Peugeot 106 Front wheel bearing
HTML-код
- Опубликовано: 10 дек 2021
- In this video I change the front bearing on a Peugeot 106 Rallye. It should apply to all 106 and also Citroen Saxo I belive
Bliv medlem af denne kanal for at få adgang til fryns:
/ @seasidegarage 
Авто/Мото
Great video. You are one of very few you tubers who knows which bearing race to push on and when. So many other videos demonstrate how to damage a new bearing. Well done and thank you.
Thank you.... Thats a pretty important thing to do right, unless you really enjoy to change them... ;)
9:45 using the grinder is the last option I did it many times. Two mounting levers from your workbench and some nuts or peaces of something to put under to create a strong leverage are all you really need. I was always surprise how easy it went off.
Thank you for taking the time to make this video 😊
That strut looked surprisingly easy to handle and carry. A benefit of working on smaller cars, I guess.
yup... very light!
Great video again .you make it look so easy .
Editing all the cursing and desperate methods out helps.... ;)
I was on the MOT and tyhe bearing was not oke in one front wheel, but when I drive the car I do hear nothing strange, also not with taking a corner. Is then the bearing bad or is it a other sound.
Great video. Question: my 106 start to do a high pitch noise at speeds above 50km/h. Could it be the front wheel bearing? Cheers.
Mine axle bold in middel of wheel is quite vastened, and even a big pin do bent.
Excellent work, the front of the bearing often falls apart when you push the hub out, the whole process is always a fight, strangely satisfying to do however.
Those struts look like they were found on an archaeological dig! 😅
Thanks!
Haha yes... Our country is rough on cars.... The roads where white today, and it was not snow... it was salt... :O
@@SeasideGarage dude I sympathise ours are no field trip but I can imagine it’s even worse for you.
They weren’t beyond restoration however I’ve had to chip my way through similar in the past. Those circlips were in there though, jeez!
@@edh7492 Haha I think it took 30minuts to get them out! They where so so stuck... The eyes for the pliers snapped off instantly... ;)
Jeg stod lige og skulle bruge en video om skift af hjulleje på en 106... Hvem kan hjælpe? Seaside of course! 😃🙏
Does it matter which way the bearing goes in?
That car seems to have an appetite for bearings... :P
Yep.... hot hatch... +300.000km and a life with many "modders" have put a big strain on everything on this old gem...
Super god gennemgang af lejeskiftet og videoen slutter med, at du ikke monterer akselbolten, men hvilke Nm skal den spændes med? Mvh. Michael
Jeg kunne ikke lige huske NM så derfor tog jeg det ikke med.. Men stramt! ;)
Tak!
One step closer to rallying....
Next up will be the clutch cable! Its going to be a big improvement to have the clutch biting point above the carpet.... :P
you should have told people that some of the bearings only go in one way as it might of had abs so the magnet ring goes close to the abs sensor even tho yours didn't have abs
I never heard of abs rings being in the bearing?
On these cars the abs ring (if fitted) are located on the driveshaft. :)
@@SeasideGarage it might not be fitted to the cars you work on but it would be helpful to the people who just use the video as a referans i like your show keep up the good work
@@quinta3005 thanks :)
Kunne du tænke dig at skifte hjulleje på den igen? 😂😂
Er det gået igen ? To år var ikke længe..!
Den snerrer ihvertfald noget fra højre forhjul når jeg kører i den 😂 men okay, den har så oss været en tur på Padborg Park, kan godt være det var det den ikk ku tåle 🤣
@@MrSibby169 haha ja det kunne godt tænkes... Det er hård kost !
Håber at den køre godt ellers ! Den er savnet her !
@@SeasideGarageden kører hammer godt, har dog måtte skifte benzinpumpen på den da den døde i sommers 😅 men ellers kører den perfekt, og elsker det faktum at det er den eneste rallye med soltag 😂
@@MrSibby169 det er sgu fedt at høre ! Mega fed bil!