Это видео недоступно.
Сожалеем об этом.

Yanmar 6EY22 Marine Diesel Engine Maintenance 3 Adjustment of valve clearance ضبط التاكيهات

Поделиться
HTML-код
  • Опубликовано: 10 авг 2019
  • Yanmar 6EY22 Marine Diesel Engine Maintenance

Комментарии • 34

  • @Naren_oceanlove
    @Naren_oceanlove 4 года назад +1

    Very helpful 😊

    • @SASplatform
      @SASplatform  4 года назад +1

      Thank you :)

    • @romanjaiani3308
      @romanjaiani3308 3 года назад +1

      @@SASplatform mr meaning 3-4 T i know but say me pls what the meaning 3-4 B.meaning

    • @SASplatform
      @SASplatform  3 года назад +1

      Yes, I did told you in another comment of yours.
      But let me tell you here too 🙂
      It means that pistons number 3 and 4 are at the bottom dead center BDC.

  • @mec6953
    @mec6953 2 года назад +1

    brother, sometimes i see people take a magnetic dial gauge, set it on valve bridge, to adjust "zero point". sometimes i see no one perform this. so, i am bit confused.

    • @SASplatform
      @SASplatform  2 года назад

      Let me say it that way:
      "Old is Gold"

  • @kevinpenaredondo1275
    @kevinpenaredondo1275 3 года назад +2

    what is the condition of the engine while adjusting tappet clearance? what are the preparations before the job? how many months/ running hours for adjustment of tappet clearance?

    • @SASplatform
      @SASplatform  3 года назад +1

      Thanks for your inquiry.. 😊
      The condition is the engine is shut off and cold.
      No preparation needed, only be sure it won't accidentally run while doing that and use proper tools and take safety precautions.
      And the intervals between the checks/adjustment are according to the manual (the engine manual).
      You are welcome any time to ask.. And please, feel free to share the videos. 👍

    • @romanjaiani3308
      @romanjaiani3308 3 года назад +1

      good👍👍👍

    • @neron7625
      @neron7625 Год назад +1

      @@SASplatform It would be nice to have more videos about the generator, like generator parts and performance tuning.

    • @SASplatform
      @SASplatform  Год назад

      We wish to have this soon. Thanks for asking

    • @neron7625
      @neron7625 Год назад +1

      @@SASplatform thank you too, more yanmar videos, water and fuel systems too

  • @robertopacheco2420
    @robertopacheco2420 3 года назад +1

    Our auxiliary engine exhaust temperature very high 450 degrees i already calibrate the injector, replace plunger barrel and adjust tappet clearance and changed oil but exhaust temp. Very high..whats the problem?

    • @SASplatform
      @SASplatform  3 года назад +1

      Check the combustion pressure.
      Also check fuel specifications and take a sample for analysis to compare it with the fuel specifications recommended for the engine by the manufacturer

    • @scoccito
      @scoccito 3 года назад +1

      adjust the racks of the f.o pumps..

    • @robertopacheco2420
      @robertopacheco2420 3 года назад

      Thank you every one I already solve the Problem, The causes is
      Aircooler Fins was clogged up lock of suction air.

  • @FaisalFaisal-pc7ko
    @FaisalFaisal-pc7ko 2 года назад +1

    Sir can you tell me please,my generator brand yanmar is one of the cylinder is very high temperature exhaust gas (370) degree Celsius and the other cylinders is 220 up to 250.what I have to do to make it normally,thank you

  • @romanjaiani3308
    @romanjaiani3308 3 года назад +1

    what the meaning 3-4 B ?.thanks

    • @SASplatform
      @SASplatform  3 года назад +2

      It means that pistons no 3 and 4 are at the bottom dead center BDC

    • @romanjaiani3308
      @romanjaiani3308 3 года назад

      @@SASplatform thanks so much

    • @SASplatform
      @SASplatform  3 года назад

      You are welcome any time 🙂

    • @romanjaiani3653
      @romanjaiani3653 2 года назад

      hello my dear frend. have you some video about D/G sulzer. acsample valve clears? thank you before

    • @romanjaiani3653
      @romanjaiani3653 2 года назад

      the D/G model sulze 4S20H 3CWF (4strok)

  • @dzulkefliesabdin5622
    @dzulkefliesabdin5622 4 года назад

    No sound

    • @SASplatform
      @SASplatform  3 года назад

      We apologize for the sound, but no voice comment needed as the steps are clear.
      Thanks for your feedback. 👍

    • @dzulkefliesabdin5622
      @dzulkefliesabdin5622 3 года назад +1

      Can explain the setting for adjustment screw of bridge valve?

    • @SASplatform
      @SASplatform  3 года назад

      Sure.
      First..
      There is a clearance between the valve bridge and the valves itself, this clearance must be Zero, this done by the screw and the not on the valve bridge..
      Second..
      There is a clearance between the rocker arm and the pushing rod, this clearance must be Zero, this done by simply press on the rocker arm end so you be sure that it is Zero gap between it and the pushing rod.
      Finally.. You will end up having gap only between the rocker arm and the valve bridge, you can check for its clearance number (here in this model 0.4 fir intake valves and 0.7 for exhaust ones.
      We hope we answered your inquiry and you are welcome anytime to ask us.
      😀👍

    • @dzulkefliesabdin5622
      @dzulkefliesabdin5622 3 года назад +1

      Very helpful..Thank you very much for the explanation..

    • @SASplatform
      @SASplatform  3 года назад

      You are so welcome 😀.
      Please feel free to share the videos. 👍