How to fix the Lancer ignition switch

Cleaning and fixing the ignition switch of a mitsubishi lancer 2006.
طريقة تنظيف واصلاح فيبرة الكونتاكت لعربية لانسر بومة 2006

[@fookutube501]

YEEEEEEEEAAH ,nearly 2 years trying to figure out how to fix my starting problem when I open my ingition it was dirty asf....

[@guillermoblanco4060]

Thanks a lot. now i have an idea how to fix my lancer too.

[@egv152]

did it work?

[@PedroSilva-bx7ii]

Hello, tanks for this video I have exactly the same problem, I will try too fix it. 👍👍

[@natureloverbee8629]

Thanks allot, you saved mine $ 30. Love from Pakistan

[@danishawan6514]

Where did you find the starter in Pakistan? I am from rawalpindi, looking for parts of lancer 2007

[@jjoey30]

The problem is the brass plate wear down on contact thats y its not starting

[@mtrltoolman]

احسنت جزاك الله خير.

[@kicksoffs]

did you hear a clicking sound when you tried starting it or heard nothing cause i hear a clicking sound.

[@elBendary]

Heard nothing when tried starting

[@kicksoffs]

@@elBendary thanks

[@Propa_Way]

@@kicksoffsthat’s usually a starter problem when it’s clicking

[@teresahobbs2254]

My car has a similar issue but I can get it to start if I push the key in really hard as I turn it. Do you think it's the ignition switch or the cylinder switch?

[@elBendary]

I think it's the ignition switch

[@JuresseKabongo-i4y]

Bonjour, mon démarreur ne lance pas au niveau de clef de contact mais directeur le véhicule demarre

[@toinkyme]

You saved me $20

[@davidshaw4727]

Thanks for your help, good guidance.

[@joellajuett1060]

I may have same issue.
2006 Mitsubishi Lancer 2.0 SITUATION: When I was backing while turning the car stalled and would not start. Acted like dead battery or bad starter. I pulled starter and tested fine 3x at 3 different testing locations. Battery has full charge. When I turn key same thing bendix sounds to be kicking out and engaging but engine not turning. Tried multiple times and ground on battery starts to get hot. In the past I did have an issue with relay block under hood had come unmoored and fell near front tire and was collecting water and debris. Eventually the connections failed and I replaced entire block. I soldered all connections and heat shrinks over each one (retested today and all connections are good)
QUESTION: I understand if the car went start it may be that part in colum, but If the part your replacing in colum was my problem would it cause the car to stall. Also if that part fails will it allow starter to start to work but not completely?
Any help greatly appreciated

[@jestark0890]

Hi Sir, what grease or oil did you use for final coating of the contacts?

[@elBendary]

Vaseline or any white grease

[@pyen3526]

What if when it’s in accessory the lights on the dash turn on but when you turn it to on right before you crank it the lights come off, I want to say it’s a weak power output from the battery as in maybe my ground terminal is corroded

[@Wade-gt8kz]

Just lift key up as you turn key works every time it’s cause most pull down on the key when they start there nuggets.

[@kadeemconnor8923]

Hi my cs2 lancer turning the key but no start not even a click is it the starter or the key switch

[@amaldonador69]

Thanks for your help

[@jamiestonham]

What was the stuff you were dipping the cotton buds in to wipe the black part of the switch?

[@elBendary]

white grease

[@ibalaa1085]

احسنت

[@paoloyanutzzi1419]

Gracias, me acabas de ahorrar 35 $ que es el valor actual de uno nuevo, aqui en Venezuela el sueldo es de 7 $ Mensuales.

[@DanielAlvarezMaldonado]

Thanks

[@majdez6707]

اخي انا عندي لانسر 2001 وتعطل عندي القطعة اللي انتا الان تقوم باصلاحها وخايف اطلب القطعة من برا وتكون مش بتركب على سيارتي اتمنى لو تعطينا رقم القطعة بالضبط وهذا رقم شاصي سيارتي JE3DB36C61U771422

[@mohalaa3852]

ممكن رقمك للسؤال فني