Видео

ledcSetup(error)

ledcSetup error

which library are u using, where did you get it ?

Vai tutorial video dien

We are doing the same project can u help us

Sir,,Could you share code?

Good

Damn! Its great video keep it up!!!

you can get required 5v output from that motor driver too , no need of extra buck converter

Full video please

Bro...plz share the code and diagram

great sir g .... sir i need all components of this robot can you share your whatsapp number

So if it was a bad laptop battery why does it test so well and work as a power bank?

Considering that portable devices like phones, tablets and laptops are only allowed to have a max 9,999mAh battery for air safety reasons, a single cell isn't going to have much use as a power bank. And most devices do not have that much capacity. Even when using all the cells you will still get a max of ~9,999mAh. And you can buy 10,000mAh banks with fast charging and other modern features for $20. Also consider that if the cells are from an old laptop, then they're gonna be worn out and not have full capacity anymore. I applaud your attempt at trying to find uses for old electronics, but this is just really not worth the time or effort. By the time you get a BMS board shipped to you, find or buy materials for a case and spend the time stuffing around putting it all together, its just not worth it. Not to mention the danger of people wiring it up wrong and causing it to explode or start a fire. Those cells are probably not designed to be stacked like that for heat reasons. While in use, they will likely get hot and expand. Especially while charging. The battery cells are way more useful just being left in the old laptop and using the laptop as a server or donating it to charity. That way the whole device will still be useful and it will have some battery backup for when the power goes out. You're also creating less e-waste.

What kind of batteries did you use, and how many? Greetings from Colombia 👋

This is GoBLE! Good job!

আমি কি 12v এর পরিবর্তে 9v এর bettery ব্যবহার করতে পারবো?

ভাই মোট কত টাকা লাগসে এটা ফুল বানাইতে

Nice

Wow

I did the task..bt not unlocking the circuit diagram and code

where did you get the links? in the video you paste them but never copy them

Sir i need a code for 5 channel array sensor

Can this robot follow paths that split into two or basically when there are like diamond shapes in the path?

what kind of paper

This circuit will not blink forever.

How i can add more li8s.

Its working very good concept.

Can i use metal toy train. Approxmently 3 kg weight pulling

Can it go faster with the same motor

No information about transistor ???

Can i use esp 32

❤❤❤#solderingart ❤❤❤

Bro bro how many volt can i give in transmitter and receiver..pls tell me

What software do you use to show the schematic for the circuits? I am trying to make a report and having issues trying to find a schematic that works good.

Waste time

how can i purchase 6 ir array ?

Does this work with 4G?

CRAP! It does not work if we do the circuit the way it is explained here

Hi! Do I need to install any drivers before installation? (by type ift232-s16)

i dont understand, it is only master-BT-module that cant not do AT+RMAAD. but Slave-BT-module does it fine

when i type om master "AT+RMAAD" ok is not showing... im going to exam soon sir, can you help me

what is BluetoothSerial?

ledcSetup(R, 5000, 8); // Channel 0 for Motor A, 5 kHz frequency, 8-bit resolution ledcAttachPin(enA, R); ledcSetup(L, 5000, 8); // Channel 0 for Motor A, 5 kHz frequency, 8-bit resolution ledcAttachPin(enB, L); Why error in this line??

i have a problem, when my car just started, it runs normally but after that i can't controller, i press reset button on arduino board and it back to normal how can i fix that

how much volt and ampere battery are you using to power esp32

Please can you make a video using this transmitter and l298n motor driver to make a rc car pleaese? Im begging you. I need this RIGHT NOW.

Compilation error: 'ledcSetup' was not declared in this scope This error is coming

ledcSetup' was not declared in this scope i habe this erreur

Hi sir, if I make a sensor with 3 IR sensor instead of ur 6 array linr sensor will it's work.For That the same code will rum?