Nicely executed project with Impressive Soldering skills. Seems you gave LED Heat Sinks a miss. It would have been a better Recycling project if the Old PCB ( CFL Bulb ) was used. The size could have been reduced a lil to push the PCB further down inside the bulb..more closer to the pins which could have resulted in some extra space. Instead of exposing the LEDs... It adds to the Glare as well. A Diffuser will make the THE difference. Regards, Sushil.
can we do this work on USA? i think the voltage is 110 right please confirm it is an awesome idea but as everyone said it is really necessary put a heat sink on it. great job very clever please confirm.
instead of making the circuit, just use a circuit from a phone charger, this one showed here has issues. and you can search it on google for 110 main to dc 5 volt circuit.
your video is very good, but without voice, how i learn about the component names which use it to convert CFL into a 40 watt LED Bulb, the same video again upload with voice so that we can understand the components names and its fittings, hope you again upload the same video with voice and components name and circuit plate where available, thanks for again upload with voice?, Allah Blessed you always!!!!
Please change the circuit Diag at 1:08, it is incorrect with reference to the final product. There are only 4 no's IN4007 used in actual, whereas in circuit you have updated it is 5 no's. In circuit, there is only 1 10 ohm resister used, where in the actual , 2'nos used. Please update. Wonderful job.... As commented by other's what is life time you are getting, as other's pointing that the LED life time would be very short s there are NO heat-sink's. Thanks Mohan.S
Whole reason i looked at the comments. Those led’s will straight melt the hot glue and make it drip all over within minutes.. i used two forks i sanded down and jb weld to hold fork tops against the back of the leds to not short em out. But yee, it forkin worked.. fork yea it forken worked, what is it not forking believable a forkin fork worked? Fork off then.. Ha.
Exactly! He could have used the copper face of the breadboard as heatsink and place the components on the other side. It would have been such a neater job.
how about how to decide the watt of the bulbs to attached,and which component decide watt of the bulbs can u give us in details, & if u can then it'll be Osama,bye the way well done brother keep it up ci yo
i used 4 leds of 1 watt = 4watt. you can use more leds for more watts for increse brightness and leds you have to increase value of the series capacitor and mount leds on a heatsink. thanks.
Why have you not used a heat sink. Or why is it you did not use any heat sinks? Or. I am pondering as to what the reasoning is behind your non existant use of any heat sinks for the dissipation of the heat generated as a byproduct of consumed energy from the led’s which you used in this project kind sir?
Have tried the same circuit on breadboard ....... But Output Voltage is very low I have bought new LEDs but they are so dim What I have tested I'm getting only 2 volts at the output If U know the reason ...... Kindly let me know :)
voltage ko kam karne k liye capacitor lagaya hai series me. Due to capacitive reactance capacitor reduces ac voltage then we need a rectifier to convert ac to dc. Thanks.
Are bhai transformer ki zarurat nhi hai yaha pe pehle video dyan se dekh aur jankari hasil kr electronics k bare me. Aur bulb jal raha h ye bhi delh le.
hello bro i love your videos
+Nadim Sarwar thanks.
this I
will help rural technicians for better earning and serve people. ve.ry good .effort that u shared this knowledge. god bless u
Wow very interesting, usefull creatifity, good 👍👍👍
Nicely executed project with Impressive Soldering skills. Seems you gave LED Heat Sinks a miss. It would have been a better Recycling project if the Old PCB ( CFL Bulb ) was used. The size could have been reduced a lil to push the PCB further down inside the bulb..more closer to the pins which could have resulted in some extra space. Instead of exposing the LEDs... It adds to the Glare as well. A Diffuser will make the THE difference. Regards, Sushil.
very good nisar bhai
बहुत खूब बना
brilliant idea!!!!!!please try to upload some other videos like this..........
hello sir i like your videos
good luck with your company
very good idea
Esta muy maja, pero el problema que le veo es la disipación de los leds, por cierto, yo le pondría 3 cálidos y uno frío.
can we do this work on USA? i think the voltage is 110 right please confirm it is an awesome idea but as everyone said it is really necessary put a heat sink on it.
great job very clever please confirm.
instead of making the circuit, just use a circuit from a phone charger, this one showed here has issues. and you can search it on google for 110 main to dc 5 volt circuit.
yes you can do it if you have ontan charger
Good and appreciable work
thanks for the reply
can u please tell me which capacitor i will use in place of .22 micro farad.
+Abhishek Shiwatch
You can use 1.2uf 400v or 2uf 400v capacitor.
which music did u played in video? kind of trippy awesome
is it diodes withstand for 230vAC voltage...?
+MADHU BABU 1N4007 diodes rated for 1000 volt
+Technical Nisar k thank you...
Good
bro u r just pro in soldering
your video is very good, but without voice, how i learn about the component names which use it to convert CFL into a 40 watt LED Bulb, the same video again upload with voice so that we can understand the components names and its fittings, hope you again upload the same video with voice and components name and circuit plate where available, thanks for again upload with voice?, Allah Blessed you always!!!!
Please change the circuit Diag at 1:08, it is incorrect with reference to the final product.
There are only 4 no's IN4007 used in actual, whereas in circuit you have updated it is 5 no's. In circuit, there is only 1 10 ohm resister used, where in the actual , 2'nos used. Please update.
Wonderful job.... As commented by other's what is life time you are getting, as other's pointing that the LED life time would be very short s there are NO heat-sink's.
Thanks
Mohan.S
is ka bulb alg se milta hai kya bro
heat sink tell me about that and nice idea
wow it's awesome bro....
which led did u use 1W or 3W
Is it the glue still hard when getting hot from the led while the led on??
nice idea but can you tell me how many minutes your LEDs lighting?
Nice vedio
Nice Bhai reketifayr kaise chek kare ge
good job
how did you remove the tubes & cleared the holes?
neat and nice
Nice video sar
one 105 or 205 capacitor provides a 87-120 mA current LEDs will be wrong easily. you should add a zenner for output voltage stabilizing!
15 ma
Very nice
nice it's working
Such
nice idea
Nice sir please aap isaka warking dal sakate hai
nice video brother
good idea....
Useful kwalage to save money
Can u make a video with anchor cfl ......
can you give me the list of products used in detail
+Princy Antony pls. Check this link for detail.
Hello sir this led used aa 220voltage aa no tell me plz thank u
not easy bhai aap jaise expert hi kar paoge
Mass bro
Plz, provide led details and buying site
without heatsink how can it work
How many watt it will be consume?
There is a difference between the circuit diagram and the actual circuit assembled in the video. Which one is correct ?
both circuits are correct. you can use several led's in parallel.
don't you mean series?
GOOD PROJECT
Thik hai. lakein bhai led heat honey per kharab ho jatee hai koi naya idea batao jisesay ye jayda din tikau rah sake
plz tell ,me can do with the fuse bulb?
or plz tell me the things needed? it that much only shown in videos
fuse cfl can be used
but check all component is in good condition
What is the purpose of that 0.22uf 400v capacitor
nice bhai
bro ye green wali kitny ohm ki resistance lagai ap ny
mobileake s 10 ohm
u have forgot the heat sink for that LEDs...
Whole reason i looked at the comments. Those led’s will straight melt the hot glue and make it drip all over within minutes.. i used two forks i sanded down and jb weld to hold fork tops against the back of the leds to not short em out. But yee, it forkin worked.. fork yea it forken worked, what is it not forking believable a forkin fork worked? Fork off then..
Ha.
Exactly! He could have used the copper face of the breadboard as heatsink and place the components on the other side. It would have been such a neater job.
Thanks
how much volt bulb are u using??
in the price of a charger I can get 2 led blub easily... anyway keep it up..
Bhai ue bulb jo aap ne lagaya hai yah bulb ac hai ki dc
the bulb which I have is same that of Philips but I'm not able to remove the outer part plz tell a short cut to do it ...
how about how to decide the watt of the bulbs to attached,and which component decide watt of the bulbs can u give us in details, & if u can then it'll be Osama,bye the way well done brother keep it up ci yo
i used 4 leds of 1 watt = 4watt. you can use more leds for more watts for increse brightness and leds you have to increase value of the series capacitor and mount leds on a heatsink. thanks.
nice work bro keep it up
Hi, Can you provide description like Voltage Current and Wattage please. Thanks
Hello sir this led used aa 220 voltage yes aa no tell me plz
How is the output voltage that is produced from rectifier circuit?
Thanks at first.
Sir r u explain why 10 ohm resistor is connected ?
bulb connection parallel or series
Hello.
Led bulb which watts??
Led bulb price how much ruppey and also easy to buy which site link plz reply
Good work bhai
Mohamad Salamat l
Mohamad Salamat
Can you list the things
Super
nice
sir muje ye bataen k doid ki kon si side aapas me milani ha plz sir
iqbal aslam.
Wow its working bro..
awesome
Nice
Sir, how you calculated the values of components like resistor and capacitor.
Why do you have not use heat sink
Why have you not used a heat sink. Or why is it you did not use any heat sinks? Or. I am pondering as to what the reasoning is behind your non existant use of any heat sinks for the dissipation of the heat generated as a byproduct of consumed energy from the led’s which you used in this project kind sir?
Bhai ager 4 se zada bulb lagane hoto fiting isi tarha se hogi
Yar nisar bhai green wire k baray main batao. Plz
I think dc positive / negative?
Green wire is negative -
Technical Nisar , can i use adoptor circuit? And how much output power will get from nokia/ samsung charger?
Isme capacitor kitne volt ka lgta hai
bhai heat sink bhul gai kya?
bhai yeh 25V 100uf capacitor kaha milegi
I mean pehle aapne jo kharab pcb se diode ni kala tha is pcb me yeh capacitor milegi kya
Plz reply bhai
You can buy it on amazon or other internet web site
bhai is circut ka output kya hai ??
what is the functionality of 1M ohm resister in parallel with .22uf capacitor because you have not used that.
its for safety. after switch off the device capacitor remain charged. to discharge capacitor automatically i used the resistor in series. Thanks.
It will not work for a long time after some running these LEDs will get damaged by heating
Sk electronic{Dhamtan sahib } Haryana
SUNIL DHIMAN. sir Ami R p Ami Anna ke janey j
+Dj Rp hi
vai resistor kitne ka hain?
What is that led...?
Have tried the same circuit on breadboard ....... But Output Voltage is very low
I have bought new LEDs but they are so dim
What I have tested I'm getting only 2 volts at the output
If U know the reason ...... Kindly let me know :)
diodes se pehlay 220/6 transformer use krle.. diodes sirf ac to dc krti hain, voltage kam nahi karti hain
Me bhi yahi soch rha tha...
voltage ko kam karne k liye capacitor lagaya hai series me. Due to capacitive reactance capacitor reduces ac voltage then we need a rectifier to convert ac to dc. Thanks.
Are bhai transformer ki zarurat nhi hai yaha pe pehle video dyan se dekh aur jankari hasil kr electronics k bare me. Aur bulb jal raha h ye bhi delh le.
nafice ahmad ahh sorry i got it.
bhai ye bright led kitne ki rupay ki hai or kidhar milti hai
plssss reply karo
you can find nearest electronics repair shop rs. 2 or 3.
Goodmorning.safsri
Iski brightness bohot limited time k lie he bcos isme heat since nhi he. But !dea mast he.
awsum concept.
what's the value of the two capacitors ?
It's working
Bhai ye led light kha par milti hai price kya hai
nice, but how many times you got burnt your fingers and thumbs ? :)
Use heat sink for leds