Will definitely give this a try. I'm looking for something that's reasonably tough, but the big requirement, which seems hard to find, is that it doesn't wear off with a bit of friction. I'm not printing ball bearings or anything, but the parts need to be able to rub against each other a bit without powder coming off.
We will definitely recommend the Anti-impact resin for you ! This resin is suitable for your application needs，you can check our web resione.com and search Anti-impact！
Yes，it compatible with M5S ，we have the settings on our official website you can download .You can boil the water ，and then you put the bottle resin into the hot water to heat it 5-10minutes，and you good to go ，make sure the cap was tight！
Здравствуйте!!! Приобрёл вашу смолу! Она мне очень нравится. Но есть одно но! Точность печати отверстий очень низкая, размер уходит до 0.3мм. Причем печатал и на anycubic photon mono 2 и на anycubic photon mono m5. При разных настройках. Пробовал даже 2.5 секунды засвета делать. И все равно точности нету. Смолу перед печатью нагреваю до 33гр.
TH72 is a low water absorption resin and can be used in humid environments, M70 is low shrinkage and should have a lower water absorption than normal resins, so you don't have to worry too much about this if you mix the two. and for the hygroscopic，it dissolves and cracks ，but it doesn't melt.
Can you tell me what you intend to use the prints for? Can you elaborate on what you want to use for the application. It may be possible to meet this requirement
Need this in black 👌
Will definitely give this a try. I'm looking for something that's reasonably tough, but the big requirement, which seems hard to find, is that it doesn't wear off with a bit of friction. I'm not printing ball bearings or anything, but the parts need to be able to rub against each other a bit without powder coming off.
We will definitely recommend the Anti-impact resin for you ! This resin is suitable for your application needs，you can check our web resione.com and search Anti-impact！
I wish you would send me a sample to review. I make action figure parts and i need something that will not snap on an shoulder joints.
what is measure hole tool? can you share please?
search: Taper Bore Gauge
Hello, can you explain how to heat the resin before printing? And whether it is compatible with M5S printer or not?
Yes，it compatible with M5S ，we have the settings on our official website you can download .You can boil the water ，and then you put the bottle resin into the hot water to heat it 5-10minutes，and you good to go ，make sure the cap was tight！
Can I mix the the typical Photopolymer Resin with your Anti-impact Resin Durable Nylon-like ??
Not really recommended, because we have specific support setting and parameter match to it ， but you can try it
how about warpage in thin flat parts (.060") like a car hood?
i think that works too ，
The resin itself is very suitable for some end-use products, some parts of the car model are suitable.
Здравствуйте!!! Приобрёл вашу смолу! Она мне очень нравится.
Но есть одно но! Точность печати отверстий очень низкая, размер уходит до 0.3мм.
Причем печатал и на anycubic photon mono 2 и на anycubic photon mono m5. При разных настройках. Пробовал даже 2.5 секунды засвета делать. И все равно точности нету.
Смолу перед печатью нагреваю до 33гр.
Hello there ，for technical problem you can contact this email ： support@godsaid3d.com ，our technical will provide information professionally
Is it possible to mix pigments in this resin?
Yes it can
Will this dissolve in DMSO? Is it hygroscopic?
TH72 is a low water absorption resin and can be used in humid environments, M70 is low shrinkage and should have a lower water absorption than normal resins, so you don't have to worry too much about this if you mix the two. and for the hygroscopic，it dissolves and cracks ，but it doesn't melt.
Hello what about heat?
this resin is not heat resistant resin，like only about 40 degrees
Can you tell me what you intend to use the prints for? Can you elaborate on what you want to use for the application. It may be possible to meet this requirement
@@godsaid4502i want to 3d print durable gears
@@godsaid4502Hello you didn't reply
I think the Anti-impact resin will be the better option for this application
@@elsunshine9976