Ford 5000 Brake Rod Seal Replacement

Ford 5000 tractor Brake Rod Seal replacement.
Repair a leaking seal on the brake rod shaft going in to the back end of the tractor.
00:00 Clean the surfaces
00:28 Remove retaining pin
00:53 Remove retaining bolt from brake lever and fixture
01:06 Crack brake rod shaft nuts
01:17 Unscrew brake lever fixture and lock nut
01:29 Remove retaining clip and washer
01:49 Clean rod shaft threads and tape for protection
02:09 Remove old seal
02:47 Install new oiled up seal and push in inner seal ring if possible
03:33 Reinstall locking nut and lever fixture to the same adjustment position
04:21 Reinstall retaining pin
04:38 Remove retaining clip and washer to push in inner seal ring if needed
04:54 Fasten retaining clip and washer

[@JamesOliverHK]

Thanks for taking the time to make that, the use of hose to protect the threads is a great idea too.

[@markreilly456]

Great Video! I have an old Ford 555 with the same problem. After watching your video, I gave it a try. Worked like a charm! Thanks.

[@Roubian1]

Thank you! This saved me hours of trying to figure it out.

[@juanhernandezreyes8951]

Great job!

[@krishritsumret3558]

Good job.

[@ASTAROTH13666]

I have a ford 550 from 82 or 83 and have a constant hidrofluid leak,the mechanism of it looks very similar to yours.does the leak happen because solely of thatt rubber boot/seal or it might be something else?also any idea if i need to drain the hidrofluid?
Totally new to ractors so any tip is greatly appreciated.

[@stevec9653]

The inner part of the boot needs to be pushed another 25mm up the rod it sits in a recess

[@almightyamateur3648]

ruclips.net/video/BlYY1ffa0YU/видео.htmlm40s

[@falarequestretvjorgecarval4263]

Hello .
Could you help me ?
Bought a 1975 Ford 5000 and did all the recovery myself .
But there is no power in the arms .
Cant lift a 300 kg hay bale.
Have no leaks on the arms and replaced the rubbers of them.
I was told it was the hidaulic pump.
Where is it the hidraulic pump ? And what can I do . Thank younso much

[@mrmobius2000]

I am doing this job on my 4610SU. The left side seal replacement went just as is shown in your video. I have ruined 5 seals trying to replace the right side seal. Using calipers, I have determined that the right side hole in the rear axle housing is about 1/10 of an inch too small. The relevant OD on the seal is 1.977 inches; the ID of the hole is 1.875 inches. I believe the hole in the rear axle housing is out of spec. Have you or anyone else encountered this dilemma? It seems my options are give up and get a different tractor; find a replacement rear axle housing and install it; remove the rear axle housing and find someone who can machine the hole to spec. Replacing the axle housing or having it machined are both huge jobs that I am pretty sure my local New Holland dealer would decline to perform, citing staff shortages and the cost/benefit of fixing a 1981 4610SU.
Any other options are welcome. So far this debacle has chewed up a week for a job that should take a couple of hours at most.

[@almightyamateur3648]

No sorry, did not encounter any problems like that. Looks like it’s the same replacement part number aswell for both models so something seems off with your specimen. And there is nothing left over like a ring from another old seal or something stuck in the hole? All I can think of is to somehow squeeze the seal a little bit to reduce it’s size, but that might ruin it aswell. Or maybe another seal with a smaller diameter for another tractor model. It’s a long shot.

[@donames6941]

Put your seal in the frezzer overnight, and press the seal in after it warms up push the rubber over the shalf

[@emmanuelmutai4603]

How do get ford 5610 manual??

[@nickmaggio4019]

what is the part number and where did you get it ?

[@juanhernandezreyes8951]

Does all the hydraulic oil need to be drained or not? I have Ford 6600 80'

[@almightyamateur3648]

Can’t say because I’m not familiar with that model. This one had already lost quite much rear end oil. You could drain a gallon or two and put it back in after, if it looks clean and usable. You could also park the tractor on some wooden blocks to tilt it sideways that way you get more space to work with and the oil flows to the other side. Just be safe.

[@timtalaski5904]

I need a video on how to repair the PTO brake on a 5000

[@pashootist5354]

These might help some.
Ford 5000 PTO clutch pt1
ruclips.net/video/RfIPU7ROjIw/видео.html
Ford 5000 PTO clutch pt2
ruclips.net/video/p6fTBuUHa6Y/видео.html

[@timtalaski5904]

@@pashootist5354 thank you for the info, will give me a lot of confidence when I tear into mine. I appreciate it

[@kedronpful]

Yes seal needs to be pushed way on up the rod and seated in the groove.... That's gonna leak

[@almightyamateur3648]

ruclips.net/video/BlYY1ffa0YU/видео.htmlm40s

[@kedronpful]

Yes that's it!! Didn't see that before.

[@jackdurham5601]

​@@almightyamateur36484:40

[@donames6941]

You didnt show pushing the seal on to the rod yor way it will leak