How To Install ICON Lift Kit On 2010-2023 Toyota 4Runner
HTML-код
- Опубликовано: 15 ноя 2022
- In this video, we show you how to install the stage 1 lift kit from ICON. Taking the OEM suspension out and installing the new. Also the height difference you gain with the ICON stage 1 vs OEM. For a more level ride height I would suggest getting the coilover wrench from ICON so that you can lift the front a bit more than how it comes out of the box. Overall an easy install and rides nicely. As always, after any suspension modification, you should get an alignment. Thanks for watching! Link for lift kit is below.
▼Shop the Products featured in this video!▼
yotaxpedition.com/products/st...
Our Website and Socials
Website | yotaxpedition.com/
Facebook | / yotaxpedition
Instagram | / yota_xpedition
Tik Tok | / yotaxpedition 
Авто/Мото
its nice when everything is brand new and there is no rust .. LOL good work..
It definitely helps lol
Great job, one of the better install videos I’ve seen. Keep up the great work 👍
Thanks!
I currently run this kit on my 5th Gen TRD OR. The ride is more firm than factory but not stiff, even with the front adjusted close to max height/pre-load. I went with bilstein 1.5 -2” rear lift coils instead of the 2” icon. A slightly shorter spring which gave me near exactly 2” of lift in the rear, opposed to the 2 1/4” that the icon 52700 2” lift spring gives as mentioned in the video. Overall, happy with the ride height however if I were to do it again, I would spend a little more money on a higher end setup, something like kings with remote reservoirs, or even the Icon Stage 2. This is a great entry level setup, but if you’re anything like me and are getting into overlanding/off-roading you may outgrow this setup rather quickly. And reselling used suspension components isn’t easy. Cheers!
Good feedback! But I'm sure this kit wont be on for too long. Not because its a bad set up but because we are constantly trying new products that we offer on our website. The icon stage 1 kit is definitely a great entry level kit if you want a adjustable coilover.
Are you selling?
Good content!
Thanks!
Nice simplified video. Not to nitpick, but I'm skeptical you'll get it aligned without new upper control arms. Also, you need to extend your rear bump-stops, add longer rear end links, and fix that track bar (panhard ) angle with an extended bracket. Lifting a vehicle is a slippery slope...
Still doing a lot of research here - thanks so much for the vid. This install doesn't look too hard and you explained it super well without unnecessary information.
Are the sway bar spacers effectively a front differential drop? Also, do the front coilovers rub on the factory UCA's?
No rubbing on the UCA's. The sway bar spacers are different than a diff drop. The sway bar spacers are to relocate the sway bar forward a tiny bit to avoid hitting the new coilovers.
Great install vid. I have a 21 4runner off road w/kdss. Is there a trackbar needed to complete the install? Looking at an icon stage 4 kit, and just buying a separate trackbar to avoid hitting the higher priced stage 6-8 kits w/trackbars included.
cheers
** stage 3. and ahhh yes, jumped the gun without reading the comment replies. Saw the rear trackbar 54200 needed, and no spacers up front. 🤘
Would I need a differential drop kit for the front and a new track bar correction panhard kit to return the track bar to its original horizontal design for the rear?
Would be recommended to add new upper control arms that work better with a lift kit? I'm thinking about buying the Icon stave 1 but want to make sure that I won't run to any issues down the road.
Diff drop isn't necessarily needed. Track bar correction and upper control arms are always good to add after a lift kit to just help with alignment and ride quality.
Great video! You may have covered this but, are you still running stock tire size?
In this video we are on the stock tire size (265/70) but we did upgrade to some mud terrain tires from Yokohama.
@@yotaxpedition Nice. I think it looks ok with stock.👍
I’m installing the same icon lift kit and also ordered the trd skid plate from yoda xpedition but the pre installed front bolts on skid plate are too short with the added spacers on mounting brackets!! What do I do?
Hey Seamus, we had to add spacers to our TRD skid plate on the 2 front holes and get longer bolts. The bolts we used were m10x1.25 60mm long.
Work with kdss? Also is there a need for diff drop kit? Or high angle cv boots?
This kit does work with KDSS. Just don't install the sway bar spacers that come with it (those are for non KDSS). You will be fine with out a diff drop. The CV boots would be a better route
Why no upper control arms?
I would like to see a stage 4 install video
Might be something we cover in the future.
I’m undecided, for 4Runner TRD off road 2021 coilovers RC vertex or this kit. Which one would you recommend?
We have no experience with the RC Vertex kit, though they look nice. The ICON kit we've had on our 4Runner now for probably 8-10 months and we have no complaints. Went on a few offroading and camping trips and it performed well and also rides nice on the road.
Thank you very much for responding! You have very interesting videos 👍🏼
So if i delete my xreas system i can install any lift i want? Is that correct?
Correct, but the Icon kit in this video will work with kdss models but there is a few other steps to the install. Do not install the front sway bar relocation brackets and you need the 54200 track bar as well.
You said they sent it in the best possible set up. Do you remember what they had the front set to when you got the kit?
In this video, we installed the kit exactly how it came.
Did you guys upgrade the rear springs to overland springs?
52700 is the part number from ICON. They are the standard springs that come with the stage 1 kit.
With this lift and vipercut can u put 285? 34s
Yes we currently have 285/70s on the 4Runner with this lift.
what size tires are shown in the video?
These are 265/70/17 mud terrain tires from Yokohama
Shoud you get a new Upper control arm after lifting
It is not necessary but recommended
Do I need new UCAs if I get this suspension?
It is not needed but would help to get your suspension geometry back to OE spec
What tire size are those?
265/70/17
Is this lift kit KDSS compatible?
Oop nevermind you already answered this. Have you had any issues with the kit since installing it?
No issues, still installed and performing great
What's the total cost and how's the quality of the suspension lift?
The total cost for the kit is going to run around $2000. But we currently have this kit at 15% off for black Friday. Quality is good, and installation isn't bad. I personally would also get the coilover wrench to go with it to make the front level with the rear.
@@yotaxpedition ty
@@monkeypolice3048 Anytime
Correct me if I’m wrong but if you make the front level with the rear based on ground to fender won’t you have reverse frame rake since the rear fender is cut out higher then the front ?
Interesting I saw one guy just lose the control arm and remove the bolt connected to the wheel, remove the bolt to the shock, control arm swings out of the way. Then remove the three bolts on top of the shock and shock drops…
There's more than one way to do it.
In the back you said you gained 2 1/4 inches, but from 37 3/4 to 39 is 1 1/4...
You're right...must've had a brain fart.
My thoughts exactly
Have you ever installed one of these Kits on a 4Runner with Xreas Suspension ?