[DIY] How to make the F clamp 100 times easier to use. $1 or less to modify.
HTML-код
- Опубликовано: 6 сен 2024
- Hello.
Thank you for watching.
There are many other modifications of this F clamp, but I have not seen a flat steel welded type, so I introduced it. I've been using this flat steel type for about two years since the prototype, and I think it's really wonderful. No damage to wood. Of course, if you tighten it with a lot of force, there is a risk of marks, but that is the same with any clamp.
I own clamps from various manufacturers, but in terms of scratch resistance, it is superior to any other product.
It is thought that the reason for this is that the flatness of the part in contact with the material is extremely high and the fixed surface is wide, so that the force is distributed appropriately.
Another feature is that the material does not move easily when tightening. In the normal case, the material tends to move in a circular motion when tightening, but in this model, the plates face each other and hold down, so the material does not move in a circular motion. almost unaffected by
So far, we have repeated various modifications and prototypes, but the most excellent model, including cost, difficulty, and functionality, is this version, and if you can do metal processing and welding, you can easily make it. think.
Even in metal processing applications, it is advantageous not to increase the number of unnecessary scratches on the material, and the wide area to be pressed also suppresses local dents and distortions. By using magnetic tape, you can temporarily fix the main unit, so you can expand your ideas for how to use it. This model is not only for woodworking, but also for those who work with metal.
If welding is not possible, lumber can be used instead of flat steel to achieve the same functionality. However, in terms of strength, it is unavoidable that it is inferior, but if you use it for woodwork, it can be used sufficiently, so if you are interested, please try it. If you put an antibacterial cutting board on it, it will be more resistant to scratches.
Also, when using wood, the dimensions of the material should be slightly longer to make it easier to attach hot bonds.
Also, as a non-welded model, there is also a version using a cola cap, so please take a look.
The work of layering baking soda is surprisingly interesting.
• 【100均 ダイソー】♻️ F クランプにコ...
--------
important point
Be sure to point the welds. Then, each of the upper and lower plates is fastened in 3 places.
reason
1) Minimize thermal deformation.
2) It can be removed by scraping with a grinder.
3) High strength is not required.
4) Welding may come off if there are only 1 or 2 points.
Any anti-scratch plate will do. Here's what I've tried and the results.
● Rubber sheet.
The double-sided tape slips and the rubber sheet slips. It does not damage the material at all.
● Antibacterial cutting board
Although the resistance value is a little low, it is recommended because it has the best balance.
● Aluminum sheet
It will prevent scratches, but there is no merit because it is soft.
●Magnet tape
For steel. There is no benefit for woodworking.
Please remove the protection plate when using in a place where the temperature becomes high due to welding.
Also, if you want to use it in a place where heat enters, it is recommended to increase the thickness of the steel material. If it is 3mm, it may be distorted by heat.
that's all.
Added a drawing to the community. Please refer to.
www.youtube.co...
Please give me a high rating and channel registration.
Language translation uses Google's automatic translation. Please excuse me if it is difficult to read.
#Handmade woodworking tools
#f clamp for woodworking
#tools
#tool
#woodworking
#woodworking tools
#fclamp
#f clamp
#clamp
初めまして。廉価な商品を工夫して使いやすくする動画、大変参考になりました。さて、お伺いしたいのですが
この商品のクランプ部の素材は鋳鉄かと思うのですが、溶接は半自動ですか、それともティグ溶接ですか？
鋳鉄はは溶接が難しいと聞きましたので、その効き具合をお聞きしたいです。
はじめまして、こんにちは。ご視聴頂きありがとうございます。ご質問の件ですが、この動画では、中国製のTIG-200P と言うTIG溶接機を使用しております。
ここでの溶接は、基本的に仮止め程度の点付けで処理しており、簡単に鋼板が外れない程度で十分だと考えています。また最も優先したいのが、鋼板のフラット性で、熱の入れ過ぎによる歪みを抑える意味でも、全面の溶接はしていません。それに点付けなら万が一の時も直ぐに外せますしね。
ただ、グリップ側のカップの材料が薄いので、ここを溶かし過ぎて穴を空けないように気をつけて下さい。私の場合は、先に鋼板に熱を入れて溶けたタイミングで溶接棒を入れて、カップあるいは、本体の鋳鉄に熱を入れて素早く留める感じで行っています。なめ付けだと難しいので、必ず溶接棒を入れた方が良いと思います。(達人は別として)
クランプでしっかり鋼板を挟んで溶接できますし、仮止め程度の点付けなので、色んな溶接方法でも対応可能かと思います。是非、お試し下さい。
詳細な返信ありがとうございました。当方もTIG溶接機は持ってはいるのですが、アルゴンガスの設置に
二の足を踏んでいて、未だ使用できません。
鋳鉄の溶接は棒溶接でやや高額な溶棒でないと難しい、とネットにありましたので
通常溶接ができる情報はありがたいです。ただ、TIG溶接ではなく半自動で挑戦したいと思います。@@DIY_QUEST
確かにアルゴンガスの導入は、敷居が高いかも知れませんね。
当方も、始めに導入したのは半自動でしたが、フラックスワイヤーが高いとか、作業時のワイヤー詰りで中断されたりがあって TIG へ移行しました。適正な下処理と設定で行えば、半自動でも十分可能だと思います。
そうなんですね。今回はありがとうございました。@@DIY_QUEST