welder know how to prepare a piece with a proper bevel.
👍🙏🙏
@@AWelding. So why you said that only few people know that? Have you understood what I write?
@@lorenzoghinelli7018Probably click bate.
I’m not a welder but I work on steel boats on the ocean in Alaska. I’ve never seen a welder do this ever and that would draw confusion watching a welder try to do that wether it fab or repair. I’m sure if a welder were to do that in sny instance we would need him to weld he’d be fired on the spot.
👍🙏
Double bevel......😮
👍🙏
@@AWelding. Use a magnet to keep square, tack, then weld, always from right to left.... I'm retired sheet metal worker welder . I've done it all ....
@@richarddonegan4666 no have magnet
@@AWelding.If you weld you gotta have them to hold mild steel square...😮
@@richarddonegan4666 ok👍👍
7018 for multi and fill
👍👍👍
Dude is literally hate farming the welder community 😂
👍👍
@AWelding. Not saying anything about the weld, just the way the comment section is going.
Wouldn't it have been easier to juat bend the plate?
🙏👍
вони коменти не читають :) Найважче заставити старого діда, "якийзавждитакварив", робити між пластинами щілини, адже так важче, деталь треба закріпити... А так зтулили докупи, присрали по-верху і так сойдьот - причому дійсно часто і таке з'єднання тримається, якщо нема значних навантажень
A single bevel groove weld would be way better.
👍🙏
溶接の試験でやるから知らん訳ないですよ
🙏🙏
Хрень полная.
Все что нужно знать, это режим сварки.
Если тройкой варить десятку , и малым током, то и вот то что показали, это НАСРАНО.
🙏👍
Сам придумал, очень похоже на это. Если хотите это не академическая сварка.
🙏👍
Lol there no manipulation. Thats called laying a beed lol.
🙏👍
Holy shyt! 😂😂😂😂😂 fail fail fail fail
👍👍
Only a few huh? Clearly none here omg.!
👍👍🙏
Dudes using a cutting wheel to grind a bevl that isn't even right anyway I would have been laughed at by my welding instructor for even showing him that
👍🙏
Do the root with 6010/6013. Finish with 7014.
6013 👍👍👍
This is abysmal. Seek a different profession.
🙏🙏
素人だけど、盛り、また盛り大丈夫なんかな？
Sure👍
Отстой
👍🙏
Nope 👎
Ok👍👍
Why are you GRINDING with a cutting wheel?
👍👍
That's not welding,maybe a tacking
👍👍
What are you talking about? He burned up multiple rods on that a tacking would of used way less. Watch the whole video next time
Охуеть на один стык столько электродов
👍🙏
Lol bro you cant weld just scrap rhe whole RUclips channel and click bait skilled title idea. Lmfao 😂😂😂 yhis is comedy hope this js a pardoy weld vid
👍👍
전압이 넘 쌘거 같아~~~위빙도 좀 하수티나~~~ㅋ
Ok👍🙏