How to Check DYSON V11 Vacuum Cleaner Motor with Multimeter?
HTML-код
- Опубликовано: 5 фев 2025
- How to repair/fix Dyson V11 vacuum cleaner. How to check Dyson V11 vacuum cleaner motor with a multimeter.dyson repair. Dyson fix. In this video, we will guide you through the process of checking the motor of Dyson V11 vacuum cleaner using a multimeter. We will show you how to properly connect a multimeter and measure resistance to make sure the motor is working correctly. This step-by-step tutorial will help you troubleshoot motor problems and make sure your Dyson V11 vacuum cleaner is running smoothly. The Dyson V11 vacuum cleaner motor I show in the video works smoothly. You can measure the motor of your own vacuum cleaner, using the measurements you will see in the video as reference. If you found the video useful, you can like it and write any questions you have in the comments section.
Aliexpress Venlap Official Store
bit.ly/3lGOLjE
Aliexpress VENLAB VM-200M Multimeter sales link
bit.ly/3xt81DL
Aliexpress 2$ discount code
3TB5OID0CWKM
venlab multimeter review video:
• Unlocking the Secrets ...
My other repair videos.
bit.ly/3k8NzRH
My DIY videos.
bit.ly/3j4aOgr
You can contact me via e-mail elektronikatolyem@gmail.com
Do not forget to "like" the video if you like it. You can subscribe by clicking to not to miss new videos / @electronic7979
#repair
#fix
#circuitboardrepair
#electronicscreators
#elektronikkarttamiri
#elektroniktamir
#electronicrepair
#tamir
#electronics
#dyson
#dysonrepair
#dysonfix
#vacuumcleaner
#vacuumcleanerfix
#motor
Aliexpress Venlap Official Store
bit.ly/3lGOLjE
Aliexpress VENLAB VM-200M Multimeter sales link
bit.ly/3xt81DL
Aliexpress 2$ discount code
3TB5OID0CWKM
venlab multimeter review video:
ruclips.net/video/FiJ85YdUPd4/видео.html
My other repair videos.
bit.ly/3k8NzRH
My DIY videos.
bit.ly/3j4aOgr
Nice meter and soldering 👍
Thank you for your interest and valuable comment, my friend.
Hello thank you for the videos I also check my pcb but I have about 1.6 m ohm on the pcb without motor and it goes up is this normal? Thank you
It is normal for a value as high as 1.6 megaohms to appear when there is no motor.
@electronic7979 Okay thank you I ask because you have 1m ohm
Nice
thank you
Привет, где купить плату управления ?
Hi! where can I buy a control board of Dyson V10?
You can find it on sites like ebay or aliexpress, you need to do some research. Or you can find it at an authorized service.
my friend , how can i fix v11 that works only at top speed?
Hello. If your Dyson V11 vacuum cleaner only works at the highest speed, it might indicate a problem with the speed control circuit or its components.
1. Potentiometer or Sensor Issue in the Trigger
The speed adjustment is usually done through a potentiometer or sensor connected to the trigger mechanism. If this part is faulty, speed control cannot be achieved.
Solution: Check the potentiometer or sensor in the trigger with a multimeter. Replace it if it is defective.
2. Speed Control Circuit Fault
The Dyson V11 uses an electronic circuit to control the motor speed. Components like the MOSFET, transistor, or PWM (Pulse Width Modulation) control circuit may have failed.
Solution: Inspect the speed control circuit, identify any damaged components, and replace them.
3. Main Board Problem
A short circuit, burned resistor, or capacitor on the main board's control circuit can disrupt speed control.
Solution: Carefully examine the main board and replace any suspicious components. If you notice visible burn marks on the circuit, prioritize inspecting that component.
4. Software Error
Some Dyson V11 models use a microcontroller for speed control. A software or firmware issue could cause the device to operate at only one speed.
Solution: Try resetting the device to factory settings. Refer to the instructions in Dyson's user manual for guidance. If necessary, seek support from an authorized service center.
İhtiyacı olana güzel bilgiler eline sağlık.
İlginiz ve değerli yorumunuz için teşekkür ederim.
Hola, mi dayson v12 funciona pero antes hay que apretar entre 5 y 10 veces el boton de encendido.
Pensaba que era problema de suciedad pero la he limpiado y soplado totalmente. Sera de la parte electronica pero no se si piede ser lo que miestras en el video.¿ Alguna ayuda para coger un camino?
Muchísimas gracias por el video
Your problem may be caused by the button inside the on/off switch. You can check its strength by measuring the button with a multimeter.
What did you use to remove the coating on the terminals
I cleaned the coating with isopropyl alcohol. I removed the solder on the motor ends using a vacuum desoldering iron.
How to confirm the motor winding is not burnt or open circuit?
You can understand it by measuring it with a multimeter.
Merhabalar .. bizde dyson v11 absolute v14 var, calisiyordu kullanmak istedigimizde düğmeye basinca motor çalışmmiyor sanki baslayacak gibi oluyor dönmeden birakiyor. Batarya 100% , ne olabilir?
Motorun çalışıp hemen durması birkaç farklı sebepten kaynaklanıyor olabilir. İşte bazı olasılıklar:
1. Motor Koruma Sistemi: Dyson süpürgelerde motoru korumak için bir koruma devresi bulunur. Bu devre, aşırı akım veya motorun fazla zorlanması durumunda devreye girip motoru durdurur. Eğer devre bir sorun algılarsa motor daha başlamadan durabilir.
2. Batarya ve Güç Dağıtımı: Bataryanız dolu gibi görünse de, motora yeterli akım veya voltajı sağlayamayabilir. Bu da motorun çalışmasını engelleyebilir. Özellikle batarya bağlantılarında gevşeklik, ya da bataryanın iç direncinin artması bu sorunu tetikleyebilir.
3. Motor ya da Elektronik Kart Arızası: Elektronik kartta veya motorun içinde bir kısa devre ya da arıza varsa, motor anlık olarak çalışıp hemen durabilir. Bu, arızalı bir bileşenle ilgili olabilir.
Son olarak süpürgenin filtresinden veya borularında tıkanıklıkta olabilir.
Umarım bu bilgiler sorununuzu çözmenize yardımcı olur! Eğer başka bir sorunuz varsa, seve sev
e yanıtlarım.
Hola, el motor de mi aspiradora hace un zumbido pero no gira, que puede ser?. Gracias. Muy buen video
Thank you for liking my video. The problem is most likely due to the motor driver MOSFETs on the circuit board.
Hello, do you know what should I check with voltimeter if vacuum is working but not image on screen?
Check that the cables and sockets to the display module are intact. If there is a contact problem, the display may not receive power. Check that small components in the display circuit, such as fuses or resistors, are burnt or shorted. Check the correctness of the values of these components by measuring them with a multimeter.
Check the voltage inputs to the display module. Measure the voltage coming into the display module by setting the multimeter to DC voltage mode. Make sure that the required voltage is supplied according to the manufacturer's specifications.
Visually inspect the display circuit and main circuit board. Watch for physical signs of damage, such as burn marks, cracked components, or cold solder.
Hi Tell me, is there a forced engine shutdown, mine has started to work unstably?
I do not know exactly. There may be a solder crack on the electronic circuit board.
On my vacuum V6 accidentally some water got in the motor and now it does not start. I noticed that in the back of the motor is a LED that it is flashing 5 times and if I push the button some kind of small clicks can be heard.
Water in your Dyson V6 vacuum cleaner may have caused short circuits or damage to the motor and electronic components. LED warning lights, especially on Dyson vacuum cleaners, indicate certain types of faults. A rear LED flashing 5 times usually indicates a problem with the motor or battery.
The following problems can occur when the motor is exposed to water:
1. Motor short circuit: If water has seeped into the motor, motor components may short circuit.
2. Control board damage: Electronic control boards may be damaged by water. Motor driver mosfets may have failed.
3. Battery failure: If water has come into contact with the battery, the battery may also be damaged.
4. Trigger mechanism: A clicking sound when the button is pressed can indicate that the motor is being forced to start but the electrical connection is not correct.
What to do:
Wait to dry: If water has only gotten superficially into the vacuum cleaner, waiting for it to dry completely can sometimes solve the problem. You can open the vacuum cleaner and clean the areas that have been in contact with the water.
Мой пылесос как то работает странно,я думаю мотор надо менять,ни где не могу найти информацию. Он работает но с прирывистым шумом при этом не всасывает. Что это может быть,хотелось бы знать точнее,так как я сегодня его разбирала полностью,продула всё от пыли но он всё ровно шумит при включение странно
There may be the following problems in a vacuum cleaner that makes strange noises and has low suction power:
1- When the bearings in the motor of the vacuum cleaner wear out, it can make loud or strange sounds. In this case, the motor or bearings may need to be replaced.
2- A decrease in suction power may be caused by a clogged hose or filters. Check that all filters are clean and the hose is completely open.
3- If the motor used in the vacuum cleaner is a brushed motor; When the carbon brushes of the motor wear out, it may make noise and the motor efficiency may decrease.
4- There is a fan or impeller inside the vacuum cleaner that helps the motor's traction power. If this part is broken or damaged, it can both make noise and reduce suction power.
5- If there are small cracks or sealing problems in the body or hose of Dyson vacuum cleaners, this can also make noise and reduce suction power.
I recommend that you check what I have written.
Thanks for the video and the infos. I have a Dyson V10 and it seems like it has an issue with the motor or the circuit board. The problem is it only works in the max suction settings and when i try to use it in the firts two settings it just starts and stops in an instant. What dou you think the problem could be? Could the soldering joints be a part of this problem (i say this because the left part of the soldering joints seems a little bit yellowy) or should i renew the solder joints? Thanks in advance.
Merhaba. öncelikle devre kartı üzerindeki tüm lehimleri tazelemenizi tavsiye ederim. Bunun dışında devre kartı üzerindeki mosfetleri ve dirençleri kontrol edebilirsiniz.
Here are a few possible reasons why the engine may be vibrating.
1. Clogging: A blockage that blocks the air flow can cause the engine to run unevenly. Check the filters, hoses, and vacuum cleaner heads for blockages.
2. Filter Problem: A dirty or incorrectly installed filter can also cause the engine to vibrate. Clean the filter or replace it if necessary.
3. Engine Problem: There may be a problem with the internal parts of the engine or the fan blades.
4. Foreign Object in the Pipe or Head: A foreign object stuck in the vacuum cleaner's pipe or head can also cause vibration. Remove these parts and check for foreign objects.
Aynı sorun bende de var 😮
Hi, How can I make sure motor or board witch is broken?
You can check the motor and the materials on the circuit board by measuring them using a multimeter.
Dyson v10 can't work. Symptoms are as follows.
1. When connecting the charger, turn off after turning on 3 blue LEDs.
2. Remove the main body and battery and disassemble the battery. Press the battery switch and turn off 3 LEDs.
3. The battery's own voltage comes out well. Press the switch on the battery and the P+P- voltage comes out for a while and then it doesn't come out.
May I know if it's a battery problem or a body problem?
Thanks for your comment! The symptoms you mentioned usually indicate that the battery may be faulty. If the 3 blue LEDs are on, it means that the battery is not accepting a charge or is faulty. The problems you are experiencing with the battery voltage values also indicate that the battery is not working. First of all, I would recommend replacing your battery. If the problem persists, then there may be a problem with the main body of the device. I hope this information helps!
How the Dyson detects the filter is chocked
A clogged filter will cause the motor to work harder to maintain suction power. Dyson vacuums monitor the load on the motor and if it detects that the motor is straining more than normal, it will assume there is a blockage, which could be a clogged filter. It can detect a filter blockage by calculating the current drawn by the motor.
Carpet & floor Rollers spin for 1 sec & stop in Eco mode v11 vaccum. Releasing the button & pressing it again does exactly the same. Whats this problem & where to check on the board. Can you make a detailed video about it & share.. thanks
Unfortunately, I have never encountered such a problem before.
Nice RUclips. Dyson V10 What if only one "boom" sound with full battery light on, but motor do not move ?
Hello. The motor or driver mosfets may be faulty.
@@electronic7979 Thx!
@@jamescheung6004Do you have any progress of fixing you motor? I have the same issue.
@@licysaab finally, I ve replaced it by new motor (Alibaba) and sell the old one at lower price. (I think expertise know how to fix it as many want it). Now, dyson v10 works fine up to now.
What if V11 is pulsing, where to check on the motor or pcb? Thanks
You should check the motor driver mosfets and microprocessor.
@electronic7979
do you have the part number for the driver mosfets/ replaceable mosfets that will work on it? Thx
добрый день. могли бы назвать маркировку микросхемы U12 .как она в миру зовётся?
Hello my friend.
Unfortunately, I have no knowledge about this integrated circuit. I couldn't find any database on the internet. What was wrong with the cleaner?
Amazing
thank you
Buenas se me lleno de agua el aspirador dayson v10 hemos cambiado batería y motor y sigue sin funcionar
The electronic circuit board has also failed.
Solder sucker hangi marka baya iyi çekti?
Merhaba cihazın ismi: xytronic 988d soldering and desoldering station
V11 motor tamirati yaparmisiniz ??
arıza neydi
Very useful video. Thanks a lot!
Thank you for your interest.
I need a way to contact you
We can contact you via my e-mail address elektronikatolyem@gmail.com.
elektronik kart arızalı nasıl bulurum şimdiden teşekkür
Merhaba. Elektronik devre kartını yetkili serviste bulabilirsin.
My Dyson V10 Short capacitor I changed but still not working
Motor driver mosfets may be faulty.
ممكن وسيله تواصل معك ارجوك
We can contact you via my e-mail address elektronikatolyem@gmail.com
Iletisime gecebilirmiyiz ??
elektronikatolyem@gmail.com mail adresinden iletişime geçebiliriz.
Muchas gracias
thank you for your interest
have you measured a faulty motor/motherboard? what are the values of a faulty motor?
A faulty motor. When you measure the motor by removing it from the circuit board, it usually shows an open circuit.
👍👋👋
thank you
Value less than zero ohms? Only superconductors have zero ohms. And less than zero I didn't even think was possible. And on top of that at room temperature... :)
Great observation! Actually, superconductivity and resistance below zero ohms are theoretically not possible at room temperature. The point I was trying to make in the video was a very low resistance value. Thanks for noticing, your comment helped me clarify!
👍
thank you
Pointless Video. Showed the motor removed and then replaced. Meter on the motor connections but no resistance values.
Hello. First of all, thank you for your comment. I think you didn't understand the video. The motor you see in the video works smoothly. I have shown the measurement values so that you can reference them on your own vacuum cleaner. subject of the video; Since the internal resistance of a good motor is low, it is normal for it to show zero ohms when measured with a multimeter.
Einfach nur sinnlose Zeitverschwendung.
Thank you for your feedback! My goal is to provide useful content that everyone will enjoy. What topics or formats would be more interesting to you? I can use this feedback to make future videos better.
TÜRKÇE dururken başka dil kullanmaya ne gerek var?
Malesef Türkçe içeriklere sponsor gelmiyor. Yakında Türkçe bir kanal açıp aynı içerikleri Türkçe olarak yayınlayacağım.