Quick tip, whenever you remove the first film from the tray, never hold the tray facing up as dust particles can land the film, as you remove the film twist and face it down. Also your voice reminds me of Nicholas cage lol
i remember when you had to line up the screen protector on phone and air bubbles, but spigen sorted it so easy to install now. only use them for screen protectors and lens protector,using ESR kick stand case,used to be all spigen for my iphone 15 pro max 256gb. enjoy.
Unlucky with those two pieces of dust, it’s more tricky doing it whilst recording and doing a voice over though. Because the two bits of dust are near the edge, you’d probably get away with lifting it carefully with a finger nail,making sure not to touch the side of the protector that lays down on the screen, then use the sticker to grab the two offending pieces of dust, then drop it back down. If you’re very careful, and quick at the same time you may be able to rescue the situation!👍🏻 I’ve been fitting these spigen ez fits since the iPhone 11 Pro Max I think, had them on every iPhone up to my latest phone(14 pro max) going to fit one to my 15 pro max which I’m getting in two days time. Never had a problem with these screen protectors, so easy to fit perfectly straight, no bubbles, no lifting even after 1 year being on my phone😁 Ps I wouldn’t use the lens protectors, as someone else said, it will eventually effect picture and video quality, when the plastic scratches up, then your expensive camera lens are looking through cheap scratched plastic.
Same thing happen to me on both screens, a little dust/strand thingy in the bottom right both times! Lol You can't really notice it when the screen is on, but it still bothers me a little. I'll order another set and keep them ready for when it bothers me too much.
I also got dust underneath both spigen screen protectors for my 15 pro Max. I went through a painful, tedious process of lifting it up with my fingered nail and putting dust removal stickers underneath to get all the dust out. Every time I would remove some dust more dust would get underneath in other spots. However I was very patient and worked very hard during this process and now there is basically no dust underneath anymore. My hard work and dedication paid off.
I've gone through 2 different types of screen protectors for my iPhone 15 pro, the first was an edge to edge screen protector that went with the curviture of the screen. This looked great until I tried putting on the spigen tough armour case. The rubber edge then bumped into the screen protector and lifted it around the edges leaving huge bubbles that could not be removed with the case still on. So I tried a different screen protector, like the spigen in this video, its not edge to edge and fits within the bezel. Now I hate the white, raised outline I see, like in this video of the protector screen's edge. :( life was so much easier with a flat screen non pro iPhone.
I just got mine and I did install it , but I did not ordered Spigen . I got myself a Torras one ( never heard of them before ) . Easy to install and it has really thin black edges so you can`t see the white outline . My case is a Mous Limitless 5.0 and fits perfectly , hope this helps ,
How is this full face screen protector when it is the EZ FIT Version??? Ithought this version has a liitle open up free space on top which doesn't cover the front camera. Is align master better?i dont understand...
Still waiting for someone to film this not from the top, but from the side, where dust and stuff from you, ceiling, lights, etc. fall onto the screen, It's tough to film. But thanks for the effort! Did you consider the Apple and Torras versions?
I didn’t look at the Apple or Torras versions. I had a great experience for the screen in my Model Y, with the frame, and realized that Spigen offered a similar solution for Apple devices, and decided that was the direction to go.
@@paulchiu there’s definitely a noticeable lip. It’s not sharp, but you can definitely feel it. But that’s only if you’re not using a case. I’ve got the Wirecutter pick, the Smartish Gripmunk, it’s super thin - but has enough of a reveal that I don’t even feel the edge of the screen protector with the case on.
@@paulchiuI’ve got this exact ez fit screen protector for my 14 pro max, and had it on my older 11/13 pro max aswell. With a case on you don’t feel the screen protector when swiping from the bottom, just the edge of your case.
@@GillTechGroup I went to the Apple store to pick up my 15PM and witness a few Belkin installations at the store. Like the feel of the protector but the edge were a lot short of the 15PM's edge. So you see a bump and accentuated with the present of any case. With that, I bought the Torras with the light black frame and true edge to edge coverage. I made a video ruclips.net/video/LjYKx2VljyI/видео.htmlsi=g1Ti0cy5brzy9azV
i ordered a screen protector from a different brand yesterday for the IP15 pro max but after more and more bad reviews on amazon appeared i ordered this Spigen one today and now also negative reviews appear :) People say my old one is to large and the case will push the screen protector off the phone. About the spigen they say its to small and the edges are not rounded which would look cheap. I will see tomorrow but i guess it will be bad :) By the way, are you sure your case was correctly snapped in ? It looks like the right side hasnt even popped in ? The back camera glas protector is nice but the case will also lift it up when you remove the case.
Yeah there’s definitely more of a lip than I’m used to. With the case on I don’t feel it. The one negative, it seems to get all my pocket lint from my jeans. Past protectors didn’t have this issue. As for alignment it looks perfect. I’ve taken off my case a few times and no issues with the camera lens protector. I suppose if your case has issues, that’s what the individual lens protector style is for.
@@GillTechGroup yeah that is exactly why the Spigen protector is not so good, because its like a lint trap but the others are to big which causing the other problems of not sticking to the display in the outer areas. I had a camera protector in the past on my IP 13 pro max and i liked it because kin dof similar problems, the three cameras are a dust trap as well and with the protector no dust can come between the cameras.
Do the lens protectors affect the image or video quality, as it's been 2 weeks since the video came out; can you give me a detailed review of the lens protectors themselves. Looking forward to a response.
When the flash is on for either a photo or a video. I feel like it washes out the image. It’s definitely noticeable. I wonder if the individual lens protectors solves this issue. Otherwise I haven’t noticed any decrease in image quality. I’ll see if I can figure out the best way to do a video to show this.
Damn bro you made this so difficult for yourself. Open room, remove screen sticker fresh from box and add the protector instantly. Why you removed it then let it sit to catch dust is beyond me
Yeah! Less than ideal. In the past I’ve put it on in the bathroom while running the shower on hot, so the steam helps knocks the dust down. Would’ve been a lot harder to record there. It was wild though that there was dust inside the box already, maybe from the paper packaging?! Got any tricks for me?
Bro, just lift up the screen protector slightly with your fingernail and use the dust removal sticker. You can easily get the piece of hair out by doing that.
Thats easy use the adhesive tape while tilting the screen using ur finger then slide the adhesive tape under the tempered glass and target that dust. Thank me later
It's a Smartish Gripmonk. It's the best rated case from Wirecutter's reviews, and I actually like it a lot. You can pick one up here amzn.to/404suw6 #ad
I snagged mine off Amazon. Here’s a link: amzn.to/46oGe72 #ad They also have an Apple Watch Ultra/Ultra 2 protector that I picked up, and made a separate video of. Here’s a link to the protector for the Ultra amzn.to/462rLOo
I had a iPhone 14 Pro with the same model screen protector, and it worked great. When I put this one on and removed the bubbles, it didn't align properly with the curvature of the rounded edges at the top and bottom of the iPhone screen. I guess if I had a case with thick bezels, I wouldn't notice it. It would be interesting to order the new model AGL06874, and see if there are any differences. @@GillTechGroup
Спорт
Quick tip, whenever you remove the first film from the tray, never hold the tray facing up as dust particles can land the film, as you remove the film twist and face it down. Also your voice reminds me of Nicholas cage lol
i remember when you had to line up the screen protector on phone and air bubbles, but spigen sorted it so easy to install now. only use them for screen protectors and lens protector,using ESR kick stand case,used to be all spigen for my iphone 15 pro max 256gb. enjoy.
Literally got the exact same phone last night and the screen protector in the morning next day congrats
That’s what’s I’ve been doing lately getting everything on before i even turn on the phone
Unlucky with those two pieces of dust, it’s more tricky doing it whilst recording and doing a voice over though. Because the two bits of dust are near the edge, you’d probably get away with lifting it carefully with a finger nail,making sure not to touch the side of the protector that lays down on the screen, then use the sticker to grab the two offending pieces of dust, then drop it back down. If you’re very careful, and quick at the same time you may be able to rescue the situation!👍🏻
I’ve been fitting these spigen ez fits since the iPhone 11 Pro Max I think, had them on every iPhone up to my latest phone(14 pro max) going to fit one to my 15 pro max which I’m getting in two days time. Never had a problem with these screen protectors, so easy to fit perfectly straight, no bubbles, no lifting even after 1 year being on my phone😁
Ps I wouldn’t use the lens protectors, as someone else said, it will eventually effect picture and video quality, when the plastic scratches up, then your expensive camera lens are looking through cheap scratched plastic.
Same thing happen to me on both screens, a little dust/strand thingy in the bottom right both times! Lol
You can't really notice it when the screen is on, but it still bothers me a little. I'll order another set and keep them ready for when it bothers me too much.
I also got dust underneath both spigen screen protectors for my 15 pro Max. I went through a painful, tedious process of lifting it up with my fingered nail and putting dust removal stickers underneath to get all the dust out. Every time I would remove some dust more dust would get underneath in other spots. However I was very patient and worked very hard during this process and now there is basically no dust underneath anymore. My hard work and dedication paid off.
I've gone through 2 different types of screen protectors for my iPhone 15 pro, the first was an edge to edge screen protector that went with the curviture of the screen. This looked great until I tried putting on the spigen tough armour case. The rubber edge then bumped into the screen protector and lifted it around the edges leaving huge bubbles that could not be removed with the case still on. So I tried a different screen protector, like the spigen in this video, its not edge to edge and fits within the bezel. Now I hate the white, raised outline I see, like in this video of the protector screen's edge. :( life was so much easier with a flat screen non pro iPhone.
I just got mine and I did install it , but I did not ordered Spigen . I got myself a Torras one ( never heard of them before ) . Easy to install and it has really thin black edges so you can`t see the white outline . My case is a Mous Limitless 5.0 and fits perfectly , hope this helps ,
Very smart choice screen protector it’s greatly priced and not from Apple Store which are overpriced
That dust is bothering me bro, please change it
😂😂😂
How is this full face screen protector when it is the EZ FIT Version??? Ithought this version has a liitle open up free space on top which doesn't cover the front camera. Is align master better?i dont understand...
Bro i think your iPhone might have some of the paint chipped on the titanium finish on the edge of the top speaker.
does this cover the ear speaker as well? :)
Those two pieces of dust probably sticked to the screen protector while you were holding it like that 6:31
Yep, have to rotate as you peel and leave the exposed side facing downward.
Yep it should be quick install after peal the plastic of screen protector because it will take a lot of dust by a sec
Still waiting for someone to film this not from the top, but from the side, where dust and stuff from you, ceiling, lights, etc. fall onto the screen, It's tough to film. But thanks for the effort! Did you consider the Apple and Torras versions?
I didn’t look at the Apple or Torras versions. I had a great experience for the screen in my Model Y, with the frame, and realized that Spigen offered a similar solution for Apple devices, and decided that was the direction to go.
@@GillTechGroup How does the edges feel when you swipe up to unlock? thanks.
@@paulchiu there’s definitely a noticeable lip. It’s not sharp, but you can definitely feel it. But that’s only if you’re not using a case.
I’ve got the Wirecutter pick, the Smartish Gripmunk, it’s super thin - but has enough of a reveal that I don’t even feel the edge of the screen protector with the case on.
@@paulchiuI’ve got this exact ez fit screen protector for my 14 pro max, and had it on my older 11/13 pro max aswell. With a case on you don’t feel the screen protector when swiping from the bottom, just the edge of your case.
@@GillTechGroup I went to the Apple store to pick up my 15PM and witness a few Belkin installations at the store. Like the feel of the protector but the edge were a lot short of the 15PM's edge. So you see a bump and accentuated with the present of any case. With that, I bought the Torras with the light black frame and true edge to edge coverage. I made a video ruclips.net/video/LjYKx2VljyI/видео.htmlsi=g1Ti0cy5brzy9azV
i ordered a screen protector from a different brand yesterday for the IP15 pro max but after more and more bad reviews on amazon appeared i ordered this Spigen one today and now also negative reviews appear :) People say my old one is to large and the case will push the screen protector off the phone. About the spigen they say its to small and the edges are not rounded which would look cheap. I will see tomorrow but i guess it will be bad :) By the way, are you sure your case was correctly snapped in ? It looks like the right side hasnt even popped in ? The back camera glas protector is nice but the case will also lift it up when you remove the case.
Yeah there’s definitely more of a lip than I’m used to. With the case on I don’t feel it. The one negative, it seems to get all my pocket lint from my jeans. Past protectors didn’t have this issue.
As for alignment it looks perfect.
I’ve taken off my case a few times and no issues with the camera lens protector. I suppose if your case has issues, that’s what the individual lens protector style is for.
@@GillTechGroup yeah that is exactly why the Spigen protector is not so good, because its like a lint trap but the others are to big which causing the other problems of not sticking to the display in the outer areas. I had a camera protector in the past on my IP 13 pro max and i liked it because kin dof similar problems, the three cameras are a dust trap as well and with the protector no dust can come between the cameras.
A brand named “TOTEM” does this even better with Corning HD glass
Do the lens protectors affect the image or video quality, as it's been 2 weeks since the video came out; can you give me a detailed review of the lens protectors themselves. Looking forward to a response.
When the flash is on for either a photo or a video. I feel like it washes out the image. It’s definitely noticeable.
I wonder if the individual lens protectors solves this issue.
Otherwise I haven’t noticed any decrease in image quality.
I’ll see if I can figure out the best way to do a video to show this.
@@GillTechGroup Thanks for the response. Looking forward to a video regarding the same.
Damn bro you made this so difficult for yourself. Open room, remove screen sticker fresh from box and add the protector instantly. Why you removed it then let it sit to catch dust is beyond me
Yeah! Less than ideal. In the past I’ve put it on in the bathroom while running the shower on hot, so the steam helps knocks the dust down.
Would’ve been a lot harder to record there. It was wild though that there was dust inside the box already, maybe from the paper packaging?!
Got any tricks for me?
I removed the sticker fresh from the box on my 15 pro Max and applied the spigen screen protector right away and still managed to get dust underneath.
Did you not watch the video? As soon as he removed the sticker, dust kept getting on the screen.
it will get no matter what, I too got some and now they can be seen but whatever @@stamatispelekanos650
Bro, just lift up the screen protector slightly with your fingernail and use the dust removal sticker. You can easily get the piece of hair out by doing that.
I use to be in bathroom and let a hot shower build some steam to keep air dustfree.
Thats easy use the adhesive tape while tilting the screen using ur finger then slide the adhesive tape under the tempered glass and target that dust. Thank me later
what case are you using in the video?
It's a Smartish Gripmonk. It's the best rated case from Wirecutter's reviews, and I actually like it a lot. You can pick one up here amzn.to/404suw6 #ad
where do you get them?
I snagged mine off Amazon. Here’s a link: amzn.to/46oGe72 #ad
They also have an Apple Watch Ultra/Ultra 2 protector that I picked up, and made a separate video of. Here’s a link to the protector for the Ultra amzn.to/462rLOo
I installed it on my iPhone 15 Pro Max, and it doesn't fit. Maybe, the back ordered AGL06874 will fit. The AGL06872 definitely does not!
That’s weird! I just checked my box, and it says AGL06872.
What doesn’t fit on yours?
I had a iPhone 14 Pro with the same model screen protector, and it worked great. When I put this one on and removed the bubbles, it didn't align properly with the curvature of the rounded edges at the top and bottom of the iPhone screen. I guess if I had a case with thick bezels, I wouldn't notice it. It would be interesting to order the new model AGL06874, and see if there are any differences. @@GillTechGroup
Get it cleaned up real deep like😂
It’s come 2?
Yup, I got two in my package.
This screen protector is garbage.
people are so extra trust me its not hard to do and you dont need to wsh hands and be extra