DIY Planer Restoration | ...Shop rebuild continued
HTML-код
- Опубликовано: 15 сен 2024
- **For more behind-the-scenes content and to support the channel: / hwdesigns **
The next step in rebuilding my shop comes in the form of restoring this circa 1985 15" Jet Planer.
She proved to be a bit more difficult and tedious than the jointer restoration that came before it, and I'm still not sure I trust her her fully - but this tune up is a great first step in getting my shop off the ground again ...both literally and figuratively.
I hope you enjoy!
To support "the show:"
- Like
- Subscribe
- "Ring the Bell"
- Follow me: / honestworkdesigns
Music Credits:
Up Here
Blue Steel
player.epidemi...
Smartface
Smartface
player.epidemi...
Bathtub
Ballpoint
player.epidemi...
Warren
Netzy
player.epidemi...
Vibe With Me
Kommodity
player.epidemi...
Smittten
Dylan Sitts
player.epidemi...
**Transcript of Voiceover
After it’s cross country journey, it’s finally time to restore this cira 1985 15” jet planer.
Let’s get into it
First things first, let’s get it off the floor
I decided on building a wide base frame out of 2x4’s
I cut the two legs at 20 degrees, and the upper cross beam at the width of the interior of the planer base cap.
Then drilled pilot holes and screwed them all together.
WIth both leg frames done, I simply braced them together with stretchers equalling the width of the planer base cap.
Next, time to get some of this weight off A) so we could eventually get it on the base and B) to make clean up a little easier and more thorough.
I started by disassembling the motor
And then working my way down
After getting a good bit of the weight off through removal of the motor, rollers, and gears, I turned to cleaning out the literal rats nest from underneath the table where the inset table rollers, and most of the cutter head lifting mechanisms are housed.
I used a degreaser to clean the old gunked up chain and hears,
And rust remover and a wire brush to tidy up the inset rollers
Before reapplying some oil to the gears and chain.
With the bottom all cleaned out,
I used the removable base cap to measure and mark the reliefs for the anchoring bolts.
Then used a 1 inch forstner bit to cut them out.
After that, it was time to finally get this thing off the floor
Okay muscles.
With the maching up, i turned to cleaning up all the pieces I had pulled out of it.
A combination of rust remover, wire brushing, rinsing and drying seemed to do the trick for most of them.
Of course the gears and chains run by the internal gearbox that turn the overhead rollers got a degreaser bath as well.
With all the smaller components in better shape, I turned to the rest of the machine.
I taped off the table rollers before adding rust remover to the cutter head to keep the gel from getting caught in hard to clean places.
After de-rusting the cutter head, I was able to remove the blades and componentry.
And I gave them individual rust removing baths as well, before reinstalling them into the cleaned cutter head
After that, I worked my way down the machine removing 30 years of rust and grime.
We also had to do a simple replace on the on/off switch after crushing the original in transport. Whoops. Thanks for the electrical help, Mr. HWD
With everything over head tidied up, I set about smoothing the table using tiered grips of sand paper
Then pressed on, removing the rust from the rest of the machine before starting to reinstall all of the cleaned up components.
I worked in reverse this time, bottom up!
Reinstalling the gears took an annoying combination of finesse and brute force to get things back into place.
But I was able to get it back and greased up again.
Before replacing the cover, I gave it a protective clear coat.
Then I turned to reinstalling the motor. It too, though not pictured, got a protective coating.
To get the belts back on, I first anchored the motor to it’s base, replaced the belts, then tighten their tension by lifting the motor and base with wedges before fully anchoring it in place.
After getting it place, I reconnected the wiring from the power source to the motor
With that, the machine was back in working order - time to get some wheels and beef up the base
To add more lateral stability, I added a few more cross beams.
Then to make it a little less top heavy, added some more lumber along the sides, and finally gave it a quick paint job.
The last step, once I was sure I wouldnt create any more debris, was to give the table a nice wax down.
And now, for the moment of truth!
On the docket for future projects, a table extension.
Until next time.
Great Job Congratulations
I like the way that you kept the original paint on it. Good job.
Thanks, David. I like the original look, plus - this was a “get it working, then put it to work” project. Haha! No beauty pageants for this one
Fair play, nothing seems to daunt you, I greatly admire your diligence. What an accomplished restoration, congratulations!🙂
Thanks so much, Jules! This project really kicked my butt - but I’m pumped to have this in my shop!
Congratulations! That is a boatload of work and you did it beautifully. I like the simple stand; I would not have thought of one like that.
Thanks, mark! It took a bit of trial and error to make it so the levering action didn’t split the base, but we got there haha
Nice!!
Thanks, Robert! 🙌🏻
Thank you for this amazing, informative video. I'm attempting a restoration of a similar model and your video has been an invaluable resource. Keep up the great work!
Glad it was helpful Kevin! Since this video, I’ve also taken apart the gear box to restore, so don’t hesitate to reach out if you find a question there!
Lovely restoration
These same planners were made under different brands, Delta, Jet, Woodtek, Grizzly and others. It’s the same base but with a different brand slapped on them. Great restoration, can’t wait to do mine.
Another fun video. I can't wait for you to get back to showing off your creativity on projects for your new home. Thanks for this video. Stay safe.
Thanks, Eddie. I can’t wait for it either! Haha! I’m getting a little tired of the necessary evil of these shop builds and upgrades - but it is giving me a new found respect and knowledge of these tools!
@@HonestWorkDesigns Don't get me wrong. I have enjoyed watching you restore the family tools that were passed on to you. The emphasis on family is a definite plus for me, but the main reason that I enjoy watching you is the unique creativity manifested in your projects plus to be entirely transparent....there is just something about your onscreen personality that is pleasing and attractive to me. RUclips is like that to me. I look for woodworking content presented by pleasant and appealing personalities. Stay safe. Ed
Aw, thanks Eddie! 🙌🏻
Nice vid. That FJ60 rocks!!!!!!!!
Been there, done that. With a Delta 15" instead of a Jet, but basically the same machine, after my basement workshop was flooded with 43" of water and mud. I took mine completely down, rollers, anti-kickback pawls and all. Took over a month of working evenings and weekends as the mood stuck. Nice job.
Great work as usual! and I love that land cruiser in the back
Thanks Logan!🙏🏼
nice restoration. But the base needs some kind of diagonal to stop the lateral movement.
It'll add a lot of stability.
Nice work.
Nicely done! Your making a very nice set of machinery💪😎
Thanks, Austin!
Super good job! You rock!!!!
No, you do, Peter! 🙌🏻
I would love to own a planner. Now I want to find one lol. Great video. Edited together perfect. You just got yourself another subscriber!
Thanks so much! I feel pretty lucky to have this hoss of a machine in my shop now! Just have to get used to this kind of power. Haha
👌amazing machine, good job 👏
Thanks, Miguel! It’s a beast!
Good episode. I'm really impressed that you were able to get it all back together without a basket of unused parts. (that's my go-to move)
I wish I had a sink in my garage too.
Thanks, Ron! I have to admit - there are three small washers I’m pretty sure go on the casing, but I had left over after putting it all back together! Haha!
Thank you for sharing this video. You are awesome!
I just got the same exact planer and was in great shape so I only cleaned it and fixed some minor issues.
You’re right about having to get used to that kind of power.😜
No, you are Herbert! 🙌🏻
This thing is such a tank, right?
Speaking of power what kind is it? 220?
Great job....I do have the same and have been planning to give it a good service...will follow your video....Thanks for it
Thanks, Robert! Not pictured were later gearbox tweaks too - I don’t pretend to be an expert, but don’t hesitate to reach out if you run into any hurdles. Happy to help people learn from my mistakes haha!
Might be a good idea to run some very fine sandpaper on the centrifugal switch inside the motor so they don't stick.
Fantastic job! All of my tools were purchased used, so I very much identify with you. Also, new sub!
Thanks so much, Phil! Kindred spirits! The effort on old tools is real, but man do they run like champs!
@@HonestWorkDesigns Couldn't agree more!
Awesome video!!!
I wouldn't know how to assemble/calibrate it after cleaning it lol.
Haha! I didn’t either really - just learned as I went!
@@HonestWorkDesigns very cool! Given the condition of the planr I'm sure it was waaay cheaper than a new model with the same specs.
Long ago a friend stressed that I should wear steel capped boots when working on machines. I only took his advise seriously after a 22kg motor slipped from my hands and fractured my big toe's distal phalanx.
very good job i have a identical one brand name king Canada does anyone know where to get parts I need some bushings cheers
Thank you for the video. I have a question. I recently acquired the same planer. When turning the wheel to raise the height, it takes 2 hands with a lot of strength. Why would this be? The 2 lock knobs are unlocked. Thx you
Great work. But two things: 1. Why didn't you sharpen the blades? 2. Is the round raising wheel thing supposed to be as wonky as that? Surely not. Otherwise we'll done, you've taken something crap and old and made it useful in the world.
Thanks, Luke! After getting them de-rusted, and knowing the back story that they only ever met a board or two before my dad put these machines up, I realized they were still really nice and sharp. I got a few cuts on my knuckles while putting it all back together to prove it! Haha! And my dad is to blame for the wonky wheel, but since it didn’t affect the function, something in me just couldn’t remove the “character” he left behind haha!
I kept waiting for you to fix the off kilter height adjustment wheel.
Haha - I really thought about it. But my dad gave it that wobble (on accident) when he was using those tools - felt wrong (because it also doesn’t affect the function) to take that story away. Haha!
Great video, but please put on some steel-toed work boots.
you where really playing with fire with the bolts in the sink
I just bought the floor model version of this (took my back unloading it and then 5 grown men to move it) it’s just missing the outfeed rollers.
Mine has this issue that the lock for the thickness /platform elevation is not locking into place plus I don’t think the previous owner cleaned it a lot.
Really tempted to do the same you did tho.
Do you have any input into the aforementioned lock knob issue before I just go to town?
Well, that was a lot of work! I am sure you learnt a lot about your planer. After all that cleaning and reassembly, I really am impressed with your end result.
Would you consider diagonal bracing to control racking of the base? Or isn’t it necessary? The bent winder - is it the handle or the shaft? Worth fixing with the judicious application of heat or does it add “character”? Anyway, well done - time for a rest on your laurels.
Thanks, Alan! It really was, I don’t know if you can tell by the video, but this project really took it out of me! Re the racking, I think in theory it wouldn’t be the end all be all since the machine doesn’t create a lot of lateral motion, but I think when I add table extension, i might put something in there to just be over cautious. As far as the wonky wheel, my dad put that “unique” shaping in there in his own shop accident. Something about that back story (plus it doesn’t affect the function) made me wan to keep it a little off kilter :)
HonestWork Designs ah, the wonky wheel has a family history link attached - keep it.... It looked like a lot of work and I noticed concentration and focus which is entirely appropriate for a task like that. Have a rest on your verandah with a cool drink and have one for me.
As to the possible racking of your stand, I was thinking more about when you’re pushing it around in the medium term, it might rack sideways a bit against dust and debris on the floor.
Cheers to that, Alan!
Honestly good video though I cringed at the sandals, garages and tools call for closed toe shoes at the very least. Also safety glasses should have been warn during most of the tasks.
What was the model number?
Como consrguir las rrefacciones
Prius
Are you married 😳.
Nice refurbishing
So you cleaned it and flushed all the grease and heavy chemicals you used down the drain? Ok
She ate a burger while at it too. That meat came from a cow that farted.
Pretty lady with a Pretty voice doing man things and being skilled at restorations. Marry me, you don't even have to cook.