If you put your end cap back on then your seeds wouldn't just fall out the end. Plus your flame is to hot it is making your cake come out to stiff. But great automation. I think if you move your wheel and sprocket closer it wont bend your press so badly. Your cake should be coming out the two small holes at the end of the shaft by where the adjustment plug goes but it can't because you forgot to put in your end plug. Just some thoughts. If you put in your end adjustment plug you also wont have to hammer out the cake at the end of you session.
Nice setup! I thinking of doing the same but mounting a Bicycle, and removing the front tire? Then when done remove the bike, and install the front wheel mean of Transportation.
Kedves Fenyutas! 5 év telt el az első próba óta, működik még a prés? Milyen gyakran és mire használta? Mennyire elégedett vele? Ha ideje engedi, kérem ossza meg tapasztalatait. Köszönettel: Arnold
Last month, I purchased (manual) one on Amazon. I had to buy a thick block of wood to mount it. It did not come with any mounting accessories. So I had buy a thick block of wood for that purpose. That was the only drawback. I had my first test with Sesame seeds and Successfully pressed oil. I can see the difference between store brought and this oil. For some reason, the cake became very hard at the end of the press ( after pressing 250 gm) and it was not coming out of the outlets. I did not understand the reason and stated looking for messages if someone experienced the same and the how they fixed it. Someone said it the flame is too hot, the cake becomes too hard. Let me know your thoughts. Thank you.
yea, they say you dont need to heat it if the seeds are at room temperature. Maybe some oils are too thick but then again people seem unable to adjust the wick these days
I've read on some medical websites that the best oil extraction is after the seeds have been roasted to 100 degrees Celsius (about 210 F) for no more than 10 minutes and then pressed. The purpose is for best the oil yield - here's a pull from NIH: The different thermal processing protocols yielded three distinct patterns: heating the Nigella Sativa seeds to 50°C, 100°C, or 150°C produced oil with a strong ability to inhibit tumor cell growth; no heating or heating to 25°C had a mild antiproliferative effect; and heating to 200°C or 250°C had no effect. Similar patterns were obtained for the thymoquinone content of the corresponding oils, which showed an excellent correlation with the antiproliferative data. It is proposed that there is an oxidative transition mechanism between quinones after controlled thermal processing of the seeds. While NS oil from heated seeds delayed the expression of NF-κB transcription, non-heated seeds resulted in only 50% inhibition. The data indicate that controlled thermal processing of NS seeds (at 50°C-150°C) produces significantly higher anticancer activity associated with a higher thymoquinone oil content, and inhibits the NF-κB signaling pathway.
I am interested in building oil screw press for soybean Seed,Groundnut,and Palm kernel. The press should be able to press 50kg of the above mentioned material in an hour. What are the specifications necessary to meet my need.
You feed the seeds through whole (not shelled). The lamp warms the press. He has the flame too high, though. You shouldn't have the black smoke & black residue on the press. He needs less wick sticking up.
Hello! If possible, could you please tell me the proportions? It looks to me it was about 1.5 kg of seeds to something around 200ml of oil, is more or less this?
Хобби
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
Nothing like watching the grass grow...
If you put your end cap back on then your seeds wouldn't just fall out the end. Plus your flame is to hot it is making your cake come out to stiff. But great automation. I think if you move your wheel and sprocket closer it wont bend your press so badly. Your cake should be coming out the two small holes at the end of the shaft by where the adjustment plug goes but it can't because you forgot to put in your end plug. Just some thoughts. If you put in your end adjustment plug you also wont have to hammer out the cake at the end of you session.
Nice setup! I thinking of doing the same but mounting a Bicycle, and removing the front tire? Then when done remove the bike, and install the front wheel mean of Transportation.
الله يعطيك العافيه لكن عندي ملاحظه... ألغى المنويل وضع المسنين مباشر على إكس الحلزون ولا داعي للجنزير والمنويل
You can directly connect the shaft to the wheel buddy... Thank me later!!!
Kedves Fenyutas!
5 év telt el az első próba óta, működik még a prés? Milyen gyakran és mire használta? Mennyire elégedett vele? Ha ideje engedi, kérem ossza meg tapasztalatait.
Köszönettel: Arnold
Last month, I purchased (manual) one on Amazon. I had to buy a thick block of wood to mount it. It did not come with any mounting accessories. So I had buy a thick block of wood for that purpose. That was the only drawback. I had my first test with Sesame seeds and Successfully pressed oil. I can see the difference between store brought and this oil. For some reason, the cake became very hard at the end of the press ( after pressing 250 gm) and it was not coming out of the outlets. I did not understand the reason and stated looking for messages if someone experienced the same and the how they fixed it. Someone said it the flame is too hot, the cake becomes too hard. Let me know your thoughts. Thank you.
Did I just see petrol in that bottle? BOOM!
Jól látom napraforgómag a héjával együtt volt sajtolva? Lehet hogy azért ment ilyen nehezen?
Como hacer aceite de oliva? Por favor un video, gracias
Heated oil is sold on stores . Idea of making it yourself is to get COLD EXTRACTOR.
yea, they say you dont need to heat it if the seeds are at room temperature. Maybe some oils are too thick but then again people seem unable to adjust the wick these days
I guess the motor washing machine motor you use. The speed of the washing machine motor is too high. Can you tell us how you managed to reduce it?
Is the the oil lamp necessary? Wouldn't the heat destroy the oil and cause it to go rancid? Compromising the integrity of the oil being produced?
It's lamp or edible oil. It's 50-60 C while working. Destroyed??? Perhaps...
UNDIQUE01 кулибин👍
I've read on some medical websites that the best oil extraction is after the seeds have been roasted to 100 degrees Celsius (about 210 F) for no more than 10 minutes and then pressed. The purpose is for best the oil yield - here's a pull from NIH: The different thermal processing protocols yielded three distinct patterns: heating the Nigella Sativa seeds to 50°C, 100°C, or 150°C produced oil with a strong ability to inhibit tumor cell growth; no heating or heating to 25°C had a mild antiproliferative effect; and heating to 200°C or 250°C had no effect. Similar patterns were obtained for the thymoquinone content of the corresponding oils, which showed an excellent correlation with the antiproliferative data. It is proposed that there is an oxidative transition mechanism between quinones after controlled thermal processing of the seeds. While NS oil from heated seeds delayed the expression of NF-κB transcription, non-heated seeds resulted in only 50% inhibition. The data indicate that controlled thermal processing of NS seeds (at 50°C-150°C) produces significantly higher anticancer activity associated with a higher thymoquinone oil content, and inhibits the NF-κB signaling pathway.
🤔 naja...
Hi,, Sir,Can i use a 200 watt ac motor instead of handle to expell the oil? Plz answer me.
Did you try it ?
I am interested in building oil screw press for soybean Seed,Groundnut,and Palm kernel. The press
should be able to press 50kg of the above mentioned material in an hour. What are the specifications necessary to meet my need.
This machine too little for you. You need a bigger one. The exact specifications of this machine on the PITEBA site.
It was like watching mr bean. Sorry, nice contraption though.
What was the kerosene lamp for? Did you shell the sunflower seeds first?
You feed the seeds through whole (not shelled). The lamp warms the press. He has the flame too high, though. You shouldn't have the black smoke & black residue on the press. He needs less wick sticking up.
You're cool! don't get out of hand at all!
It's a 17th century's way😏
اين تباع هذي الالة في الجزائر
hot pressed? :) the flame was way to high
Can it used for other product as Sisma seeds & other?please answer me
Hi, sorry I don't understand "sisma", but naturally it's usable to other oilseeds. The point is to have oil content. Have a nice day!
Hmm flame -- hot,like your power drive ,good innovation
Very innovative 👍 oil mill
Say something godammit!
Him: 6:21
:D
🤙😂
me gusto mucho pero el sistema de la manivela es un poco forsoza. la pieza se mueve mucho
A lot of work for little bit of oil
Hello! If possible, could you please tell me the proportions? It looks to me it was about 1.5 kg of seeds to something around 200ml of oil, is more or less this?
+kerplunkboy Please see all exact proportions on piteba.com
Thank you brother
Good idea पण हॅन्डल la साखळी लावण्या पेक्षा सरळ सायकल che चाकाला फिरणारा rod जोडला पाहिजे
🇵🇰👍very good .U not watch hole last Wal swcuit and how press beens
These are currently available on Amazon and ebay
It is a very Nice Video.
omg! you must support the back of the press, the friction of the metal gets lazy and can break!!!
How much litres oil do you produce ?from 5 kg of seeds
About 1l sunflower seed give 1dl oil. My mechanical drive give 1dl/15min.
Fenyutas 1dl stand for?
Not from 1kg, but 1 litre!
what is the engine you use it
It's an engine of a washing machine.
Meu sonho ter uma dessas 🥰
kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk
@@syl_fonseca902não intendi a graça....
Good Try. Hope you will improve it.
Good job!
what is capacity ?
About 1l sunflower seed give 1dl oil. My mechanical drive give 1dl/15min.
egy teljesen értelmetlen meghajtással
Very nice!!!
I need this
price??
See here: www.piteba.com/nl/
That thing is about as stable as the Millennium Tower in SF. Ya, I think I'll buy my oil.
first I thought he uses it to roast the seeds
good.
super
1932 technology at best.
Personne ne c' est ou il y a mise son doigt avant 😝
Boa noite,
Onde posso comprar uma máquina dessas, extratora de Óleos ?
Essa máquina também extrai óleo de côco ?
piteba
Nice try
The gadget makes machine work too slow
very nice :)
Aidez-moi, il est vraiment bête ou il le fait exprès?! :p
je crois plutôt qu'il joue au professeur tournesol....
по моему полная хрень, "холодный" отжим?
Bahut sunder
Najlepiej użyć wiertarki akumulatorowej do wyczyszczenia tej końcówki
От жадности спалил пресс
kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk
Queimou o dedinho ne??? kkkkk
Kolkata me kaha milega details bolega ? Details address aur phone number dijie.
oauuuu
terrible contaminated oil. hope u are not seling this. please, do not give to your family.
I give omega 3 oil to my cats. Please dont give your oil to anyone.
sofiane sellam so am i!
@@demonincabare4337 why is the oil contaminated?
Wow contaminated oil really? Who are you, have you heard of hexane extraction? This video is awesome
ridicol
Nem bíznék benned semmiben.