Just some led strips I found on Amazon they are 12v I wired them to the first battery for the hydraulics and added a switch on the power wite to turn them on and off
@domenickalonzo4679 it's a buddy of mines he is in Georgia he wants 18.5k it looks completely different it's cobalt blue and ls swapped hit him up on Facebook his name is Donnie Funk
Nice my first car was my oldsmobile 98 I drove it for a few months before juicing it I wouldnt really recommended having a lowrider for a daily drive but some how I did it. Knowing how to work on then yourself helps
Thanks look through all the videos that's why I make them so people can learn feel free to ask questions there is a good chance I have a video that will answer any question you have if not i can probably make one
Bro you do some good work I got a quick question I have the same setup but I'm new at this. can you show a video of how you stand the car up on three wheel motion in park...every time I try I can't get the front end in the air..🤔
I dont have anything around at the moment to make a video but all you need to do if its chained properly is lift the front end up then with the rear end all the way down lift what ever side you want to raise you should feel the chains get tension and hit the switch a few more times and the car should tip listen to the sound of your pumps so you know when you are fully locked up you will hear the pump boog down a little
I drilled a 4 inch hole in the sheet metal and used a tail light grommet for a semi I came across some that were solid and I cut a x in them so the cylinder could pass through unfortunately I dont remember where I got them because I was trying to get them again
How much is it for a 4pump set up , with all the main basics. Arms, balls , braces, slip yoke, charger and everything. I got a cutty that needs hydros bad. Do you have any recommendations?
@@thecadillacdanshow8658hey brotha. Gotta question. I tried finding that video you did on the trunk shocks on hulk. Do you still have that up?? Lmk appreciate ya.
Another awesome video Dan, super excited for you on building a new shop I recently did something similar and was able to save big $$$ by contacting my power company for old telephone poles they worked great for me, I like the trusses try rustoleum turbo cans to save time
@@thecadillacdanshow8658 Question. I have 2 stress cracks on each window side upper corner. On my cuttless. What should I do weld or just Bondo and touch up with paint? Thanks.👏🏼👍🏼🙏🏼
@thecadillacdanshow8658 thank you dan...I am.wamting to add another pump to my set up of 2 pump 6 batteries 4 dumps...researching on plumbing and wiring...cost of another pump and other
If you have any questions feel free to ask if I have a video I will send you a link or if I have time and parts I can throw a video together explaining
@thecadillacdanshow8658 Well I'm in Augusta Ga, I have a 92 Brougham I would like to get juiced. And there's no shops around here at all. Plus I like the fact it's just you working on the cars. I read you were booked for a few months. You don't see that around here and I would love to stand out.
Hey I really like your video. How can I get in touch with you? I wanted to ask you some questions regarding what you did. It’s pretty cool that you have that Oldsmobile.
@@thecadillacdanshow8658 I have a red set up fbss double pump 2 pump just need batteries and battery rack dough nut cups and spings I like your set up with the Cutlass emblem thats hard I'm in Augusta ga what's my price for installation
I got a question when welding the bridge did you just weld the bottom side of the bridge and not the top bcuz you could reach the top to weld. Also the guy who installed my switches cut the front spring while still compressed to release tension.
@thecadillacdanshow8658 thanks for the info my guy. I plan on putting a bridge on my cousins car and was wondering if welding one side on bcuz that's all I can get to would make me look bad. I watch all your vids and gonna build AArms and everything else the way you do it.
@@hosscaddy I would at least do the rear arches as a very minimal you are adding alot more weight then the frame was designed to hold think of holding a brick in your hand with your arm extended all the way out eventually it's going to get tired and drop
@@hosscaddy if you need some work done you can get up with maximino de Leon he is in Ohio. If you havnt already check out the channel gem city welding billy is also in Ohio
Yeah I want every set up to stand out. It's a terrible business move but for now I basically build cars for fun. I dont enjoy doing basic setups but I do need to get in the mindset of that's only what most people want to pay for. I have just been lucky to get cool customers that are open to adding changes
@@thecadillacdanshow8658 I wouldn't say it's a terrible business model, it's indeed what will keep you in business. If it's still fun for you to do, then you're on the right track. I've had a 83 coupe and a 90'd out 84 sedan on juice, just hard to find for a good deal now days. The ones I do find are too pretty to cut up. Nice work tho man, take care.
AWSOME JOB ,
THAT CUTTY HELLA GANGSTA NOW
👍🔥👍🔥👍
Thanks
@@thecadillacdanshow8658
YOU'RE WELCOME BRUH , KEEP THEM VIDEOS COMING
🔥🔥🔥
Great job. I had an 85 cutty back in the day to this day the smoothest car ive driven
What you did in this video is sic to death!!! I applaud you!! My question is what lights did you use to light up the trunk? Thanks in advance
Just some led strips I found on Amazon they are 12v I wired them to the first battery for the hydraulics and added a switch on the power wite to turn them on and off
I’m really digging your batt tiedowns lighting and accents. Super trick when you pop the trunk. Good job bro!
Thanks I wanted to do something different that I have never seen before it worked out good. The car is for sale and looking for a new owner
How much are you asking?
@domenickalonzo4679 it's a buddy of mines he is in Georgia he wants 18.5k it looks completely different it's cobalt blue and ls swapped hit him up on Facebook his name is Donnie Funk
I’ll consider it. Thnx 4the get back
Good job that car looks super nice
Thank you!
The Covers are Tight💪🏾💯
Donnie got a monster. 🥰 Awesome work, as usual bro.
Thanks
This gives me lots of inspiration to when ever i get my car, im 15 nd im trynna get a 86 cutty. Good work on the build, its gonna help me a lot💯
Nice my first car was my oldsmobile 98 I drove it for a few months before juicing it I wouldnt really recommended having a lowrider for a daily drive but some how I did it. Knowing how to work on then yourself helps
Clean clean clean work brother !!!!! Great video !!! Thanks again
Thank you
Pretty sick man reds my favorite color as well. Had an cutlass a long time ago on wires no juice but i felt like i was king riding in it
U did a good job
Thanks!
Oh yeah, Great WORK.😊
Car clean and the set up is clean. Great work
Thank you!
Favorite car cutlass I gotta build me another one I miss that car
Great job! Looks clean!
Thanks!
Sweet great set up
Super clean work as usual Dan… 💯
Thank you!
I would love to Have the knowledge to do this And admire your work !
Hopefully one day i could learn and educate myself Beautiful Car !!!
Thanks look through all the videos that's why I make them so people can learn feel free to ask questions there is a good chance I have a video that will answer any question you have if not i can probably make one
@@thecadillacdanshow8658 thank you Sm for the reply ! I want my kids to grow up and learn about cars specially lowriders 🙏
Outstanding setup!!!
Thank you!
Great job!!!
Thank you I am going to need to do a updated video on the car he has made a lot of improvements since it left
Cutty Dan The Man!!!! Never that Always Cadillac!!!!
Man that work look amazing.. do you work on subscribers cars ?
Nice work 👌
Thanks!
Maaaannnn that’s sweet! Well done sir!!
Thanks man it turned out sweet
This set up is clean
Thank you!
Bro you do some good work I got a quick question I have the same setup but I'm new at this. can you show a video of how you stand the car up on three wheel motion in park...every time I try I can't get the front end in the air..🤔
I dont have anything around at the moment to make a video but all you need to do if its chained properly is lift the front end up then with the rear end all the way down lift what ever side you want to raise you should feel the chains get tension and hit the switch a few more times and the car should tip listen to the sound of your pumps so you know when you are fully locked up you will hear the pump boog down a little
Here you go right around the 15 minute mark I three wheel this caprice with chains
ruclips.net/video/25jm8BD-r9o/видео.htmlsi=uxOb6DjksvyWbJc_
@thecadillacdanshow8658 thank bro ill try that
One more thing what size cylinders should I be using for the front I have 8" cylinders in the front 16" in the back?
That should be plenty this cutlass had 12s and caprice had 14s
That's looking good.
Thanks
Llac man is killing it…..
Thank you! I try
Man I need this on my 92 caprice
It can be done!
Thank you for the inspiration man I can’t wait to 3 wheel motion in the caprice 🛞🛞🛞
Beautiful work
Thank you!
That setup looks dope homie
Thank you!
NICE SETUP how much for a 3 pump set up in my 84 cadillac cope deville
Message me on Facebook and we can get some numbers up it all depends on what you want to get I'm in Alabama in case you didnt already know
Where did you get the caps for the hydraulic cylinders in the trunk?
What caps? The rubber grommets?
So would you be able to give a wire diagram on how you did your batteries to pumps
Nice work, what size cylinders did you use in the rear, also do you have a pic of how you reinforced the front pockets?
This one had 12s in the rear I will be having a video on doing the spring pockets
Nice!!!
Nice work man did U plate up the front arches and belly?
Not on this one I did do the spring pockets though
What size rear cylinder requires adjustable arms? The arches were the only stress points done? Nice work
I did the rear arches inside and out, a bridge and the front spring pockets 12s and up I do adjustable arms above 12s I do drop mounts
What ton springs did you go with in this? I just bought something similar with a 305, 2 pump , 6 battery and it rides super bad and bouncy.
3.5 ton in the front and 2 ton precuts in the rear
What’d you use to clean up the cylinder holes in the trunk? One side is blown out in my trunk from 3 wheeling with no bridge 😖
I drilled a 4 inch hole in the sheet metal and used a tail light grommet for a semi I came across some that were solid and I cut a x in them so the cylinder could pass through unfortunately I dont remember where I got them because I was trying to get them again
Dope Trunk
Thanks!
When you put in the bridge you didn’t have to cut anything out of the way?
I cut the spring pockets out of the way
Ok
Why not black tractor paint for the trusses?
What’s up bro , quick question do you Recommend installing an inline fuse to your 24v wire?
100% do
How much is it for a 4pump set up , with all the main basics. Arms, balls , braces, slip yoke, charger and everything. I got a cutty that needs hydros bad. Do you have any recommendations?
Where are you located?
@ Hilo Hawaii
There are some guys out there that build cars I don't remember any names off the top of my head but if I come across them I will send you their info
Looks Real Good Brutha
Thank you
@@thecadillacdanshow8658hey brotha. Gotta question. I tried finding that video you did on the trunk shocks on hulk. Do you still have that up?? Lmk appreciate ya.
Here you go
ruclips.net/video/By0-Agoiy2c/видео.html
What does that street charger do?
Charges you batterys while you drive
Hi Dan . Awesome work . By any chance do you do outside work ?
I do but I am booked up for the next few months
Another awesome video Dan, super excited for you on building a new shop I recently did something similar and was able to save big $$$ by contacting my power company for old telephone poles they worked great for me, I like the trusses try rustoleum turbo cans to save time
Yeah I may have to see about some old power polls that's a good idea
@@thecadillacdanshow8658 Question. I have 2 stress cracks on each window side upper corner. On my cuttless. What should I do weld or just Bondo and touch up with paint? Thanks.👏🏼👍🏼🙏🏼
@soulessm8015 I would weld it for sure those are some heavy doors and they tend to do that after a while
@@thecadillacdanshow8658 Another question.what about stress cracks.upper corner back near top of the car of the windows? Thanks. 👍🏼🙏🏼
Definitely have to weld those up is the car already juiced?
What ton coils u got in front n back
3.5 in the front and 2 ton pre cuts in the rear
Nice
Bad ass work dan where are u located
Montgomery al
What would you charge to do one
Builds start at 6k and go up depending on what you all want done
So do u have the 2 silonoids per pump
I usually do one solenoid per 2 battery's
@thecadillacdanshow8658 thank you dan...I am.wamting to add another pump to my set up of 2 pump 6 batteries 4 dumps...researching on plumbing and wiring...cost of another pump and other
I found alot of useful videos out there I learned alot from including your vids..
If you have any questions feel free to ask if I have a video I will send you a link or if I have time and parts I can throw a video together explaining
@@thecadillacdanshow8658 and do I need a 6 switch panel
Whats up Dan? Love the Videos. Please tell me you are located in Georgia
I'm not far from it I'm in Montgomery
@thecadillacdanshow8658 Well I'm in Augusta Ga, I have a 92 Brougham I would like to get juiced. And there's no shops around here at all. Plus I like the fact it's just you working on the cars. I read you were booked for a few months. You don't see that around here and I would love to stand out.
Message me on Facebook we can see about getting a game plan going
Hey I really like your video. How can I get in touch with you? I wanted to ask you some questions regarding what you did. It’s pretty cool that you have that Oldsmobile.
You can message me on here or on Facebook
How much to do my 86 ?
@martincortez9131 it all depends on how far you want to go builds start at 6k and go up from there
Hey Dan where are you located?
Alabama
How much would u charge to do my 84 Cutlass supreme
It all depends on what you all want done a basic lay and play setup starts at 7k
@@thecadillacdanshow8658 I have a red set up fbss double pump 2 pump just need batteries and battery rack dough nut cups and spings I like your set up with the Cutlass emblem thats hard I'm in Augusta ga what's my price for installation
Message me on Facebook and we can get a quote up
I got a question when welding the bridge did you just weld the bottom side of the bridge and not the top bcuz you could reach the top to weld. Also the guy who installed my switches cut the front spring while still compressed to release tension.
Yeah I just weld the bottom and add gussets to each side
@thecadillacdanshow8658 thanks for the info my guy. I plan on putting a bridge on my cousins car and was wondering if welding one side on bcuz that's all I can get to would make me look bad. I watch all your vids and gonna build AArms and everything else the way you do it.
@@coolchucho271 the only time I weld both sides is when I fo a full frame I have never had one fail
@@thecadillacdanshow8658 I see gotcha
Do you SLEEP? IF you do you build cars in your DREAMS.❤
I sleep on occasion
outstanding
Thank you!
How can I contact you?
Facebook is best
Spray bedliner on the roof frames
Good idea!
@@thecadillacdanshow8658 I do that to my trunk and floorboards
Got all my fingers n my face 😂😅
Are you for hire?
I am but I am booked up for the next few months
@The Cadillac Dan Show no problem I can wait. What's your contact info
Message me on Facebook
Ospho then paint
Get that POR.. paint over rust, it's more durable that paint
Yeah I have used that and it is a amazing product just expensive
I’m building my 88 euro nose cutlass as we speak. Frame off. Are you not in Ohio ?
I'm in Alabama
@@thecadillacdanshow8658 oh man sorry not sure why I thought you was in Ohio. I’m in Ohio.
@@thecadillacdanshow8658 in your opinion if I’m not hopping or 3 wheeling do I need to bother reinforcing the frame?
@@hosscaddy I would at least do the rear arches as a very minimal you are adding alot more weight then the frame was designed to hold think of holding a brick in your hand with your arm extended all the way out eventually it's going to get tired and drop
@@hosscaddy if you need some work done you can get up with maximino de Leon he is in Ohio. If you havnt already check out the channel gem city welding billy is also in Ohio
You seem to care about your work. That matters that it just not another job.
Yeah I want every set up to stand out. It's a terrible business move but for now I basically build cars for fun. I dont enjoy doing basic setups but I do need to get in the mindset of that's only what most people want to pay for. I have just been lucky to get cool customers that are open to adding changes
@@thecadillacdanshow8658 I wouldn't say it's a terrible business model, it's indeed what will keep you in business. If it's still fun for you to do, then you're on the right track. I've had a 83 coupe and a 90'd out 84 sedan on juice, just hard to find for a good deal now days. The ones I do find are too pretty to cut up. Nice work tho man, take care.
Were be my lowrider green regal at are you ACES-WHIPES or some cat that trys to fix my stuff in junk it
Your face is a unique setup. Giggity.
Is that a good thing or bad thing
@@thecadillacdanshow8658 goood
DIE GRIND SPRING IN PLACE EASY
Hate to see an older car get trashed in the name of bouncing a car to death
I didnt remember you being the owner of the car
@@thecadillacdanshow8658That part
Do you do work on other people's lowrider I need one did the same type setup let me know payment on deck
I do I am booked up for a few months right now when are you looking to build something
@@thecadillacdanshow8658 this fall I'm trying to buy a 83 Buick regal limited
@@terrencesmith3574 let me know I get you in line hit me up on Facebook messager
I need to make a bridge 😔 got any tips man? Im in Aus 🦘
I use 8 inch c channel but there are many ways of building bridges I have seen them out square tube and flat bar