My 2003 X5 has the 3 litre M54 engine, and this completely explains what is going on with my rough idle.....new plugs, new coils, new MAF, new gaskets...etc. No vacuum leaks. After a good quick drive on the freeway, engine is good and warmed up, runs like a new vehicle...goes into closed loop at idle, runs like garbage with misfire codes and fuel trim codes. Im gonna change out bank two O2 sensor immediately! Thanks for the great video...it helps people understand how o2 sensors work, and the purpose of closed loop on a modern fuel injection system. BRAVO
Thank you for the video I just found out that owner before put Diesel lambda sensors into the 335i N54..... thats crazy... and this crap from exhaust proved that my car is running rich
Worth adding that on a cold engine [O2 sensor not heated up] and during hard acceleration[O2 sensor too slow for what you try to do], it's the mass airflow sensor that takes over, so that lambda values can be estimated/guesstimated from the lookup data.
Exactly what I'm experiencing. Lean mixture bank 2. Now having misfire bank 2. Have done a smoke test. No leaks. I will change my O2 sensor. But let me look at the readings first. Thanks a lot. This is life saving.
Thank you so much for your tutorial video. It's really excellent. I bought a 2013 BMW 328i xDrive N20 4 Cyl in Dec 2019. It had drivetrain malfunction and misfire on Cyl 2. The dealer suggested to replace 4 coils & spark plugs. I replaced the 4 coils and 4 spark plugs, and the battery (was low). The drivetrain mal function error went away, but the misfire error persisted. I replaced the fuel injector (looked black) on Cyl 2 to no avail. Yesterday, I cleaned the MAF (look new and clean to begin) to no avail. Your video suggested my car may have O2 sensor issue. I will give it a run and checked the 4 spark plugs as you did to confirm the black sud on #2; I may have more than 1 Cyl misfire. I think my car may not have bank 1 and 2 as your N54. Much thanks to any suggestions you may have. Thanks again. This video is really excellent.
I just fixed my misfires and limp mode because of this video. thank you for this awesome informative video. When first startup, running real rich, clear codes and ran fine until i got into the power band at WOT. then got o2 sensor errors, and misfires. Love your videos. (2008 335i, 112,000 miles. FBO except still running stock intercooler, MHD BEF, JB4 piggy back tune map 2 mostly)
I have replaced all of my o2 sensors on my N54. The pre-cats I did at 120k proactively. The post cats, I got a specific code. The post cats really don’t do much other than monitor the pre-cats and make sure they are running correctly. You can also monitor them live on a scanner. The scanner should have specific values. If values aren’t what they should be, then you know what specific O2 sensor is bad. Easiest thing to do is take the cats out of the car if you are looking to change them out. They are a PITA otherwise.
Full blown misfire mode sets a code and turns off the injector for that cylinder until the next restart. It will try on restart to run the misfiring cylinder again but will again turn off the fuel injector if the cylinder is still misfiring. It was running rough but it was not in full blown misfire mode...
As always keep up the great and informative videos making owning my N54 a lot less stressful and daunting and encouraging me more and more to work on it myself!
Damn, i thought it would be an expensive 2021 but you just saved me hella money since BMW said it was my Injectors! Thanks a lot for the video and for sharing your knowledge.
Going through the same on a 2011 N52 right now. Original sensors with 200k kms (~130k miles), no codes set, unplugging the sensors brings back midrange torque and improved drive ability and fuel mileage. I thought it was a DISA valve issue, glad I checked O2 sensors first! I just assumed they were ok because no codes were set. OEMs recommend replacing O2 sensors by 100k miles, now I know why.
You.....ROCK!!!!! LOL. I can't tell you how much you've helped me with this video. Thank you so much. It seems like no one talks about the importance and or effects the O2 sensors have on our cars. I have an E46 M3 and I just changed out my OEM Catted Headers for a set of catless ones and I have had a real problem with the car having codes on the O2 sensors as well as many other codes just coming up even after I've done a tune that is supposed to adjust the sensors for that particular set up. Miss fire codes and strange stuff. Exactly what you have described and shown here. You were so thorough and I am so glad. I am having the miss fire codes just like you had on bank 2 but only on bank 1 cylinders. (Cylinders 1&2) indicating it is likely the O2 sensor on that bank (as you similarly showed) that is the culprit. It has shown a couple of times where both pre cat sensors are throwing codes. But usually it's only showing a code for the pre cat sensor on only bank 1. I have been thinking that it could be so many things that I just wasn't sure enough yet to pop for any one or two parts to try and solve it. I thought maybe vacuum or ground problems. But I'm sure enough now to start with this. Thank you again!
DANG!!! This was EXACTLY what I needed. Wow. Thank you SO much for this fantastic descriptive video. Now I know exactly what my problem is. I'm very excited to fix it now! Thank you !!!
3 года назад+1
I have a Mercedes W203 that was smoking a lot. I had no idea what to do. Thanks man. You saved my life (and my pocket).
I thought maybe it was leaky injectors but decided to do a bit more research before buying parts. glad I found this video. mine is running soo rich. crazy fuel smell and white smoke. thought it was leaky index 12s will be changing these sensors, installing new coils and cleaning my plugs as the have less than 100 miles. changed them chasing a misfire issue. only 95k on motor and 106k on chassis
Thanks for the detailed info on how to change the spark plugs. The steering rack removal was the key to this DIY. I bought the exact socket from FCP euro and it made the spark plugs much easier to deal with.
You mention using your affiliate link for purchases- and I’d LIKE to as you’ve been a great help to me and others, but I don’t see one for the “INPA K+D Can” cable. Please send or reply with the link because I’m about to start loading a dedicated laptop and will want to have the cable by the time the software is ready. Thanks for everything
Really happy I stumbled across this, I grabbed up a used BMW and it has the rough idle, as soon as I figured out it was about 30 seconds to a minute I instantly though heater, but since I am not familiar with BMW I figured it couldnt be that simple right? Well I will run this test in the am, and am doing a full drain and replacing everything anyways, just add the o2 sensor to the list
Fyi to save some money the o2 sensors are the same along as you get 2 rear ones (2 extra long ones will work but wont work viseversa... meaning two short ones obviously wont work and would cost way more for the short one vs long one meaning bank 1 vs 2 )
uuu god i love you man... like the best teacher ever, i have exactly the same problem, but not the same tools :( ... but now i know what to do thanks to you... greetings from Chile!!!!
I started my car cold and engine started shaking right away. I hooked up a code reader and saw cyl 4,5,6 misfire. I let the car running for a bit more and then started seeing the o2 sensor code. So is it my o2 sensor or something else? When I clear code, I do feel that the engine smooths out for a few seconds.
I swear i love people like you who , i have i think the same problem at 325i 2008 n53 now bc i saw this video and i remember when i changed my sparkplugs and coils and i saw some of them was so dirty and some of them „clean“ like yours , i want to repair by myself what i can because here in Swiss if you go to a service they take to much for nothing and i hate it, but that s the reason exist people like you and youtube to try if we have enough time and we want this to try, big love man P.s from where can i order a usb odb2 cable? Im not the best in cars or repairs but i want to handle what i have , thank you
Hi! I actually have the same problem on Bank 2 but I get low voltage values so the engine thinks it runs rich in bank 2. But it gets a little better when the engine has warmed up but still noticeable lower voltages than bank 1. I haven't checked the spark plugs yet but i will. I have the N53.
Great video. I like the logical trouble shooting. I’m having issues with my fan on a 93 300e which may have the same 3.2 engine???? My car was almost overheating at 120 while driving thru the McD take out line. The fan I think was off. I would think it should have been on at that temp. The fan was on yesterday. Are there two different signals to the fan??? One based on water temp and the other based on something else? Shouldn’t the fan be on at 120? I am suspicious of my wiring harness on the 93. It is the old brittle one. The wires near the temp sensor look a bit delaminated. Trying to figure out what to do. Don’t want to ruin engine. Probably gotta get that new harness in and hope that fixes it.
My voltages are all fine but I keep getting 2CAA Oxygen sensor heater function & 2CA6 Oxygen sensor temperature. All 4 are new sensors . Any ideas? I've tried harness, DME, adaptations, untwisting wires, fuses. Nothing!
You may have saved me money I was about to order a new set of Delphi coils and 1 step colder spark plugz from fcp my car is running like yours at 2:47 😰 So ima get to ordering the O2 sensors and how to change one on my own
😃 great explanation of the pre-cat I have a BMW E65 doing the same thing, tested with ista/d same result, is it possible a O2 can go bad in 3 years? Can something burn out the heating mechanism? Like a recent replacement trans? or a replaced generator?
Well I'm back about 10 months later and I have bought an E90 2008 335XI. (I still have the E46 M3 too). But I fear greatly that the O2 sensors need to be replaced on it as the car is having horrible cold starts with misfires on first 1 and 3 then if it is a bad cold start it's even more cylinders. One code read showed oxygen sensor code. The coils
Just learning here, bare with me... Cylinder 6 plugs appeared wet when you removed it. Is that gas? Also, will faulty O2 sensors cause gas to collect in the cylinder? Just trying to determine if I have a bad injector in Cylinder 5 (which I get a consistent misfire) or if my O2 sensor in bank two is bad. I have JB4 installed and three days ago I performed JB4 MHD BEF and car hasn't ran right since, primarily at idle/cold starts. I get a rich gas smell when idling.
1 NOV 2020 11:29am Central California S.O.S Bought a 2012 335i e92 n55 from this kid. He had it raced out with a vrsf catless downpipe, vrsf charge pipe & tuned with a MHD stage 1 tune. Fast forward, I gotta get it smogged. Took off the race kit, deleted tune, and put the stock parts back on. For maintenance purposes I installed new O2 sensors (i believe its 2 for this car), new spark plugs and ignition coils. Started her up, ran her for a good 5 days and I'm getting thus code. Don't know what too do, help lol. P0133: oxygen sensor circuit slow response bank 1 sensor 1. Permanent.
So my bank 2 is doing the same...but the rear one is also is at like .6-.8 but the front one goes to 3.8-4.1 volts! So are they both bad or the cat or why are these cars such a nightmare 🤣
Your video is so explanatory. Need help what inpa cable to use on 2009 335i n54. E92. there so many and some of them don’t work according to users just.
@@VehicularDIY I currently have all new o2 sensors and am going to put in soon and I was curious to know if I have to reset any adaptations or will the ecu just automatically dial in everything after replacing all o2 sensors
when you disconnect the sensor on a 318D, will it have the same effect? cause it also run bad only in idle and i don't get a engine light. greeting from Belgium! great video!
Thank you for a very informative video. Please could you tell us what is the app you running on your phone and on your laptop. Are they free to download or subscription based? Many Thanks.
Good video bro It helps alot i have a audi s4 and couldnt figure out why it was misfiring i changed alot of stuff still the same. Next its the 02 sensors. Has all this syptoms Thank you! 👍
it seems fine until I give gas , that's normal right ? I can't pass emission test and I don't know why ... I assumed the o2 sensors but it seems right to me
I’m giving this a long shot in hope that you can reply. I’ve been having trouble with diagnosing my car since I bought an eBay inpa software but it is in German. Have very little computer skills and was wondering where you got your software from? I currently have a hp with windows 10
Hey thank you for this video, I'm currently changing out my turbos due to blowing a seal on one of them and my mechanic recommended replacing both pre-cat o2 sensors in a pair. They're quite pricey and I was having hesitation issues but attributed it to my wastegates also not sealing properly. To my knowledge the post-cats are ignored now that i'm catless but i will definitely check the voltage on my o2s prior to purchasing them. Also, im not sure if you know or not, but would xdrive vs non xdrive be a problem in regards to reaching the o2s from under the car? I know it's a tight space but worry that the subframe is in the way. Hopefully not!
I recently bought a 2013 BMW 335is 34k miles from Oregon (salted roads) I got codes for O2 sensors. One said too lean and the other said too rich. Are they really bad or could be something else? I have open recall for injectors getting it done in 2 weeks at dealer. Thanks!
Hi ! I have exactly the same problem I think on my x6M (s63) No CEL, no hesitation on throttle, no error message , very slight instable idle, high fuel consumption, pop and bang on cold start, pop and bang on shifting with sequential mode, only black smoke (tail Pipes become black), car has +100k miles on the clock. Do you think my oxygen sensor are faulty too ?
Nice work identifying the af sensor issue. Your long term/multiplication fuel trims are both very negative after the sensor replacement. Did you manage to find the cause and fix for that?
I have a 29E1 code that pops back up every day or so. I just keep clearing it to try to narrow down the issue. I have a rough start in the morning after it’s been sitting all night but otherwise my starts are pretty smooth. Once it warms up, it smooths out too. I thought maybe o2 sensor but if it doesn’t give me issues warm, should I look more at injectors instead? I have also gotten a cyl 5 misfire every now and then, so I’m leaning towards injector in bank 2.
Will it cause the limp mode in my 07 E70? I am having random limp mode regardless driving style/load/speed. I have replaced camshaft sensor, vanos solenoid, eccentric shaft sensor and disa valves. The code I pulled up is 2c31.Thanks
Are you using an OBD enet cable to code or to view parameters on your F15 like you are doing with your E90? I'm very interested because as well as you we own an E90 and a F15. Thanks in advance buddy!
Hi, could you please help, I'm a bit confused. On my BMW N53 pre-cat sensor has a long cable and they are on the left side of the engien, after cat sensor has short cable and its under the car. If I have the same reading like you wich one should I change?
I'm currently having a really bad misfire, getting 2c7c lambda behind and 2c2e in front of catalytic and cylinder 6 misfire. Would that mean both sensors on bank 2 gave out? I also have jb4 tune and can't get rid of code
I have same issue with a 2009 n52, 328xi. I've changed plugs and bank 2 coils. I'm trying to figure out if its the o2 sensors that are causing the misfire codes (only on bank 2) - and for some reason it says catalyst efficiency is below threshold?? on both cats. the numbers look ok for o2 sensors i guess, except on the bank 2 mix, it's adding a lot more fuel than its supposed to in the long run. little help?
I did just today change my downpipes to the original ones just to pass the TC. And got those error, is it possible that this happend cause i put the oem downpipes back in( stage 3 and upgrade turbos)?
Have you ever had an issue when you start your car up and immediately your car starts to rev up and down repeatedly and when you step on the throttle it’s not responsive? When you put it on drive car still won’t accelerate but starts to jerk really rough?
2c7e oxygen sensor emissions control.upon starting rough idle, within 10 seconds it straightens out, but Engine running rich, you can smell the petrol. 2 oxygens sensors in the engine bay have been replaced, i take it thats pre cat, so now i need to replace 2 by the cats?
i’ve been running them backwards and running rich for about a month ugh i need to switch them! i forgot to mark them when upgrading to catless downpipes
I'm having an odd issue with my n52, the bank 2 sensor is reading 0.29 volts while bank 1 is normal. I have replaced the sensor, but the problem is still the same. Help!
I’m having a similar issue I put all brand new Coils and spark plugs but my cylinders 1-3 are still misfiring and my spark plugs are wet with gas when I take em out so you think my O2 sensor Is the problem .?
hey i did exactly what you did in the video. But im still having the same issue, ive looked everywhere online for a solution but im getting a lot of mixed answers. i was wondering if you could help.
I Have a question so I put in a new mass air flow sensor and the car started to run rough and won’t idle once i unplug the MAF it worked like normal well it idles as best it can. I do have a code for O2 lambda sensor and maf. I can see values With my scanner when the maf is plugged in. So do I need to replace all the o2 sensors now that my maf works?
If could reply back. I would appreciate. It. I recently purchased a 2001 Honda Accord lx. I bought it from a family member and they put another motor(used) basically. When I start the car it’s fine. If I drive the car it only gets up to 45mph and it doesn’t have anymore power. It runs raggedy from the cold start but once I start it. But after the engine warms up it runs smooth. The code is air fuel ratio sensor. The guy that put the engine in says it’s the ecm computer could you help me out
Can u paste here the part number for bank 2 pre cat lambda that u have replaced? I am about to buy one and I really dont want to get a different one :) I would really appreciate that
I have an 04 545i that gave a check engine that says increase emissions any idea what it can be ? It does smoke like urs did guessing its running too lean or too rich
This is Crazy I changed my O2 Sensor Bank 1 upstream. I'm still getting a low circuit reading PO131.. it may be poor fuel ratio. I also changed the EVAP Valve. Still Showing code plus I smell a lot of gas. I also have a little mis idle
I'm have what I think may be the same symptoms on my X5 xdrive50i. My code is 2D0D. Would you happen to know if this is the same? The code comes up on carly as air mass 2 Plausibilities or air volume 2 Plausibility.
Great video! I have a bmw 550i and it’s throwing a code P0175 running rich. Scanner shows bank 2 short term trim -3.12, long term -23.44 Bank 1 short term trim -1.56,long term -6.25 Is it the o2 sensors causing it to run rich? Or can it be something else? FYI it’s a 2011, 80k miles, I do burn a little oil.
My 2003 X5 has the 3 litre M54 engine, and this completely explains what is going on with my rough idle.....new plugs, new coils, new MAF, new gaskets...etc. No vacuum leaks. After a good quick drive on the freeway, engine is good and warmed up, runs like a new vehicle...goes into closed loop at idle, runs like garbage with misfire codes and fuel trim codes. Im gonna change out bank two O2 sensor immediately! Thanks for the great video...it helps people understand how o2 sensors work, and the purpose of closed loop on a modern fuel injection system. BRAVO
Thank you for the video I just found out that owner before put Diesel lambda sensors into the 335i N54..... thats crazy... and this crap from exhaust proved that my car is running rich
Worth adding that on a cold engine [O2 sensor not heated up] and during hard acceleration[O2 sensor too slow for what you try to do], it's the mass airflow sensor that takes over, so that lambda values can be estimated/guesstimated from the lookup data.
There are no crap MAFs on an N54, just MAP
You always seem to post videos at the appropriate time when I'm having the exact same issues with mine brother 😁
truth
I second that.
Exactly what I'm experiencing. Lean mixture bank 2. Now having misfire bank 2. Have done a smoke test. No leaks. I will change my O2 sensor. But let me look at the readings first. Thanks a lot. This is life saving.
Thank you so much for your tutorial video. It's really excellent. I bought a 2013 BMW 328i xDrive N20 4 Cyl in Dec 2019. It had drivetrain malfunction and misfire on Cyl 2. The dealer suggested to replace 4 coils & spark plugs. I replaced the 4 coils and 4 spark plugs, and the battery (was low). The drivetrain mal function error went away, but the misfire error persisted. I replaced the fuel injector (looked black) on Cyl 2 to no avail. Yesterday, I cleaned the MAF (look new and clean to begin) to no avail. Your video suggested my car may have O2 sensor issue. I will give it a run and checked the 4 spark plugs as you did to confirm the black sud on #2; I may have more than 1 Cyl misfire. I think my car may not have bank 1 and 2 as your N54. Much thanks to any suggestions you may have. Thanks again. This video is really excellent.
I just fixed my misfires and limp mode because of this video. thank you for this awesome informative video. When first startup, running real rich, clear codes and ran fine until i got into the power band at WOT. then got o2 sensor errors, and misfires. Love your videos. (2008 335i, 112,000 miles. FBO except still running stock intercooler, MHD BEF, JB4 piggy back tune map 2 mostly)
I have replaced all of my o2 sensors on my N54. The pre-cats I did at 120k proactively. The post cats, I got a specific code. The post cats really don’t do much other than monitor the pre-cats and make sure they are running correctly.
You can also monitor them live on a scanner. The scanner should have specific values. If values aren’t what they should be, then you know what specific O2 sensor is bad.
Easiest thing to do is take the cats out of the car if you are looking to change them out. They are a PITA otherwise.
Hands down the best DIY n54 videos on RUclips! Extremely detailed and well explained. Thank you so much for the education!!
Full blown misfire mode sets a code and turns off the injector for that cylinder until the next restart. It will try on restart to run the misfiring cylinder again but will again turn off the fuel injector if the cylinder is still misfiring. It was running rough but it was not in full blown misfire mode...
As always keep up the great and informative videos making owning my N54 a lot less stressful and daunting and encouraging me more and more to work on it myself!
Damn, i thought it would be an expensive 2021 but you just saved me hella money since BMW said it was my Injectors! Thanks a lot for the video and for sharing your knowledge.
Same here bro im like huh hold on wait a second 🤔🤔🤔🤔 bmw out here robbing us
Going through the same on a 2011 N52 right now. Original sensors with 200k kms (~130k miles), no codes set, unplugging the sensors brings back midrange torque and improved drive ability and fuel mileage.
I thought it was a DISA valve issue, glad I checked O2 sensors first! I just assumed they were ok because no codes were set. OEMs recommend replacing O2 sensors by 100k miles, now I know why.
You.....ROCK!!!!! LOL. I can't tell you how much you've helped me with this video. Thank you so much. It seems like no one talks about the importance and or effects the O2 sensors have on our cars. I have an E46 M3 and I just changed out my OEM Catted Headers for a set of catless ones and I have had a real problem with the car having codes on the O2 sensors as well as many other codes just coming up even after I've done a tune that is supposed to adjust the sensors for that particular set up. Miss fire codes and strange stuff. Exactly what you have described and shown here. You were so thorough and I am so glad. I am having the miss fire codes just like you had on bank 2 but only on bank 1 cylinders. (Cylinders 1&2) indicating it is likely the O2 sensor on that bank (as you similarly showed) that is the culprit. It has shown a couple of times where both pre cat sensors are throwing codes. But usually it's only showing a code for the pre cat sensor on only bank 1. I have been thinking that it could be so many things that I just wasn't sure enough yet to pop for any one or two parts to try and solve it. I thought maybe vacuum or ground problems. But I'm sure enough now to start with this. Thank you again!
DANG!!! This was EXACTLY what I needed. Wow. Thank you SO much for this fantastic descriptive video. Now I know exactly what my problem is. I'm very excited to fix it now! Thank you !!!
I have a Mercedes W203 that was smoking a lot. I had no idea what to do. Thanks man. You saved my life (and my pocket).
I thought maybe it was leaky injectors but decided to do a bit more research before buying parts. glad I found this video. mine is running soo rich. crazy fuel smell and white smoke. thought it was leaky index 12s
will be changing these sensors, installing new coils and cleaning my plugs as the have less than 100 miles. changed them chasing a misfire issue. only 95k on motor and 106k on chassis
What was your fix?
Wow, ive been driving without 1 o2 sensor for around a year now since i put my DPs on. No wonder i have the same symptoms as yours.
Thanks for the detailed info on how to change the spark plugs. The steering rack removal was the key to this DIY. I bought the exact socket from FCP euro and it made the spark plugs much easier to deal with.
You mention using your affiliate link for purchases- and I’d LIKE to as you’ve been a great help to me and others, but I don’t see one for the “INPA K+D Can” cable. Please send or reply with the link because I’m about to start loading a dedicated laptop and will want to have the cable by the time the software is ready. Thanks for everything
Really happy I stumbled across this, I grabbed up a used BMW and it has the rough idle, as soon as I figured out it was about 30 seconds to a minute I instantly though heater, but since I am not familiar with BMW I figured it couldnt be that simple right? Well I will run this test in the am, and am doing a full drain and replacing everything anyways, just add the o2 sensor to the list
Thank you for your good service to humanity!
I can breathe now even with the garage door closed lol crazy dude
Fyi to save some money the o2 sensors are the same along as you get 2 rear ones (2 extra long ones will work but wont work viseversa... meaning two short ones obviously wont work and would cost way more for the short one vs long one meaning bank 1 vs 2 )
Great!!! I’ll swap mine tomorrow see if that works since I only get a misfire on 2 and it goes away only when I erase the core
uuu god i love you man... like the best teacher ever, i have exactly the same problem, but not the same tools :( ... but now i know what to do thanks to you... greetings from Chile!!!!
I started my car cold and engine started shaking right away. I hooked up a code reader and saw cyl 4,5,6 misfire. I let the car running for a bit more and then started seeing the o2 sensor code. So is it my o2 sensor or something else? When I clear code, I do feel that the engine smooths out for a few seconds.
I swear i love people like you who , i have i think the same problem at 325i 2008 n53 now bc i saw this video and i remember when i changed my sparkplugs and coils and i saw some of them was so dirty and some of them „clean“ like yours , i want to repair by myself what i can because here in Swiss if you go to a service they take to much for nothing and i hate it, but that s the reason exist people like you and youtube to try if we have enough time and we want this to try, big love man
P.s from where can i order a usb odb2 cable? Im not the best in cars or repairs but i want to handle what i have , thank you
Hi! I actually have the same problem on Bank 2 but I get low voltage values so the engine thinks it runs rich in bank 2. But it gets a little better when the engine has warmed up but still noticeable lower voltages than bank 1.
I haven't checked the spark plugs yet but i will.
I have the N53.
Great video. I like the logical trouble shooting. I’m having issues with my fan on a 93 300e which may have the same 3.2 engine???? My car was almost overheating at 120 while driving thru the McD take out line. The fan I think was off. I would think it should have been on at that temp. The fan was on yesterday. Are there two different signals to the fan??? One based on water temp and the other based on something else? Shouldn’t the fan be on at 120? I am suspicious of my wiring harness on the 93. It is the old brittle one. The wires near the temp sensor look a bit delaminated. Trying to figure out what to do. Don’t want to ruin engine. Probably gotta get that new harness in and hope that fixes it.
My voltages are all fine but I keep getting 2CAA Oxygen sensor heater function & 2CA6 Oxygen sensor temperature. All 4 are new sensors . Any ideas? I've tried harness, DME, adaptations, untwisting wires, fuses. Nothing!
If there is an intake leak your O2 sensor will not run same as the other bank. Did you check for air leak prior to comparing bank 1 to bank 2?
Love the education you give out. This is on my todo list.
You have MHD so you can see olso that bank 1 or 2 measure and if you monitor you can see in "graph a log" than is doing nothing it doesn't respons
Best and easiest Explained Lucy ! LOL
Have 630i n53, but there was loads of good stuff here to help me tackle mine.Thanks for uploading. Great.
You may have saved me money
I was about to order a new set of Delphi coils and 1 step colder spark plugz from fcp my car is running like yours at 2:47 😰
So ima get to ordering the O2 sensors and how to change one on my own
These air filters are positioned perfectly xD
😃 great explanation of the pre-cat I have a BMW E65 doing the same thing, tested with ista/d same result, is it possible a O2 can go bad in 3 years? Can something burn out the heating mechanism? Like a recent replacement trans? or a replaced generator?
Well I'm back about 10 months later and I have bought an E90 2008 335XI. (I still have the E46 M3 too). But I fear greatly that the O2 sensors need to be replaced on it as the car is having horrible cold starts with misfires on first 1 and 3 then if it is a bad cold start it's even more cylinders. One code read showed oxygen sensor code. The coils
What carly alternative are you using on your phone? I.m asking about both the dongle and the software. Thanks :)
Just learning here, bare with me... Cylinder 6 plugs appeared wet when you removed it. Is that gas? Also, will faulty O2 sensors cause gas to collect in the cylinder? Just trying to determine if I have a bad injector in Cylinder 5 (which I get a consistent misfire) or if my O2 sensor in bank two is bad. I have JB4 installed and three days ago I performed JB4 MHD BEF and car hasn't ran right since, primarily at idle/cold starts. I get a rich gas smell when idling.
I follow and another N54 content channels, but this channel is different! This is better! Absolutely useful DIY's!
1 NOV 2020
11:29am Central California
S.O.S
Bought a 2012 335i e92 n55 from this kid. He had it raced out with a vrsf catless downpipe, vrsf charge pipe & tuned with a MHD stage 1 tune. Fast forward, I gotta get it smogged. Took off the race kit, deleted tune, and put the stock parts back on. For maintenance purposes I installed new O2 sensors (i believe its 2 for this car), new spark plugs and ignition coils. Started her up, ran her for a good 5 days and I'm getting thus code.
Don't know what too do, help lol.
P0133: oxygen sensor circuit slow response bank 1 sensor 1. Permanent.
Good video and accurate information. Don’t stop making these types of videos bro
So my bank 2 is doing the same...but the rear one is also is at like .6-.8 but the front one goes to 3.8-4.1 volts! So are they both bad or the cat or why are these cars such a nightmare 🤣
Your video is so explanatory. Need help what inpa cable to use on 2009 335i n54. E92. there so many and some of them don’t work according to users just.
one of the best BMW N54 DIYer! look forward to seeing new video. BTW, will the post cat sensor be easier to change?
They are slightly easier to get to, the bank 2 sensor 2 sensor is actually pretty easy to access from under the car.
@@VehicularDIY I currently have all new o2 sensors and am going to put in soon and I was curious to know if I have to reset any adaptations or will the ecu just automatically dial in everything after replacing all o2 sensors
when you disconnect the sensor on a 318D, will it have the same effect? cause it also run bad only in idle and i don't get a engine light. greeting from Belgium! great video!
it's a N47 engine btw
You are awesome just wondering if you can show us a demo of the vanos on INPA please
Really great video. I need to check this on mine tomorrow
Thank you for a very informative video. Please could you tell us what is the app you running on your phone and on your laptop. Are they free to download or subscription based? Many Thanks.
Good video bro
It helps alot i have a audi s4 and couldnt figure out why it was misfiring i changed alot of stuff still the same. Next its the 02 sensors. Has all this syptoms
Thank you! 👍
it seems fine until I give gas , that's normal right ?
I can't pass emission test and I don't know why ... I assumed the o2 sensors but it seems right to me
I’m giving this a long shot in hope that you can reply. I’ve been having trouble with diagnosing my car since I bought an eBay inpa software but it is in German. Have very little computer skills and was wondering where you got your software from? I currently have a hp with windows 10
My all 6 plugs look black like that. Getting mixture too lean code only. Could both bank O2 be the cause ?
Hey thank you for this video, I'm currently changing out my turbos due to blowing a seal on one of them and my mechanic recommended replacing both pre-cat o2 sensors in a pair. They're quite pricey and I was having hesitation issues but attributed it to my wastegates also not sealing properly. To my knowledge the post-cats are ignored now that i'm catless but i will definitely check the voltage on my o2s prior to purchasing them. Also, im not sure if you know or not, but would xdrive vs non xdrive be a problem in regards to reaching the o2s from under the car? I know it's a tight space but worry that the subframe is in the way. Hopefully not!
I recently bought a 2013 BMW 335is 34k miles from Oregon (salted roads) I got codes for O2 sensors. One said too lean and the other said too rich. Are they really bad or could be something else? I have open recall for injectors getting it done in 2 weeks at dealer. Thanks!
Hi ! I have exactly the same problem I think on my x6M (s63)
No CEL, no hesitation on throttle, no error message , very slight instable idle, high fuel consumption, pop and bang on cold start, pop and bang on shifting with sequential mode, only black smoke (tail Pipes become black), car has +100k miles on the clock.
Do you think my oxygen sensor are faulty too ?
Nice work identifying the af sensor issue. Your long term/multiplication fuel trims are both very negative after the sensor replacement. Did you manage to find the cause and fix for that?
I have a 29E1 code that pops back up every day or so. I just keep clearing it to try to narrow down the issue. I have a rough start in the morning after it’s been sitting all night but otherwise my starts are pretty smooth. Once it warms up, it smooths out too. I thought maybe o2 sensor but if it doesn’t give me issues warm, should I look more at injectors instead? I have also gotten a cyl 5 misfire every now and then, so I’m leaning towards injector in bank 2.
Will it cause the limp mode in my 07 E70? I am having random limp mode regardless driving style/load/speed. I have replaced camshaft sensor, vanos solenoid, eccentric shaft sensor and disa valves. The code I pulled up is 2c31.Thanks
Are you using an OBD enet cable to code or to view parameters on your F15 like you are doing with your E90? I'm very interested because as well as you we own an E90 and a F15. Thanks in advance buddy!
Thanks for the information. Now I know how to check for bad lambda sensors.
Hi, could you please help, I'm a bit confused.
On my BMW N53 pre-cat sensor has a long cable and they are on the left side of the engien, after cat sensor has short cable and its under the car.
If I have the same reading like you wich one should I change?
Wow! Thank you, I have this issue... I appreciate this.
Hey man, which 02 spacer should I get for bmw b58 catless downpipe. Please send link, I am so lost 🙏🏾
I'm currently having a really bad misfire, getting 2c7c lambda behind and 2c2e in front of catalytic and cylinder 6 misfire. Would that mean both sensors on bank 2 gave out? I also have jb4 tune and can't get rid of code
Awesome troubleshooting help !
Thank you !
Stock air cleaner is better than that HOT air setup. I don't see why these are used.
I have same issue with a 2009 n52, 328xi. I've changed plugs and bank 2 coils. I'm trying to figure out if its the o2 sensors that are causing the misfire codes (only on bank 2) - and for some reason it says catalyst efficiency is below threshold?? on both cats. the numbers look ok for o2 sensors i guess, except on the bank 2 mix, it's adding a lot more fuel than its supposed to in the long run. little help?
I did just today change my downpipes to the original ones just to pass the TC.
And got those error, is it possible that this happend cause i put the oem downpipes back in( stage 3 and upgrade turbos)?
Have you ever had an issue when you start your car up and immediately your car starts to rev up and down repeatedly and when you step on the throttle it’s not responsive? When you put it on drive car still won’t accelerate but starts to jerk really rough?
2c7e oxygen sensor emissions control.upon starting rough idle, within 10 seconds it straightens out, but Engine running rich, you can smell the petrol. 2 oxygens sensors in the engine bay have been replaced, i take it thats pre cat, so now i need to replace 2 by the cats?
i’ve been running them backwards and running rich for about a month ugh i need to switch them! i forgot to mark them when upgrading to catless downpipes
How did you find that it is post catalyst sensor?
As always, very nice info and videos from you !
Can’t we just wire the exhaust flaps open or will that mess something up?
I'm having an odd issue with my n52, the bank 2 sensor is reading 0.29 volts while bank 1 is normal. I have replaced the sensor, but the problem is still the same. Help!
What code did it throw? I got a P0172. My guy said it’s an o2 sensor issue but I need to make sure.
I’m having a similar issue I put all brand new Coils and spark plugs but my cylinders 1-3 are still misfiring and my spark plugs are wet with gas when I take em out so you think my O2 sensor Is the problem .?
hey i did exactly what you did in the video. But im still having the same issue, ive looked everywhere online for a solution but im getting a lot of mixed answers. i was wondering if you could help.
Can you run INPA software to bmw 1 series f20 or f21 or just on 3 series
Wich program do you use to see all this data in your laptop?
I have a 2E32 code cylinder 3 I switched coils sparks and injectors can this be the issue?
I Have a question so I put in a new mass air flow sensor and the car started to run rough and won’t idle once i unplug the MAF it worked like normal well it idles as best it can. I do have a code for O2 lambda sensor and maf. I can see values
With my scanner when the maf is plugged in. So do I need to replace all the o2 sensors now that my maf works?
If could reply back. I would appreciate. It. I recently purchased a 2001 Honda Accord lx. I bought it from a family member and they put another motor(used) basically. When I start the car it’s fine. If I drive the car it only gets up to 45mph and it doesn’t have anymore power. It runs raggedy from the cold start but once I start it. But after the engine warms up it runs smooth. The code is air fuel ratio sensor. The guy that put the engine in says it’s the ecm computer could you help me out
Great video! I’m getting lean codes on my e92, so very timely. Thanks!
Can u paste here the part number for bank 2 pre cat lambda that u have replaced? I am about to buy one and I really dont want to get a different one :) I would really appreciate that
I have an 04 545i that gave a check engine that says increase emissions any idea what it can be ? It does smoke like urs did guessing its running too lean or too rich
Hi thanks for good information. Do u have to reset lambda control adaptations after the sensor replace?
Thanks, it would be a good idea.
Hello could you help rewire (solder which wire on which) n55 o2 sensor connector on lza07-hd3 ntk japan
This is Crazy I changed my O2 Sensor Bank 1 upstream. I'm still getting a low circuit reading PO131.. it may be poor fuel ratio. I also changed the EVAP Valve. Still Showing code plus I smell a lot of gas. I also have a little mis idle
Fuel filter
@@renzo1457 you think so
Have 2c7f and 2c6c oxygen sensor codes
Are they gonna cause any problems to the car? E90
I'm have what I think may be the same symptoms on my X5 xdrive50i. My code is 2D0D. Would you happen to know if this is the same? The code comes up on carly as air mass 2 Plausibilities or air volume 2 Plausibility.
Any help! Im getting fluctuation in after cat sensors. They are jumping.
What does it mean if down stream reads low in one of the banks?
I have an 2007 335i and I am getting a u30b7 any ideas on what it can be ?
Great video! I have a bmw 550i and it’s throwing a code P0175 running rich. Scanner shows
bank 2 short term trim -3.12, long term -23.44
Bank 1 short term trim -1.56,long term -6.25
Is it the o2 sensors causing it to run rich? Or can it be something else?
FYI it’s a 2011, 80k miles, I do burn a little oil.
Did you ever figure out what your fuel trim issue was or is, I have the same problem running rich on my e90 n52
@@dronevisiontechnologies2710 same! did you figure it out?
Thanks for the tutorial. Very well done.
Thanks Bro