Mark, I've watched many of your videos but this has been one of your best. I'm 72 years young and have been sign making and hand lettering signs for the past 40 years and woodworking for almost 55 years and this is some of the best advise I have seen. I purchased my CNC machine after I retired (lol) at the age of 60 from my full time job. Since I can't hold onto a brush any longer I'm making signs with the CNC. I've even misspelled words on signs and people have never even noticed it for 5+ yrs. As you said "NEVER point out your mistakes". Thank you for all that you do!! You've made learning to use Vcarve Pro so much easier.
Beginner CNC, these things are just good practices, that reduce errors, reduce scrap, and improve safety. These are just a few of the things that I did while working in CNC shop s, and a few of the things I required of all of my shop personnel when I had worked my way up to senior management running the shop floor. 1) Bring a notebook EVERY day, take detailed, organized notes on what you did, how, when, with what materials, what work holding method, what tooling and tech data (rpm/sfm, fpt/fpr,/ipm, doc, stepover, %of dia. engagement,), and detailed notes on results, good, bad, and what you're doing differently next time. 2) PROOFREAD YOUR ENTIRE PROGRAM, AND visualize all movements, paying particular attention to rapid moves. 3) Dry run, single block, and/or no tool/no workpiece, on prove out initial run of program. 4) USE EASILY UNDERSTOOD MAN-READABLES at the top of the program and before every operation, with accurate descriptions of the tool used, the operation (s) perfor offset(s)/coordinates used, critical dimensions/features created or affected in that operation. 5) LOOK at the cutter, the chips produced, the surface finished produced, LISTEN to the sound of every tool, in each cut, because these things can tell us an incredible array of very valuable information, we may greatly benefit from on the current part or project, or on an upcoming part or project.
“Perfection is subjective” That really stood out to me. My OCD causes me to over-complicate and question parts of my projects. Thanks for the insights!
I came to except that I’m never going to have it perfect in my eyes but as long as the person that I’m giving it to thanks that is perfect I am happy and so far no one’s complained
It's all a crawl, walk, run deal when starting out in this hobby/business. Mistakes will be made, use scrap wood or MDF or plywood for a test run. I did that when I did my first commission right after I bought my machine and then I went right into using oak for the projects. Most people think that you are the subject matter expert and will defer to your judgement. Thanks for the great video Mark and keep up the great work.
This was fantastic advice Mark. The not pointing out your mistakes thing really spoke to me! The pursuit of "perfection" is a thing I have struggled with myself in not just my cnc projects. My inner self always beats me up and only picks on the weaknesses, not the strengths of what I'm doing. Real good advice mate.
Hi Mark, just discovered this video and even as a person who has been doing CNC for a few years, what you say in the video applies to us all. Keep up the good work and thank you for sharing your wealth of knowledge and experience. It truly deserves high praise.
“Perfection is paralysis” - Dan Pena This quote changed my life. I had issues with taking perfection too far, which either caused my projects to stall or I would not even attempt them if I didn’t have all the ‘right’ tools. To your point I would only see the flaws, while others saw the overall result. One I heard that quote, I began to see what others saw and have since become far more productive.
I have been woodworking for years. Getting ready to buy my first CNC machine. You are spot on, and even experienced woodworkers may need the reminder from time to time. We all have to walk before we can run
I was watching a few videos before this on x2 speed and when this one came on I thought that youtube reverted back to normal speed. Great advice! Thank you!
Mark, your channel is the best thing on the web for CNCers of all skill levels, especially those of us beginning. Clear, concise, knowledgeable, encouraging good advice. Keep up the great work! I've learned more from your videos than all the others I've watched (many, many hours) combined. Thank you sir!
As someone who is sitting in front of a cnc machine who can’t get the thing working this is a nice video. It feels like every time I solve a problem there’s another waiting for me. You follow instructions and then your firmware software machine does something completely different
Reach out to your machine manufacturer's tech support folks. That's their job. If you have a generic CNC router with no manufacturer tech support, do a Google search for a support community for your machine. There are a number of support forums and Facebook groups dedicated to everything from an imported 3018 CNC on up to the high-dollar industrial units with 6 digit price tags. Those people know your machine best, because they use them.
Discouraged here after having the machine for just a week. Going to find as many videos as possible from the very start to no limit. I just started watching your videos and I love them!! I follow another great channel as well.
Everyone has been exactly where you are right now. Everyone. Slow down, take your time, and learn the control software. Try to find tutorials that are specific to your machine if possible. Remember - it isn't a race. If I can do this, you can do this.
Hi Mark. Thank you for some very good advice. I am just starting out in CNC but took up woodworking with hand tools three years ago when i retired. I discovered and embraced each one of your five points along the way and as a result have made some amazing things including a cot for our first grandchild. Its an amazing thing when you let go of the things you feel are right but are actually holding you back. So thanks again for the reinforcement. Love your videos.
"Take it easy on yourself; you are your own worst critic", is so true in so many areas of our lives. This isn't just good advice, it's profound wisdom.
Thank you very much, Dave. I don't know how profound it is, but it does reduce the stress level immensely. While we do need to look at our work with a critical eye (that's the only way we'll grow and improve our skills,) we need to stop being so critical that we end up trashing our work - literally OR verbally.
WOW, This is a great video. I just want to say that I have had a major life mental shift and a lot of the things that you say does apply to almost everything in life. Mindset is so very important and I am so happy to see someone be aware and share that mindset is your most powerful tool/asset in the shop! Thanks once again Mark!
Thank you very much, Johnny! It's too easy for me to get caught up in whatever mindset I'm in on any given day. I needed this for me as much as anything else.
I'm a few weeks into my CNC journey and very much appreciate this video. I was on the right track and I'll take it to heart... and make one further suggestion to #1 - it should apply to all woodworking, hobbies and life in general. We are all always too hard on ourselves when others only see the good. Many thanks once again!
I never thought I would listen to a CNC video And need to mention you've completely changed my way of thinking towards my work. your words speak volumes you have a hidden talent. I'm really enjoying your videos especially as a beginnner at 59 .You're making it much easier to understand what to expect what's needed to achieve your goals and to succeed. Thank you
I love your videos. I am barely one half year into CNC machines in wood working and I absolutely agree with every one of your points. Thank you for creating such informative videos. I continue to learn so much from you.
This video is spot on. I've had a Shapeoko 3 XL for 10 months. Get familiar w/ the machine, bits and whatever software you are using. I've had a lot of frustration and good luck. A lot of things worked and just when i thought I knew what I was doing I screwed up several projects. I moved back to my lathe for awhile and epoxy work. I finally decided I've spent way too much money on this to not get its full potential. I moved from Carbide 3 Create after a couple months to VCarve Desktop. Learned it enough just to get me by but realized I was denying myself the real potential of this awesome software (3D). I had look at some of Mark's videos when I first got VCarve earlier in the year but I still didn't have full command of this software until now. I have been studying all of Mark's videos in depth. I have learned so much more about this software and finally feel confident with it. It is so powerful. In my opinion, Mark's tutorials are the best on web for this software hands down. Don't give up. The CNC will do exactly what you tell it to do right or wrong!!
Thank you very much for your kind words, Gregg! I really do appreciate it. This whole CNC thing is just like anything else that's worth doing - you have to practice. That means making mistakes along the way, and learning from those mistakes.
I did autobody/collision repair for the last 45 years. And you #1 mistake was the same mistake I always made. I can hear my wife now, "Only you see that! No one else going to notice." And 99% of time, she was correct. Thank you for the great video. I'm just about ready to pull the trigger for a cnc machine. This was the perfect message at the perfect time for me to hear.
YOU JUST MADE ME CRY! And you also stopped me from throwing my CNC out the garage door! Thank you! I am guilty of all 5 of these things! Off to learn. Thank you again!
Mark I just finished watching this video of yours, and I couldn't agree more with your advice. I have found, the hard way, that you are absolutely correct with point number 5. I have started doing the most simple and what would seem stupid to a lot of people, things on my CNC. I have even made a simple square or circle and set depth of cuts just to see how deep it actually is when finished. I was surprised sometimes at what I learned. Experimenting with simple things like this that I can cut in scrap wood has taught me a lot in the past couple of months. But you are absolutely right, you have to learn the machine and the programming before expecting much out of either one of them at the start. Thanks for posting this, I think it is one of the best video's you have made. Thanks again and best to you. Jim
Thank you very much, Jim! The first thing I cut on my machine was a square with a circle inside it, then a triangle inside that circle. I then measured everything to make sure it was actually cutting a square, circle, and triangle. Then to see if everything was the right sizes and depths. Once I got everything calibrated and running correctly, I moved on to v-carving and profile cuts. I really don't know how many fence boards I chopped up, but it was a lot.
Number 5. Yes. I have had an Axiom AR8 for about 18 months. You are right. It did from the beginning do exactly what it was told to do. Right down to chewing up spoil boards and snapping cutters on clamps. I found that it did not respond to profanity. I’m 67. The bloke I bought the machine from (BG Precision Melbourne) is 32. I mean what would he know:). The pathway to happiness he said is twofold. Baby steps and meticulous adherence to process. ( and your excellent videos and those of Vetric). As my father once said When all else fails, read the instructions”
great video. i feel that you are talking to me and not at me . i' m looking forward to watching your videos and learning as much as i can about cnc. just setting up my cnc in my shop. keep up the good work.
I absolutely love this video. The last point of not pointing out mistakes really fits so many aspects of life and many poeple don't know how to deal with a compliment. Thanks for another grate video.
The part where you said "you don't buy a piano one week with never playing a piano and book your first concert at Carnegie Hall the next" sealed the deal. Thank you! That was brilliant!
Excellent advice Mark. I needed to hear this. Your encouraging words have come just in the nick of time. Your videos have been more helpful to me than any of the software tutorials. I want to offer the same words of encouragement right back at you. You are a very good communicator, keep up the awesome work, you are a valuable asset to the CNC community.
Thank you very much for the kind words, Donald. I really do appreciate it. I'll be around for as long as I'm physically able to do this RUclips thing. I've got too long of a to-do list to even remotely contemplate stopping. By the way - use the Vectric tutorials, too! They're great!
Good work, Mark! Your coaching on point four (Comparing ones self to others or lamenting ones self for lack of experience or progress) reminds me of my music tutors ! ! "And Practice, there is no replacement for experience. You MUST get out there and do it"
Thanks for all the insights. I have found that there is something to learned from every project I do, I always like to go over each project when I'm finished and ask myself what can I do to make it better or what I shouldn't have done. This the only way to get to be a better craftsman no mater what tool you are using. I also tend to set the bar a little higher than what I am comfortable with, and learn from my mistakes. If you only do what is easy so you can get a perfect finished project you will never advance your skills.
I agree with you 100%. In this video, my point was that a person needs to learn to crawl before they can run. Yes, the only way to advance is to challenge what you already know and can already repeatably, predictably do. But when you don't even know what you don't know yet, setting too high of a bar is setting yourself up for failure. I think that does more damage than good. There's a profound difference between challenging yourself and sabotaging yourself. Thanks very much, Dean!
Thank you for your 5 amazing advices. I fully agreed with them, I am also new to cnc and almost just putting together a 1500mmx1500mm Outback V1 CNC router kit thats very much customised. I realize how much more I have to learn and just reminding myself that I will get better and more confident and just keep at it doing 1 step at a time so its not overwhelming. Thanks for sharing your wisdom with us.
Just found this video and have a 16x16 Shapeoko I purchased used. Thanks for the insights! I'm a 3d printer owner and shortly after getting into that, I figured I not only wanted to do "additive" work (3d printing), but "subtractive" work (CNC)! Thanks for the insights, as I can see these rules applying to pretty much any new hobby or undertaking. I really appreciate the advice and am anxious to get my new CNC into a place where it will be safe to use for the long term.
Thank You Mark, i am new to CNC (3018 Pro) and Loving the results that i am getting from my homemade test projects. i have been checking out your work and Tutorial videos, they are of great inspiration. i am learning new things everyday from wood type, cut style, bits and end's along with the whole Lingo. And these 5 Suggestions you posted are a Solid Foundation to my desire to learn, have fun and create something out of CNC, once again Thank You.
Thank you for this video, I alway's point others to my mistakes, that's what I have to learn not to do anymore. I'm making my own cnc machine right now and I have to learn a lot. Your advice is great. Thanks for sharing.
This is more than just a CNC video. It's a life lesson and can be used for pretty much anything someone is doing for the first time. Some really well thought out advice from a passionate craftsman. Anyone who is picking up a new hobby should watch this video.
"Just say thank you!" That is good advice. You're very repetitive, this is a good element when I am viewing how to videos. Can't wait to learn more from your 50+ year's of experience. Thank you for the video!
I’m a beginner CNCer, have had a laser for a year, but have been a graphic designer for nearly 16 years….this is spot on! I’m going to have to play this for myself every Monday morning because even the mist experienced lose sight and get discouraged at their everyday tasks. Btw, I literally LOLed at the font choice part. That was perfect!
Hi from Valencia (SPAIN). Thanks alot Mark for this big lesson on this video. I realized that all what you said can be applied in whatever situation in life, it is an extremely good reflexion, not only for CNC personal projects. I´ve just purchased a very small CNC machine 3018 to introduce myself in this amazing CNC world, and righ away I find you saying such things! I´m so glad to start this path having watched your inspiring viedos, they offer me a good perspective on how to attain my goals. ¡Muchísimas Gracias! Eres una inspiración.
As somebody just looking into CNC for the first time, these were not the type of mistakes i expected ... as a general designer and DIY hobbyist, these advices are probably applicable to ANY type of activity you desire to get into. Hence i really like the list (hence i logged on and liked/commented) !! ... and lastly i would like to stress to anyone reading this comment, that the NR.1 point is probably the most important if you are thinking of making anything yourself and do not want to discourage yourself. I have run into it myself numerous times, you see the things that went wrong because in your mind you have a picture of how things should have gone, your client often does not have a picture of the end result in their mind, so what they see is the only thing they can reference, and thus they won't see those mistakes. And lastly, having done DIY projects in various materials, part of the learning curve of making anything, is to learn how to hide/prevent the ugly bits... The most easy i can explain this is in leatherworking, obviously at some point you need to finish the stitching with a knot, where you decide to put that knot (in sight or in a seam) will determine how 'professional' the end result will look. Another thing would be whether you show or do not show the stitching, especially if you do all the things by hand. Stichting a bag from the inside and turning the bag insight out, will look a lot better than doing it the other way around, given you may not have the tools and/or skills and/or experience to do a consistent good looking stitch. I am going to venture and guess the same thing applies to CNC work, where it relates to 'where you start or end a tool to integrate with the work' (likely comparable with drilling a hole in a plank that needs to be viewable from both sides, well you will want to put a 'waste board' underneath it, or else the hole on the other side will tare out). Similarly i can image having different tools to be able to do the same thing, but each leaving a different finish or level of detail. F/e using a contour router or rotating a different tool over several passes, where the work is to thick for the contour router to do a full rounding of the edge leaving a bit straight; where as the rotating tool could have done a full 1/4 circle, now you know and see this 'mistake'. Somebody that just sees there work, doesn't know what your intentions where and thinks it is just as beautiful. So really, don't beat yourself up over it, but mostly see it as a personal learning experience. Next time you will know what to do nor not to do, or how this 'mistake' now is actually the desired outcome on another project.
I think your hitting a topic that needed to be said. I am very new to this game. Hoping to eek out a little retirement funding. I enjoy working along with your videos. as I learn the program. I don't have a machine yet, I'm looking for a beginner machine. I already have a customer lined up for some very simple campground signs. Wish me luck. Thank you for all your hard work in producing the video's.
Your #1 suggestion is my biggest problem. Other people have told me the same thing. I concentrate my attention on every flaw and it drives me crazy. I'm 68 and still need to learn a lot of stuff. You have been a great help. Is there a pill or something that will change me? I no there isn't. My goal is to make quality projects that I am proud of. I am just so doggone picky. I will always be a work in progress but am having a great time doing it. Thanks again, you are a talented man and very inspirational. Keep up the good work!!!
Thank you very much, Dan! There are pills you can take, but in my experience, they just seem to make things worse - rarely better. We're always going to be harder on ourselves that we are on anyone else - I really think it's part of human nature. It's just learning what you can control and what you can't. I don't know that anyone will ever become an expert at that.
Mark YOU ARE ABSOLUTELY CORRECT MOST IMPORT is how to use the Software that you use to generate the G Code. I built the GarageWorx CNC machine and it is a super machine. I built my first CNC machine using MDF that was a learning experience and what it can or can not do. But, using the software such as Fusion 360 or Vetric software is what you need to master in order to think and feel how your machine will work with these different software.
Especially grateful for the advice on accepting complements graciously. I sometimes do exactly what you said not to do. Thanks for all the advice and all the vids!
William Frederick I built my CNC plasma / router about a year and a half ago, just doing a conversion to router during this shut down, your video's have been very informative, thru this journey I have been guilty of all of the above, thanks for opening my eyes to the big picture !
Hey Mark, I just watched this video and I have to say thank you. I just recently bought an X-carve CNC and just finished assembling it today. I haven't even made my first cut but, your video was very informative. Great advice!!!!!!!!!!!!!
I know nothing about CNC router or lathe, i've never used one. We do have cutting machines at work which use X Y and Z, and I can use that, but it's not a router, just a flat profile cutter. I realised very quickly that I have a huge interest in the inner workings and how it moves, how people create on it. All I know is I want to build one. I want to use it. I want to make things. I fell upon this video and it will remain in my favourites as purely great advice. Thank you for taking the time and sharing!
Thank you very much, Craig! I too caught the CNC bug early and wanted to build one from the first day I saw one in action. Before you spend the first penny, take a look at my friend Dave Gatton's home page, and read his advice to folks who are thinking about building/buying/getting a CNC router. No matter what brand you decide to go with, who you get a kit or plans from, there are some important things to consider BEFORE you jump into the pool. Dave lays those things out very well, and it's great food for thought. www.davegatton.com/
Truth. I've made it no secret that if it weren't for Dave, I wouldn't have gotten into CNC at all. I never doubted that I could build the structure, I'm just not an electronics guy. That part always got to me. With his help and tutelage, I was able to get my CNCs up and running just fine. He does make a lot of seriously good points in his article, though. I encourage everyone even remotely thinking about getting into CNC to read it and take it to heart.
Great advice for starting out simple. I'm a machinist but my Home CNC MILL was new to me so I started off with paper box and a zip tie in the spindle to test setups. It's a learning curve for sure.
I never point out things I feel are mistakes, especially to my customers. If they ask about it I offer an explanation and a refund if it really bothers them. Almost everything I sell I label as rustic, so there should be minor flaws. Thanks Mark great advice.
My first mistake I did (and I never will do again!?) was planing an MDF spoilboard with a 25 mm spoilbord surfacing router, used within it limits... The amount of dust produced needed to be cleaned up everywhere. And everywhere means everywhere.
Thank you Mark. I know this is an older video however for me, being a Newbie to cnc, I am going to make your list as my first sign project. It will hang in the shop above my machine when it's up and running (ONEFINITY end of May and very excited) I am a bit worried about lack of knowledge and learning curve but also eager to learn it right. Thanks again..Bill
Fantastic points, really liked not comparing your work to others and not pointing out your mistakes. Had a fortune cookie one time that read “experience is what you get when you don’t get what you want”. I can relate to that all too well! Thanks for sharing.
Reminds me of my first leather wallet sold... The customer kept saying he love it and is perfect but for me was awfull piece of work 😂😂😂🤦♂️ thanks sir great video 😍💪
Good advice. I always pointed out my mistakes. Its like im afraid someone else will see it and think I dont know it is there. But you are completely right. I will never again point out my little imperfections. Thanks for the tip
I think we all do it. It's almost like we think we're being dishonest if we don't. It wasn't until a friend asked me if her opinion wasn't good enough that I had to re-think things a bit. Thanks for watching!
Excellent video, I have been CNCing for over a year now and I too have fallen into the cycle of doing a project more than once, when the first cut was more than acceptable.
Thanks for sharing your thoughts, Mark. There’s some pretty solid advice here. It really brings me back to when I started. I scratch built my first CNC router from plywood back in 2011. Oh man, I bit off more than I could chew several times. Your point about building experience is exactly what it takes. Just gotta keep at it, screw up, learn something, and move on.
Absolutely, Bernie. Experience will come with practice - it just takes time and persistence. Then again, I've heard it said that experience is what you get when you don't get what you wanted.
I so agree with your video! Thanks for making this video. It's just you get excited to get a machine and start dreaming of all the cool stuff to make. It's best to start slow and learn! It's fun to enjoy the process forsure! Thank you
Thank you for this video. Your #1 tip really hit home with me. We are our own worst enemy. Had never thought about the fact that by not accepting a compliment graciously, you are negating the other person' opinion!
Thanks for your perspective Mark. This applies to all areas of life. I have known that I am far too critical of my work for years. The fact that pointing out flaws after being complimented is insulting is so important to remember. I always feel like it is arrogance to accept a compliment when I was am not happy with my work. The key, for me anyway, is allowing myself to see some imperfections and still be happy with my work. I hung a sign in my workshop a few years ago to remind myself of that. it says "Focus on Excellence, NOT Perfection." It is a reminder to me that excellence is achievable, perfection: rarely....if ever.
Thank you very much, Torrey. There is a lot of wisdom in those words; "Focus on Excellence, NOT Perfection." I truly believe that perfection is a subjective concept that isn't actually achievable, because no two people will have the same definition of it. All we can do is work hard to do the best job we're capable of. While that's easy for me to say, it's one of the hardest things I've ever had to learn and do.
What a life lesson awnswered, thanks you Was going to jump in with a photo carvin ive just converted Think ill just do a fue passes, see how the bits cut with different feed and speed rates at different depths
Mark, thank you for this advice. I’m about to start building my own CNC machine and this has been extremely helpful. I’m currently enrolled in a creative technology program at Berry College and have had several people ask me for prototyping freelance work. I’m also interested in starting my own business with my machine. I will revisit this video as I undoubtedly struggle to improve and accomplish my goals. Thanks again for the encouragement.
Thank you, Lewis. Just remember that it's not a race. You WILL get there if you want to, and are willing to put in the hours of practice, making mistakes, identifying the problems, and rectifying them. You got this!
Wow, thanks for you elaborate video. As a beginning CNC'er (build my own machine) i watch your videos one by one. Thanks Mark! Hope you keep making these awesome videos!
Wise words indeed Mark. Have been in the Hobby 2 years now, built my own machine from Hobby CNC plans, must say its been quite a ride so far. At the beginning not knowing anything about CNC machining, but have always been a fan of learning. Getting the machine to do what its supposed to do was a trip, along with learning Mach3 & Vectric Desktop, this old brain was pushed to its limits at times. My motto is Murphy rules if you don't take care. All the best Mark.
Thank you, David! I built my first CNC from plans too, and it was indeed a wild ride. But you know what? I still act like a 5-year-old when I fire it up and it does what I want it to do. Between you and me, I wish that Murphy guy would get a hobby and stay out of my shop. Fat chance of that, but a guy can wish, can't he?
I should have watched this video before starting CNC machining. All these mistakes felt so familiar, and now I'm aware of them. Thank you for this amazing list!
Thanks Mark, a good video for a beginner. It's like life, you learn something new everyday. I always asked my kids what did you learn at school today, they would say nothing, so I would say you didn't learn anything today that you didn't know yesterday.
Wow....lessons for life.....I particularly liked your emphasis on not pointing out mistakes. I tend to do that and didn't realize the negative impact it might have on others. Thanks!
Great video, your absolutely right on all counts. I try and solve all my design issues on my own and only ask support for help when all else fails. Trial and error allows you to learn the software and when you do need help you understand what support is talking about.
Hello Mark, to travel a thousand kilometers you have to take the first step, and I think that enjoying the process makes someone follow or not. Being able to find a mistake and repair it is comforting. Thanks again for refreshing these concepts, regards
Honestly, I am about to retire from my job and I hope to spend some time at the CNC to try to get a project going so that my youngest son has job possibilities. I think he does a great job with his channel and I think it's great to get out of the purely technical realm to get into the concept of the activity. I would like to thank you from Spain for your dedication and wonderful work. All the best.
As someone who has worked with CNC type equipment for over 30 years this is all good advice for a beginner and in some cases the experienced user as well.
Your rock man. your last advice was so deep taking into my critical brain I can't even tell you. I am 95% laser engraver and 5% CNC , all you talk applies to almost every crafts person. Thank you again and you just removed a very heavy sack of my back that I almost carry after every job.
Honestly , every word you said in the video is what i feel right now , always learning far to be perfect and thanking people and helping the ones behind me , great content !!! Love it
![Down Bits (Down Cut) And CNC Routers [What You Didn't Know] - Garrett Fromme](http://i.ytimg.com/vi/tykj6Nn-ysM/mqdefault.jpg)
Mark, I've watched many of your videos but this has been one of your best. I'm 72 years young and have been sign making and hand lettering signs for the past 40 years and woodworking for almost 55 years and this is some of the best advise I have seen. I purchased my CNC machine after I retired (lol) at the age of 60 from my full time job. Since I can't hold onto a brush any longer I'm making signs with the CNC. I've even misspelled words on signs and people have never even noticed it for 5+ yrs. As you said "NEVER point out your mistakes". Thank you for all that you do!! You've made learning to use Vcarve Pro so much easier.
came for the technical advice, stayed for the good vibes! I tip my hat sir!
Thank you! I hope it helped!
Beginner CNC, these things are just good practices, that reduce errors, reduce scrap, and improve safety. These are just a few of the things that I did while working in CNC shop s, and a few of the things I required of all of my shop personnel when I had worked my way up to senior management running the shop floor.
1) Bring a notebook EVERY day, take detailed, organized notes on what you did, how, when, with what materials, what work holding method, what tooling and tech data (rpm/sfm, fpt/fpr,/ipm, doc, stepover, %of dia. engagement,), and detailed notes on results, good, bad, and what you're doing differently next time.
2) PROOFREAD YOUR ENTIRE PROGRAM, AND visualize all movements, paying particular attention to rapid moves.
3) Dry run, single block, and/or no tool/no workpiece, on prove out initial run of program.
4) USE EASILY UNDERSTOOD MAN-READABLES at the top of the program and before every operation, with accurate descriptions of the tool used, the operation (s) perfor offset(s)/coordinates used, critical dimensions/features created or affected in that operation.
5) LOOK at the cutter, the chips produced, the surface finished produced, LISTEN to the sound of every tool, in each cut, because these things can tell us an incredible array of very valuable information, we may greatly benefit from on the current part or project, or on an upcoming part or project.
Nice points! Ever see a >250k line program? We work with those regularly, would be impossible to proofread. (Lots of simulations :p)
“Perfection is subjective”
That really stood out to me.
My OCD causes me to over-complicate and question parts of my projects.
Thanks for the insights!
Thank you very much! It took me a long time to figure that out. I still have trouble with it at times.
I over engineer due to my OCD and one phrase I will never accept (due to OCD) is the phrase "design it to be good enough". :/
I came to except that I’m never going to have it perfect in my eyes but as long as the person that I’m giving it to thanks that is perfect I am happy and so far no one’s complained
It's all a crawl, walk, run deal when starting out in this hobby/business. Mistakes will be made, use scrap wood or MDF or plywood for a test run. I did that when I did my first commission right after I bought my machine and then I went right into using oak for the projects. Most people think that you are the subject matter expert and will defer to your judgement.
Thanks for the great video Mark and keep up the great work.
Spot on advise. An old timer once told me that the CNC machine was like a good soldier, that if ordered to, would march off a cliff.
This was fantastic advice Mark. The not pointing out your mistakes thing really spoke to me! The pursuit of "perfection" is a thing I have struggled with myself in not just my cnc projects. My inner self always beats me up and only picks on the weaknesses, not the strengths of what I'm doing. Real good advice mate.
I am bad about doing excaly what he said. I will try to do better and that goes with all my creations not just CNC stuff.
Hi Mark, just discovered this video and even as a person who has been doing CNC for a few years, what you say in the video applies to us all. Keep up the good work and thank you for sharing your wealth of knowledge and experience. It truly deserves high praise.
I am a beginner and you put me in check and also eased my mine. Thank you for this list. I am my own worst enemy in the begining journey.Thank you!!!
Dear Mark, When I heard this, I felt as if you understood my problems and advised me. Your advice has opened my eyes. Thank you.
“Perfection is paralysis” - Dan Pena
This quote changed my life. I had issues with taking perfection too far, which either caused my projects to stall or I would not even attempt them if I didn’t have all the ‘right’ tools. To your point I would only see the flaws, while others saw the overall result. One I heard that quote, I began to see what others saw and have since become far more productive.
I have been woodworking for years. Getting ready to buy my first CNC machine. You are spot on, and even experienced woodworkers may need the reminder from time to time. We all have to walk before we can run
I was watching a few videos before this on x2 speed and when this one came on I thought that youtube reverted back to normal speed. Great advice! Thank you!
Mark, your channel is the best thing on the web for CNCers of all skill levels, especially those of us beginning. Clear, concise, knowledgeable, encouraging good advice. Keep up the great work! I've learned more from your videos than all the others I've watched (many, many hours) combined. Thank you sir!
As someone who is sitting in front of a cnc machine who can’t get the thing working this is a nice video. It feels like every time I solve a problem there’s another waiting for me. You follow instructions and then your firmware software machine does something completely different
Reach out to your machine manufacturer's tech support folks. That's their job. If you have a generic CNC router with no manufacturer tech support, do a Google search for a support community for your machine. There are a number of support forums and Facebook groups dedicated to everything from an imported 3018 CNC on up to the high-dollar industrial units with 6 digit price tags. Those people know your machine best, because they use them.
Discouraged here after having the machine for just a week. Going to find as many videos as possible from the very start to no limit. I just started watching your videos and I love them!! I follow another great channel as well.
Everyone has been exactly where you are right now. Everyone. Slow down, take your time, and learn the control software. Try to find tutorials that are specific to your machine if possible. Remember - it isn't a race. If I can do this, you can do this.
Thank you for the pep talk.
I am 59yr and still have trouble with motivation because I can't wait to learn something,
I just need to be patient.
Hi Mark.
Thank you for some very good advice.
I am just starting out in CNC but took up woodworking with hand tools three years ago when i retired.
I discovered and embraced each one of your five points along the way and as a result have made some amazing things including a cot for our first grandchild.
Its an amazing thing when you let go of the things you feel are right but are actually holding you back.
So thanks again for the reinforcement.
Love your videos.
"Take it easy on yourself; you are your own worst critic", is so true in so many areas of our lives. This isn't just good advice, it's profound wisdom.
Thank you very much, Dave. I don't know how profound it is, but it does reduce the stress level immensely. While we do need to look at our work with a critical eye (that's the only way we'll grow and improve our skills,) we need to stop being so critical that we end up trashing our work - literally OR verbally.
Thanks, (Uncle Mark) really needed this, I've progressed more than I thought I would in 6 months and still beating myself up.
WOW, This is a great video. I just want to say that I have had a major life mental shift and a lot of the things that you say does apply to almost everything in life. Mindset is so very important and I am so happy to see someone be aware and share that mindset is your most powerful tool/asset in the shop! Thanks once again Mark!
Thank you very much, Johnny! It's too easy for me to get caught up in whatever mindset I'm in on any given day. I needed this for me as much as anything else.
I'm a few weeks into my CNC journey and very much appreciate this video. I was on the right track and I'll take it to heart... and make one further suggestion to #1 - it should apply to all woodworking, hobbies and life in general. We are all always too hard on ourselves when others only see the good. Many thanks once again!
I never thought I would listen to a CNC video And need to mention you've completely changed my way of thinking towards my work. your words speak volumes you have a hidden talent. I'm really enjoying your videos especially as a beginnner at 59 .You're making it much easier to understand what to expect what's needed to achieve your goals and to succeed. Thank you
I love your videos. I am barely one half year into CNC machines in wood working and I absolutely agree with every one of your points. Thank you for creating such informative videos. I continue to learn so much from you.
Thank you very much for your kind words! I do appreciate it.
Thank you for point 1. That is my biggest problem but you made me think of it in a different way. I’ll be working on this thru out my CNC journey.
This video is spot on. I've had a Shapeoko 3 XL for 10 months. Get familiar w/ the machine, bits and whatever software you are using. I've had a lot of frustration and good luck. A lot of things worked and just when i thought I knew what I was doing I screwed up several projects. I moved back to my lathe for awhile and epoxy work. I finally decided I've spent way too much money on this to not get its full potential. I moved from Carbide 3 Create after a couple months to VCarve Desktop. Learned it enough just to get me by but realized I was denying myself the real potential of this awesome software (3D). I had look at some of Mark's videos when I first got VCarve earlier in the year but I still didn't have full command of this software until now. I have been studying all of Mark's videos in depth. I have learned so much more about this software and finally feel confident with it. It is so powerful. In my opinion, Mark's tutorials are the best on web for this software hands down. Don't give up. The CNC will do exactly what you tell it to do right or wrong!!
Thank you very much for your kind words, Gregg! I really do appreciate it. This whole CNC thing is just like anything else that's worth doing - you have to practice. That means making mistakes along the way, and learning from those mistakes.
Got to tell Mark, your not just a great CNC expert but also a great phycologist, love your stuff, well done.
I did autobody/collision repair for the last 45 years. And you #1 mistake was the same mistake I always made. I can hear my wife now, "Only you see that! No one else going to notice." And 99% of time, she was correct. Thank you for the great video. I'm just about ready to pull the trigger for a cnc machine. This was the perfect message at the perfect time for me to hear.
This video has to be titled “5 golden rules on how to start any project” thank you very much for the video!
Thank you very much!
YOU JUST MADE ME CRY! And you also stopped me from throwing my CNC out the garage door! Thank you! I am guilty of all 5 of these things! Off to learn. Thank you again!
Mark I just finished watching this video of yours, and I couldn't agree more with your advice. I have found, the hard way, that you are absolutely correct with point number 5. I have started doing the most simple and what would seem stupid to a lot of people, things on my CNC. I have even made a simple square or circle and set depth of cuts just to see how deep it actually is when finished. I was surprised sometimes at what I learned. Experimenting with simple things like this that I can cut in scrap wood has taught me a lot in the past couple of months. But you are absolutely right, you have to learn the machine and the programming before expecting much out of either one of them at the start. Thanks for posting this, I think it is one of the best video's you have made. Thanks again and best to you.
Jim
Thank you very much, Jim! The first thing I cut on my machine was a square with a circle inside it, then a triangle inside that circle. I then measured everything to make sure it was actually cutting a square, circle, and triangle. Then to see if everything was the right sizes and depths. Once I got everything calibrated and running correctly, I moved on to v-carving and profile cuts. I really don't know how many fence boards I chopped up, but it was a lot.
Number 5. Yes. I have had an Axiom AR8 for about 18 months. You are right. It did from the beginning do exactly what it was told to do. Right down to chewing up spoil boards and snapping cutters on clamps. I found that it did not respond to profanity. I’m 67. The bloke I bought the machine from (BG Precision Melbourne) is 32. I mean what would he know:). The pathway to happiness he said is twofold. Baby steps and meticulous adherence to process. ( and your excellent videos and those of Vetric). As my father once said When all else fails, read the instructions”
great video. i feel that you are talking to me and not at me . i' m looking forward to watching your videos and learning as much as i can about cnc.
just setting up my cnc in my shop. keep up the good work.
This such excellent advice! I am going to send this to my daughter who is beginning to do water color paintings. The advice is universal.
I absolutely love this video. The last point of not pointing out mistakes really fits so many aspects of life and many poeple don't know how to deal with a compliment. Thanks for another grate video.
Thank you very much, Kurt! I really appreciate it!
The part where you said "you don't buy a piano one week with never playing a piano and book your first concert at Carnegie Hall the next" sealed the deal. Thank you! That was brilliant!
Excellent advice Mark. I needed to hear this. Your encouraging words have come just in the nick of time. Your videos have been more helpful to me than any of the software tutorials. I want to offer the same words of encouragement right back at you. You are a very good communicator, keep up the awesome work, you are a valuable asset to the CNC community.
Thank you very much for the kind words, Donald. I really do appreciate it. I'll be around for as long as I'm physically able to do this RUclips thing. I've got too long of a to-do list to even remotely contemplate stopping. By the way - use the Vectric tutorials, too! They're great!
Good work, Mark! Your coaching on point four (Comparing ones self to others or lamenting ones self for lack of experience or progress) reminds me of my music tutors ! ! "And Practice, there is no replacement for experience. You MUST get out there and do it"
I am sooo guilty of not being able to just say "thank you". My wife points it out to me all of the time. Thank you for your sound advice!
Thanks for all the insights. I have found that there is something to learned from every project I do, I always like to go over each project when I'm finished and ask myself what can I do to make it better or what I shouldn't have done. This the only way to get to be a better craftsman no mater what tool you are using. I also tend to set the bar a little higher than what I am comfortable with, and learn from my mistakes. If you only do what is easy so you can get a perfect finished project you will never advance your skills.
I agree with you 100%. In this video, my point was that a person needs to learn to crawl before they can run. Yes, the only way to advance is to challenge what you already know and can already repeatably, predictably do. But when you don't even know what you don't know yet, setting too high of a bar is setting yourself up for failure. I think that does more damage than good. There's a profound difference between challenging yourself and sabotaging yourself. Thanks very much, Dean!
Another great video. Your last one hit home. I'm guilty of this and have been trying to get better at it.
Thank you for your 5 amazing advices. I fully agreed with them, I am also new to cnc and almost just putting together a 1500mmx1500mm Outback V1 CNC router kit thats very much customised. I realize how much more I have to learn and just reminding myself that I will get better and more confident and just keep at it doing 1 step at a time so its not overwhelming. Thanks for sharing your wisdom with us.
I am as an absolute CNC-beginner from east germany I am absolutely...with you ! Regards... :)
Just found this video and have a 16x16 Shapeoko I purchased used. Thanks for the insights! I'm a 3d printer owner and shortly after getting into that, I figured I not only wanted to do "additive" work (3d printing), but "subtractive" work (CNC)! Thanks for the insights, as I can see these rules applying to pretty much any new hobby or undertaking. I really appreciate the advice and am anxious to get my new CNC into a place where it will be safe to use for the long term.
Thank You Mark, i am new to CNC (3018 Pro) and Loving the results that i am getting from my homemade test projects. i have been checking out your work and Tutorial videos, they are of great inspiration. i am learning new things everyday from wood type, cut style, bits and end's along with the whole Lingo. And these 5 Suggestions you posted are a Solid Foundation to my desire to learn, have fun and create something out of CNC, once again Thank You.
Thank you for this video, I alway's point others to my mistakes, that's what I have to learn not to do anymore. I'm making my own cnc machine right now and I have to learn a lot. Your advice is great. Thanks for sharing.
Thank you! These aren't just for CNC -- they're for any maker, just about anything we build, make, or refine.
Thank you, Artie! I do appreciate it!
This is more than just a CNC video. It's a life lesson and can be used for pretty much anything someone is doing for the first time. Some really well thought out advice from a passionate craftsman. Anyone who is picking up a new hobby should watch this video.
"Just say thank you!" That is good advice.
You're very repetitive, this is a good element when I am viewing how to videos. Can't wait to learn more from your 50+ year's of experience. Thank you for the video!
I’m a beginner CNCer, have had a laser for a year, but have been a graphic designer for nearly 16 years….this is spot on! I’m going to have to play this for myself every Monday morning because even the mist experienced lose sight and get discouraged at their everyday tasks.
Btw, I literally LOLed at the font choice part. That was perfect!
Hi from Valencia (SPAIN). Thanks alot Mark for this big lesson on this video. I realized that all what you said can be applied in whatever situation in life, it is an extremely good reflexion, not only for CNC personal projects. I´ve just purchased a very small CNC machine 3018 to introduce myself in this amazing CNC world, and righ away I find you saying such things! I´m so glad to start this path having watched your inspiring viedos, they offer me a good perspective on how to attain my goals. ¡Muchísimas Gracias! Eres una inspiración.
As somebody just looking into CNC for the first time, these were not the type of mistakes i expected ... as a general designer and DIY hobbyist, these advices are probably applicable to ANY type of activity you desire to get into. Hence i really like the list (hence i logged on and liked/commented) !! ... and lastly i would like to stress to anyone reading this comment, that the NR.1 point is probably the most important if you are thinking of making anything yourself and do not want to discourage yourself. I have run into it myself numerous times, you see the things that went wrong because in your mind you have a picture of how things should have gone, your client often does not have a picture of the end result in their mind, so what they see is the only thing they can reference, and thus they won't see those mistakes. And lastly, having done DIY projects in various materials, part of the learning curve of making anything, is to learn how to hide/prevent the ugly bits...
The most easy i can explain this is in leatherworking, obviously at some point you need to finish the stitching with a knot, where you decide to put that knot (in sight or in a seam) will determine how 'professional' the end result will look. Another thing would be whether you show or do not show the stitching, especially if you do all the things by hand. Stichting a bag from the inside and turning the bag insight out, will look a lot better than doing it the other way around, given you may not have the tools and/or skills and/or experience to do a consistent good looking stitch.
I am going to venture and guess the same thing applies to CNC work, where it relates to 'where you start or end a tool to integrate with the work' (likely comparable with drilling a hole in a plank that needs to be viewable from both sides, well you will want to put a 'waste board' underneath it, or else the hole on the other side will tare out). Similarly i can image having different tools to be able to do the same thing, but each leaving a different finish or level of detail. F/e using a contour router or rotating a different tool over several passes, where the work is to thick for the contour router to do a full rounding of the edge leaving a bit straight; where as the rotating tool could have done a full 1/4 circle, now you know and see this 'mistake'. Somebody that just sees there work, doesn't know what your intentions where and thinks it is just as beautiful.
So really, don't beat yourself up over it, but mostly see it as a personal learning experience. Next time you will know what to do nor not to do, or how this 'mistake' now is actually the desired outcome on another project.
I think your hitting a topic that needed to be said. I am very new to this game. Hoping to eek out a little retirement funding. I enjoy working along with your videos. as I learn the program. I don't have a machine yet, I'm looking for a beginner machine. I already have a customer lined up for some very simple campground signs. Wish me luck. Thank you for all your hard work in producing the video's.
Most of what you are saying is an amazing lesson not just for CNC. I truly appreciated it. Thank you from Italy.
Your #1 suggestion is my biggest problem. Other people have told me the same thing. I concentrate my attention on every flaw and it drives me crazy. I'm 68 and still need to learn a lot of stuff. You have been a great help. Is there a pill or something that will change me? I no there isn't. My goal is to make quality projects that I am proud of. I am just so doggone picky. I will always be a work in progress but am having a great time doing it. Thanks again, you are a talented man and very inspirational. Keep up the good work!!!
Thank you very much, Dan! There are pills you can take, but in my experience, they just seem to make things worse - rarely better. We're always going to be harder on ourselves that we are on anyone else - I really think it's part of human nature. It's just learning what you can control and what you can't. I don't know that anyone will ever become an expert at that.
As someone who is just getting into the CNC world, this video was very refreshing! Thanks a lot
Mark YOU ARE ABSOLUTELY CORRECT MOST IMPORT is how to use the Software that you use to generate the G Code. I built the GarageWorx CNC machine and it is a super machine. I built my first CNC machine using MDF that was a learning experience and what it can or can not do. But, using the software such as Fusion 360 or Vetric software is what you need to master in order to think and feel how your machine will work with these different software.
Especially grateful for the advice on accepting complements graciously. I sometimes do exactly what you said not to do. Thanks for all the advice and all the vids!
William Frederick
I built my CNC plasma / router about a year and a half ago, just doing a conversion to router during this shut down, your video's have been very informative, thru this journey I have been guilty of all of the above, thanks for opening my eyes to the big picture !
Hey Mark, I just watched this video and I have to say thank you. I just recently bought an X-carve CNC and just finished assembling it today. I haven't even made my first cut but, your video was very informative. Great advice!!!!!!!!!!!!!
I know nothing about CNC router or lathe, i've never used one. We do have cutting machines at work which use X Y and Z, and I can use that, but it's not a router, just a flat profile cutter. I realised very quickly that I have a huge interest in the inner workings and how it moves, how people create on it. All I know is I want to build one. I want to use it. I want to make things.
I fell upon this video and it will remain in my favourites as purely great advice. Thank you for taking the time and sharing!
Thank you very much, Craig! I too caught the CNC bug early and wanted to build one from the first day I saw one in action. Before you spend the first penny, take a look at my friend Dave Gatton's home page, and read his advice to folks who are thinking about building/buying/getting a CNC router. No matter what brand you decide to go with, who you get a kit or plans from, there are some important things to consider BEFORE you jump into the pool. Dave lays those things out very well, and it's great food for thought. www.davegatton.com/
Oddly I have checked out Dave Gatton's video's before, he's come a long way since I first found his channel and it continues to be an inspiration :-)
Truth. I've made it no secret that if it weren't for Dave, I wouldn't have gotten into CNC at all. I never doubted that I could build the structure, I'm just not an electronics guy. That part always got to me. With his help and tutelage, I was able to get my CNCs up and running just fine. He does make a lot of seriously good points in his article, though. I encourage everyone even remotely thinking about getting into CNC to read it and take it to heart.
Great advice for starting out simple. I'm a machinist but my Home CNC MILL was new to me so I started off with paper box and a zip tie in the spindle to test setups. It's a learning curve for sure.
Thank you, Dan! It's all about learning the tool and how to use it.
I never point out things I feel are mistakes, especially to my customers. If they ask about it I offer an explanation and a refund if it really bothers them. Almost everything I sell I label as rustic, so there should be minor flaws. Thanks Mark great advice.
Thanks Mark…. From one of your “Beginner” Subscribers.
You’re the Pinnacle mate. Love you’re teaching style and you’re Encouragement 🙏
My first mistake I did (and I never will do again!?) was planing an MDF spoilboard with a 25 mm spoilbord surfacing router, used within it limits... The amount of dust produced needed to be cleaned up everywhere. And everywhere means everywhere.
Thank you Mark. I know this is an older video however for me, being a Newbie to cnc, I am going to make your list as my first sign project. It will hang in the shop above my machine when it's up and running (ONEFINITY end of May and very excited) I am a bit worried about lack of knowledge and learning curve but also eager to learn it right. Thanks again..Bill
Fantastic points, really liked not comparing your work to others and not pointing out your mistakes. Had a fortune cookie one time that read “experience is what you get when you don’t get what you want”. I can relate to that all too well! Thanks for sharing.
Reminds me of my first leather wallet sold... The customer kept saying he love it and is perfect but for me was awfull piece of work 😂😂😂🤦♂️ thanks sir great video 😍💪
Good advice. I always pointed out my mistakes. Its like im afraid someone else will see it and think I dont know it is there. But you are completely right.
I will never again point out my little imperfections. Thanks for the tip
I think we all do it. It's almost like we think we're being dishonest if we don't. It wasn't until a friend asked me if her opinion wasn't good enough that I had to re-think things a bit. Thanks for watching!
I started work in CNC a week ago. There’s a LOT of mistakes I made.
Thank you for the video
Mark, very good advise, need a sign on my wall with you comments.
Excellent video, I have been CNCing for over a year now and I too have fallen into the cycle of doing a project more than once, when the first cut was more than acceptable.
Thank you very much, Andrew! I think we all do it.
Thanks for sharing your thoughts, Mark. There’s some pretty solid advice here. It really brings me back to when I started. I scratch built my first CNC router from plywood back in 2011. Oh man, I bit off more than I could chew several times. Your point about building experience is exactly what it takes. Just gotta keep at it, screw up, learn something, and move on.
Absolutely, Bernie. Experience will come with practice - it just takes time and persistence. Then again, I've heard it said that experience is what you get when you don't get what you wanted.
Thanks Mark. I am exploring the future purchase of a CMC
I so agree with your video! Thanks for making this video. It's just you get excited to get a machine and start dreaming of all the cool stuff to make. It's best to start slow and learn! It's fun to enjoy the process forsure! Thank you
Thank you, Cheryl! Just keep in mind that it IS a process, and you should do fine.
Thank you for this video. Your #1 tip really hit home with me. We are our own worst enemy. Had never thought about the fact that by not accepting a compliment graciously, you are negating the other person' opinion!
Thanks for your perspective Mark. This applies to all areas of life. I have known that I am far too critical of my work for years. The fact that pointing out flaws after being complimented is insulting is so important to remember. I always feel like it is arrogance to accept a compliment when I was am not happy with my work. The key, for me anyway, is allowing myself to see some imperfections and still be happy with my work. I hung a sign in my workshop a few years ago to remind myself of that. it says "Focus on Excellence, NOT Perfection." It is a reminder to me that excellence is achievable, perfection: rarely....if ever.
Thank you very much, Torrey. There is a lot of wisdom in those words; "Focus on Excellence, NOT Perfection." I truly believe that perfection is a subjective concept that isn't actually achievable, because no two people will have the same definition of it. All we can do is work hard to do the best job we're capable of. While that's easy for me to say, it's one of the hardest things I've ever had to learn and do.
What a life lesson awnswered, thanks you
Was going to jump in with a photo carvin ive just converted
Think ill just do a fue passes, see how the bits cut with different feed and speed rates at different depths
Mark, thank you for this advice. I’m about to start building my own CNC machine and this has been extremely helpful. I’m currently enrolled in a creative technology program at Berry College and have had several people ask me for prototyping freelance work. I’m also interested in starting my own business with my machine. I will revisit this video as I undoubtedly struggle to improve and accomplish my goals. Thanks again for the encouragement.
Thank you, Lewis. Just remember that it's not a race. You WILL get there if you want to, and are willing to put in the hours of practice, making mistakes, identifying the problems, and rectifying them. You got this!
any update? How's it going?
Wow, thanks for you elaborate video. As a beginning CNC'er (build my own machine) i watch your videos one by one. Thanks Mark! Hope you keep making these awesome videos!
I’m very new to CNC and needed to hear this. Thanks.
Wise words indeed Mark. Have been in the Hobby 2 years now, built my own machine from Hobby CNC plans, must say its been quite a ride so far. At the beginning not knowing anything about CNC machining, but have always been a fan of learning.
Getting the machine to do what its supposed to do was a trip, along with learning Mach3 & Vectric Desktop, this old brain was pushed to its limits at times. My motto is Murphy rules if you don't take care.
All the best Mark.
Thank you, David! I built my first CNC from plans too, and it was indeed a wild ride. But you know what? I still act like a 5-year-old when I fire it up and it does what I want it to do. Between you and me, I wish that Murphy guy would get a hobby and stay out of my shop. Fat chance of that, but a guy can wish, can't he?
For the first 4, I was all «I don’t do that, I’m good»
For number one... not so much..
Good advice!
Thank you Gunnar! I'm still pretty bad with #1 myself, but I am getting better about it.
I should have watched this video before starting CNC machining. All these mistakes felt so familiar, and now I'm aware of them. Thank you for this amazing list!
Thank you very much! We all do, or have done, one or more of them. I think it's just part of the process of learning our craft.
Thanks Mark, a good video for a beginner. It's like life, you learn something new everyday. I always asked my kids what did you learn at school today, they would say nothing, so I would say you didn't learn anything today that you didn't know yesterday.
Thank you very much, Gerry! I do appreciate it! All we can do is our best, then try to get better.
Wow....lessons for life.....I particularly liked your emphasis on not pointing out mistakes. I tend to do that and didn't realize the negative impact it might have on others. Thanks!
Thank you Mark. I already recognized myself in focusing on small errors that others actually do not see. Fortunately this happened within my family.
It happens to all of us. I know it all too well. Thank you for watching!
Great video, your absolutely right on all counts. I try and solve all my design issues on my own and only ask support for help when all else fails. Trial and error allows you to learn the software and when you do need help you understand what support is talking about.
Hello Mark, to travel a thousand kilometers you have to take the first step, and I think that enjoying the process makes someone follow or not. Being able to find a mistake and repair it is comforting. Thanks again for refreshing these concepts, regards
Thank you very much. It's all a part of the learning process. We just have to remember that we ARE learning.
Honestly, I am about to retire from my job and I hope to spend some time at the CNC to try to get a project going so that my youngest son has job possibilities. I think he does a great job with his channel and I think it's great to get out of the purely technical realm to get into the concept of the activity. I would like to thank you from Spain for your dedication and wonderful work. All the best.
Excellent advice for any endeavor, not just CNC beginners.
As someone who has worked with CNC type equipment for over 30 years this is all good advice for a beginner and in some cases the experienced user as well.
Thank you very much, Scott! I do appreciate it!
This is good advice for anyone who makes builds or creates anything.
Your rock man. your last advice was so deep taking into my critical brain I can't even tell you. I am 95% laser engraver and 5% CNC , all you talk applies to almost every crafts person. Thank you again and you just removed a very heavy sack of my back that I almost carry after every job.
Honestly , every word you said in the video is what i feel right now , always learning far to be perfect and thanking people and helping the ones behind me , great content !!! Love it
Hi Mark, thanks for the one sided talk i loved it i needed it, now back to fixing my problems.
Very positive and enlightening. First time I have looked at a CNC channel. Thank you.
Great tips that most of us don't even think of or realize. Thanks for your help.
Thank you very much, John! I do appreciate it.
As a novice in the CNC world, I appreciate your advice so very much.
Thank you so very much.
Thank you very much, Sir! I do appreciate it.
Thank you. I just started out with a 3018 and I really need to know all I can.. This really helps!