HTS 2 Step Fireballs ALL MOTOR B18B NO VTEC MAKES ALMOST 180 WHP
HTML-код
- Опубликовано: 24 авг 2024
- Check out my website
www.huntertune...
Become A Patreon
/ huntertuned
Follow me on social media
HunterTuned RUclips Facebook Group
/ huntertunedyoutube
Instagram : / huntertuned1
Snapchat : HunterTuned
Email : HunterTuned@gmail.com
discovered that the noise was the bearing in the alternator.
That’s what I was thinking lol
Hey a b20z stock block with stock b16 head around what timing should be good on high cam trying to get idea ty
Where are you located at
@@pilotohernandez1569 28 deg
@@pilotohernandez1569 stock p30 jdm map hondata has good conservative timing, highlight whole vtec map column 1 through 8 remove 2 degrees.. 6000rpm to redline no more than 28 degree till dyno or street tune with knock ears
A 180hp Ls ?? Thats fucking Awesome !!!!!
Thats Canadian. Once you convert it, it amounts to 120hp.
@@journeyquest1he's in Wisconsin, that's not Canadian lol
I'm in the process of swapping a semi built ls atm. This video was awesome to see and makes me excited to see my progress.
This shines some light on my build
I have a similar setup,but built head with crower 404's and stock block! If he gets some Crower 404's and dual springs with titanium retainers he will have 185Hp+
I'm currently in the process of rebuilding my b18 and wanted to know what pistons you used?
@@Young_Blueberry_ Stock PHK pistons
titanium will melt stocks ok
@@ekelo ?
I have a fully Rebuilt b18a1,stock(fully ported/polished)head with crower 402s,stock block🤙🏼
Ever since the pandemic potential of b18b1 and b20b non VTEC build has cost mofo the p8r head to rise in price. Videos like this and info is great. Started mines way before this video, but it started getting expensive. I'm not done yet but I should see 200+ soon. Finally got my p8r head. Currently on e85 193/151tq
Love your videos man go back and watch old ones all the time
Had similar setup with itr piston and crower cams pulled hard,it's a different animal with out vtec instant power. I like how u show the 2 step with HTS,I run s300 on my turbo b20v. Keep it tuned up
Great content again, keep em coming. That motor just wants a VTEC head now!
Pretty sweet results with hts 💪
6:22 that rattle is 100% either the timing belt cover or the tensioner going out, I remove the timing cover on all my b series builds and just clean it with soap and water every time I wash the car
The big flat line up top is the ls head running out of flow ported head this thing would of made 200 I bet
What a little beast. Good job hunter. 👊💪
I watch this video everyday.. I can’t wait to run mines on a dyno
I doubt u still watching it today lol
I kinda like the HTS I got a car to run a 10.93 @126 on it at 19psi.
love the video keep it up I wanna see it at the track to see how she run getting motivated to make my b20b all motor non vtec
Yeah buddy moe powa baby!
It is the first time I heard of a 160 Hp Ls. I am very interested in the details and have one for replicating.
you can get 200 on a ls and
You should order yourself a $4 roll of desoldering wick. MUCH easier than a sucker. Probably gets more solder too.
I’ve tried the wick and didn’t have good luck when i tried it like 10 years ago I’ve had best luck with the sucker
@@HunterTuned Solder sucker works too. When you use the soldering wick, you have to use flux too. And the iron should be 750-800*F. Apply the flux to the solder spots on the board, lay down the wick, press the iron to the wick and it sucks it all up pretty easy.
Flux is key when soldering anything. The solder just jumps into the metal when it's on there.
@@HunterTuned I like the suckers better, but sometimes the wick is the more practical. It all depends.
The yihua soldering soldering station with sucker is the best thing to happen since sliced bread. Can get a whole board sucked in 10 minutes first try everytime. Parts are cheap and available.
@@HunterTuned hunter
I love❤😎 that ls b18b non vtec
I like how the wheel torque is same as the power it make's 180.1 flb 📈‼ lots of low end pull low rpm pulling power 👍🏾🥳
Hows says 🤔 Hondas dont make TQ lol 😁🤣 and that high ctr 11.1 compression pistons work and breathing nicely for n/a setup
Can you teach me how to tune my mustache? Where you can have it on and take it off? Lol
My question is, what should the wideband be reading while 2 stepping? I know what afrs for everything else. Don't think I've ever gotten an answer to this.
Great advice in the later part of the vid, keep it up mehn
Better header would make a huge difference
To me it looks like when you let off the throttle it went 8.0 which would be do to WOT fueling then the air flow being snapped shut and getting a large dose of fuel with no air. No?
Correct because the o2 sensor runs on real time
HTS the new version of chipping ecu? I have the classic chipped p28 and mine has 2 step I just never heard of HTS but heard of Neptune and chrome
I got a stock gsr same header and intake shoots a 5 foot flame on limiter and two step sounds like an ak tuned on hts I got lots of videos to prove it you use it on the old school chip the same way just better software the only thing I had problems with was boost cut but working sometimes in my buddys turbo d I tuned about 75 cars on it and I love it the pops and bang are like no other
You can use hts on any chipped ecu
@@HunterTuned so it’s like software for chipping ? Also on a side note I had a question :) I know you have seen a lot of weird stuff on Hondas and I was wondering if you ever had an issue of when you push the gas or rev the car it comes down all the way to like 100 right before shutting off and then surging back to 850? Does that sound like a vacuum leak or where would you start? Tps?
@@carnstar watch some of my recent videos I show this and how to fix the idle with the throttle stop screw on the bottom of the throttle cable actuator
180 Canadian WHP is more like 120 American WHP.
Pretty good decent power great content
this got me hyped to swap my ls into my crx
How well does that clear coat come off if you have to make changes to the board later on?
Hunter how much fuel enrichment do you usually add when doing ignition cut on 2 step?
Great job 👍🏻
enjoy your videos boss ! Keep up your hard work ❕
Can u do remote tuning? I need a tune.
can you chip a obd2 p75 ecu cuz thats what i have
Does it still has the stock cat in it? I've heard that 2 Step can break ceramic cats.
It will just hollow it out
No
"silly shit" - Hunter
awesome videos brother
Using a desoldering pump is my biggest pet peeve
I’m in Wisconsin and looking to have my D16z6 rebuild to 3-400 HP how can I get ahold of you to get done I have a 95 ex coupe D16z6
I also have a Vtech motor
Who do you get that much hp outta the motor what all is done to it
I’m new to these cars , i just got a 96’
Anyone know what’s ODII ? It marks on and making me fail smog . Can anyone help ?
How much compression is in it wtf lol . That’s really impressive .
Sup brother long time! Got a couple questions if you have the time homie!
What oil/sparkplugs you running?
I have a 1992 Acura Integra 1.8l its a B18A1 but I just wanted to know.. do I have to buy HONDATA? or can i just chip it? PLZ I am follower and I really wanted to gather everything I need to go over and for you to be my tuner.. I live in Texas but I got mad respect for you on your job skills...help me out bro!!! i will be adding turbo.. i have the setup already.. idk if temp will care.. due to me living in south Texas
Chip a po6 obd1 ecu get a obd1 dizzy too and all set
That's why u are where u stand. Be a follower and not a leader lol
I was hoping you would take it for it drive lol
Awesome
Hey Hunter, on a different topic, when boosting an NA motor, does the IAC valve need to be plumbed into the intercooler piping or can I just put an small filter off it.
I think u mentioned this on the Miata build that it’d be a boost leak ?
Idle air control is never installed in the intercooler pipe intake air temp is.
It only needs to bypass the throttle butterfly
What ecu are you using and tune
Stock bore?
My car currently runs 5w-30 would you recommend 10w-30? I’ve been looking on the forums and people run both.. im just not sure what to run.
10w-30 is better
Can i get a p28 for autonatic
Post mount is upside down
What if i get this map.. 😂
This is my goal for my integra
Lol that civic having high compression and only have almost 180 its rough lol my zero turn just about have that 😅 lol
3rd from the UK
I'm trying to locate a good tuner in the Chattanooga Tennessee area any suggestions ? LS VTEC on hondata
Jason waters is down that way
Thank you Hunter I'll check him out
Hey man I'd really like to know what piston that was running ctr? Maybe sweet tune epic power for a b18b
21:58
P8r head huh?
Dog pile chicken smile 🤣😂