4:28 on my joystick at home, i only find these "GND, VCC, VRx, VRy, SW" - But on the photo/schematic, it says Lx and Ly? What should i do, if Lx and Ly isnt a option on my joystick?
When I try to configure the HC-05 and try to input the AT commands to assign slave/master, I am being met with "ERROR (0)" in the serial monitor terminal. Do you know how to fix this issue?
What is the maximum distance the car can move away from the remote controller so as not to lose the connection? For me it is 2 or even meters. Also I lose connection when I direct the remote to the other side of the car.
i am trying to apply this project, in the first step of putting the HC-05 in A T mode, it is turning only red light instead of red and blue light, what should i do in this case? Note: i am using Arduino Pro micro
@@aslamhossain1 i already did this step but it is blinking with red only, also when i trying to send the A T command lines to the serial monitor, but nothing appear in the serial monitor
@@ربابآلسهوان I am also getting this issue but when I type the commands into the serial monitor, I am getting some symbols which usually show up if the serial number I am using is incorrect but I am using 9600. Not sure what the issue is with it.
The HC05 master doesn’t seem to be retaining the role change to 1 but says ok to all steps but the two HC05 don’t seem to connect to each other after completing all the steps
@@aslamhossain1 Did you have any issues with the L298N? When I test it with one side it works fairly fast, when I do it with both sides sometimes I have to give it a little manual turn to start it up and its very slow but a lot of the time it is just not turning. I am not sure whether or not it is a power issue or what. The wiring seems to be perfectly fine.
I just tried everything but my motors are moving uncontrolled all the time and they are changing directions for just a sec also. Do you have a solution for this?
i have a problem, when my car just started, it runs normally but after that i can't controller, i press reset button on arduino board and it back to normal how can i fix that
@@aslamhossain1 আচ্ছা এই টিউটোরিয়ালে আপনি রিমোটের বেলায় জয়স্টিক দুটার ক্ষেত্রেই x, y দুটাই ব্যবহার করলেন যে? আমার জানামতে এখানে একটা জয়স্টিক শুধুমাত্র x অক্ষে এবং অন্যটা শুধুমাত্র y অক্ষে কাজ করে। তাইলে একটারই দুইটা x,y নিলেন যে?
𝐂𝐢𝐫𝐜𝐮𝐢𝐭 𝐃𝐢𝐚𝐠𝐫𝐚𝐦 𝐚𝐧𝐝 𝐂𝐨𝐝𝐞:
github.com/aslam-Hossain-YT/Joystick-Control-Bluetooth-Car
Thanks
4:28 on my joystick at home, i only find these "GND, VCC, VRx, VRy, SW" - But on the photo/schematic, it says Lx and Ly? What should i do, if Lx and Ly isnt a option on my joystick?
Could I instead just use 1 joystick instead of 2? will it still work sir?
L mean left.
Will work. Use VRx, VRy of Same Joystick.
@@aslamhossain1 so both 2 joystick’s, I’m gonna use VRx and VRy? I’m beginner-level sir, sorry
2:36 when you are configuring your master HC-05. Is it the same file "Configure_HC05_Master_Slave" you open up? Ore is it another file
Same file for both hc-05
Sorry sir, I'm still a beginner in this field, can I apply this program to the ESP8266 module?
No. Its for arduino. You can make it by esp32: ruclips.net/video/TEyqKFT7BCA/видео.htmlsi=b8dI63K60XEuRg_H
your tutorials are very helpful...
Thank you
What joystick are these trying to find the parts just get a lot of controller spares
www.google.com/search?client=ms-android-xiaomi-rvo2&sca_esv=847412b30e358a21&sca_upv=1&sxsrf=ADLYWIKuNA64cqJlr0OiikN2CJk9XXJEqA:1723152699480&q=analog+joystick+arduino&udm=2&fbs=AEQNm0Aa4sjWe7Rqy32pFwRj0UkWd8nbOJfsBGGB5IQQO6L3JyJJclJuzBPl12qJyPx7ESIJKsuo8DSJKOxlDDbn2sXiP2DA1JodL-8OvpqfPcsNcQUuuwc5TAoUZ87rVxy1Xv44fXe4anLnvLcDFC-g4Q79g5ePUy5vwOhyyW06dpaKgZBnQRs&sa=X&ved=2ahUKEwiii6-ErOaHAxXYSmwGHXVuO4EQtKgLegQIGRAB&biw=393&bih=733&dpr=2.75#vhid=NpUU8g3pjMyiQM&vssid=mosaic
When I try to configure the HC-05 and try to input the AT commands to assign slave/master, I am being met with "ERROR (0)" in the serial monitor terminal. Do you know how to fix this issue?
Please try again...
@@aslamhossain1 It was just different commands I guess cause I got it to work
@@makanh.6726 How? it says error(0) for me no matter what
at the start when paring the 2 module you olug it on the bread board what about the other board that was already on the breadboard what is it?
You need two HC-05, one for tx another for rx. i've used two different HC-05 module.
What is the maximum distance the car can move away from the remote controller so as not to lose the connection? For me it is 2 or even meters. Also I lose connection when I direct the remote to the other side of the car.
According to datasheet it's 10-20 meters. May vary in practical
i am trying to apply this project, in the first step of putting the HC-05 in A T mode, it is turning only red light instead of red and blue light, what should i do in this case? Note: i am using Arduino Pro micro
Press and hold enable button then connect power. Then after a few second AT mode should be activated.
@@aslamhossain1 i already did this step but it is blinking with red only, also when i trying to send the A T command lines to the serial monitor, but nothing appear in the serial monitor
@@ربابآلسهوان I am also getting this issue but when I type the commands into the serial monitor, I am getting some symbols which usually show up if the serial number I am using is incorrect but I am using 9600. Not sure what the issue is with it.
The HC05 master doesn’t seem to be retaining the role change to 1 but says ok to all steps but the two HC05 don’t seem to connect to each other after completing all the steps
I have tried both modules as master and slave but have the same problem on both not sure what is causing the issue
Can i control the car using any mobile app? If i don't want to use joystick?
Yes you can. Need to change whole code.
im getting an error that states "avrdude: stk500_recv()" and I cant figure out what the problem is have you had any experience with this issue?
Port problem. Please select the proper board, processor and port number while uploading the code.
@@aslamhossain1 Is it possible to use an arduino nano with this?
@@makanh.6726 yes. I also used arduino nano
@@aslamhossain1 Did you have any issues with the L298N? When I test it with one side it works fairly fast, when I do it with both sides sometimes I have to give it a little manual turn to start it up and its very slow but a lot of the time it is just not turning. I am not sure whether or not it is a power issue or what. The wiring seems to be perfectly fine.
@@makanh.6726 maybe the pwm value in the enable pins is lower.
I just tried everything but my motors are moving uncontrolled all the time and they are changing directions for just a sec also. Do you have a solution for this?
Power supply problem in transmitter.
Need 5v constant.
Use 2s battery. 8v in Tx Arduino Vin
good job
Thank You
If I use Arduino Nano as master and Arduino Uno as slave, will it still work?
It will work.
i have a problem, when my car just started, it runs normally but after that i can't controller, i press reset button on arduino board and it back to normal
how can i fix that
Power supply problem in transmitter
Use 5v at arduino and joystick
i dont understand, it is only master-BT-module that cant not do AT+RMAAD. but Slave-BT-module does it fine
Make sure the BT Model is HC-05. Because only HC-05 can act as Master.
@@aslamhossain1 both are HC-05
when i type om master "AT+RMAAD" ok is not showing... im going to exam soon sir, can you help me
Can i skip the AT+RMAAD -step?
Its for removing previously paired device. If any then you need to remove. Otherwise it will work without this command.
ভাইয়া nrf240L1 নিয়ে এমন ভাবে একটা রিমোট কন্ট্রোল গাড়ির টিউটোরিয়াল চাই প্লিজ।
InShaAllah
@@aslamhossain1 আচ্ছা এই টিউটোরিয়ালে আপনি রিমোটের বেলায় জয়স্টিক দুটার ক্ষেত্রেই x, y দুটাই ব্যবহার করলেন যে? আমার জানামতে এখানে একটা জয়স্টিক শুধুমাত্র x অক্ষে এবং অন্যটা শুধুমাত্র y অক্ষে কাজ করে। তাইলে একটারই দুইটা x,y নিলেন যে?
Bro can I upload another code for my BLE control car. Only change pinout
Yes
Unable to open diagram and code link please help
Try from computer or Send a mail on aslamhshakil20@gmail.com
5:12 how do you connect the battery with the master?
8v with Arduino Vin and ground.
@@aslamhossain1thanks.
Plz mention the code in the comment
Open the link given in the description. I've Uploaded in my github account.
Our car not work
👏🏻
🤝