Spent the entire day checking hoses, filters, connections, etc with no luck. Error code read LF. Came across your video and had the exact same problem. (Punctured/worn out pressure sensor hose.) Thanks for posting. Helped a ton.
I checked the Pressure switch hose and" BINGO" small pin hole from the outer tube rubbing on the hose, replaced the hose all is go, Thanks to your RUclips Video!!
Thank you that helps tremendously that's what mine is doing and cleaned out all the calcium buildup and that didn't work next is to check that and the pressure sensor switch thank u for showing this makes it easier to know what I'm looking for
Adam, thank you. Your step by step troubleshooting showed me the filter in the bottom which was severely plugged, and it solved the problem with my WFW9050xw00.
Holy shit an actual video of the model I had 😂 It’s almost like they only made it that one year and then deleted its history off the face of the earth, mine quit working I didn’t even look at it and went and bought another now seeing if it’s fixable to sell
If you take the bottom plate off there should be a manual taped to the inside the back of that panel, I did the code error reader deal and mine showed F6E1, you prolly didn’t do yours did you?
I cleaned out the same drain but it did not help, I will check now that hose , so does it just hold air or water and where can I purchase a hose like you described?
Omg, I just changed the motor pump and solved my first initial problem however immediately as I ran my first cycle it stopped at midway and gave code f6 e1 which I'm hoping this will be the issue. I just don't feel like it is the control board cuz it would have already given me that code to begin with.
I thought I found some pin holes, but covering them it did not fix it. Whats funny is that if I put it on rinse / spin cycle, the water fills as it should. But any wash cycle it continues to do the 6 minute cycle with the error code flashing. Looks like I will be calling Whirlpool for some help.
Anthony London I am having the same issue. Did everything in this video. The only thing I have yet to replace is the water inlet valve. Hopefully that will fix it.
My washer (WFW9151YW00) would also stop 6-10 minutes Into cycle. It did this in cold and warm water. No issues with hot or rinse cycle. It flashed the LF (low fill) code. Water would fill in but not as much as it usually does. My fix was replacing the cold water valve (water inlet valve).
Spent the entire day checking hoses, filters, connections, etc with no luck. Error code read LF. Came across your video and had the exact same problem. (Punctured/worn out pressure sensor hose.) Thanks for posting. Helped a ton.
I checked the Pressure switch hose and" BINGO" small pin hole from the outer tube rubbing on the hose, replaced the hose all is go, Thanks to your RUclips Video!!
I was fixin to blow my washing machine up until I found this video!! Thank you
Thank you that helps tremendously that's what mine is doing and cleaned out all the calcium buildup and that didn't work next is to check that and the pressure sensor switch thank u for showing this makes it easier to know what I'm looking for
been at this issue for week and completely overlooked the tear when inspecting the hose initially, thanks for the wise words
Hey Adam, I did everything you did troubleshooting and was out of ideas until I saw your video. Changed out the hose and problem solved. Thanks a ton.
Adam, thank you. Your step by step troubleshooting showed me the filter in the bottom which was severely plugged, and it solved the problem with my WFW9050xw00.
Holy shit an actual video of the model I had 😂 It’s almost like they only made it that one year and then deleted its history off the face of the earth, mine quit working I didn’t even look at it and went and bought another now seeing if it’s fixable to sell
Thank you. The hole in the hose was exactly my issue
here goes nothing. wish me luck. thanks for the info adam!
Thanksfor the video, My vac line was torn up right on the valve cut it and replaced it, worked great.
Thanks for covering all the items. I'm going to go tackle this now.
Thanks for the video! Exact same problem over here. Your video was very helpful. 👍
The filter had coins, drywall screw, pen sleeve, hair pins, clips etc. waiting for the wife to try after I cleaned it. Thanks!
GREAT JOB SAME THING HERE! THANK YOU!👍
Great job. Now I have a few diagnoses. Unfortunately, I do not have time to fix it.
Thanks so much, worked like a charm
Thank you.
If you take the bottom plate off there should be a manual taped to the inside the back of that panel, I did the code error reader deal and mine showed F6E1, you prolly didn’t do yours did you?
hey,
how did you take out the front panel?
I cleaned out the same drain but it did not help, I will check now that hose , so does it just hold air or water and where can I purchase a hose like you described?
Is this the part WPW10004260 Washer Water-Level Pressure Switch Hose ?
Is this correct PN I have same issue
that looks right. you can also fix by using electrical tape over the hole
Omg, I just changed the motor pump and solved my first initial problem however immediately as I ran my first cycle it stopped at midway and gave code f6 e1 which I'm hoping this will be the issue. I just don't feel like it is the control board cuz it would have already given me that code to begin with.
check the pressure hose for holes
I cleaned out the filter at the bottom but now it wont turn on at all. It just beeps once when press the power button and then nothing.
I fixed this by simply turning the knob to "normal"
What the name of the part?
You still didn’t fix issues?
I thought I found some pin holes, but covering them it did not fix it. Whats funny is that if I put it on rinse / spin cycle, the water fills as it should. But any wash cycle it continues to do the 6 minute cycle with the error code flashing. Looks like I will be calling Whirlpool for some help.
I got the same problem any luck with finding a fix. Thanks
Anthony London I am having the same issue. Did everything in this video. The only thing I have yet to replace is the water inlet valve. Hopefully that will fix it.
Scott Hazlitt: I’m in the same boat. Can you let us know if you have any success with the inlet valve?
@@cyberS_2024 Did this fix the issue Scott? I am having the same problem
My washer (WFW9151YW00) would also stop 6-10 minutes Into cycle. It did this in cold and warm water. No issues with hot or rinse cycle. It flashed the LF (low fill) code. Water would fill in but not as much as it usually does.
My fix was replacing the cold water valve (water inlet valve).