Conveyor Gear box removal

We show how to remove a Baggage Handling System, Bhs gear box and motor removed from shaft. The Gearbox can take a hard set on the shaft after years of service. A custom made pulled plate is used to pull the gearbox off the shaft. Anti seize should be used on the shaft when reinstalling the gearbox.
Sew Euro drive motor driven by vfds with a gear reduction gearbox mounted on drive shaft
More video training videos for conveyor maintenance
Baggage Handling System BHS
• Baggage Handling Syste...
Conveyor Plow Diverter Belt Replacement • Conveyor Plow Diverter...
Replace a merge belt using a belt puller
• Change a Merge Belt on...
BHS belt cutting and lacing
• Conveyor Belt Cutting ... ​​
Preparing a Conveyor Belt for lacing • Prepare your conveyor ...
How to change a conveyor Belt
• Conveyor Belt, how to ...

[@jamesladd]

We usually use a gear puller but I like your method as well.

[@miker8623]

James Ladd. Where I work we have similar gearboxes. What is an easy way to install. I’m the real world they just don’t slide back on.

[@Mohow-fv2vq]

@@miker8623putting a bold with a big washer in the ax. And same principle as in video. And please use a lot of grease. It will help next time.

[@78945612able]

@@Mohow-fv2vq Anti-seize helps a lot.

[@IngDzib]

Thanks regards from Cancun

[@joseenriqueagustin9597]

Me encanto la forma, que yo sepa debería salir deslizantes, ahora mi pregunta es la siguiente. ¿ Cómo encuentro las dimensiones correspondiente para fabricar este extractor?.
Se me seria muy util ya que me dedico al mantenimiento de faja transportadora pero quiero realizar estos extractor, pero no se como buscar las dimensiones del reductor.

[@180Floridalife]

Ve a la página de la comunidad en mi canal y mira la publicación más reciente. Para fotos detalladas del motor extractor. gracias

[@hi-pwr]

What are the dimensions of the screws you used in this ocassion?, by the way it looks in the video, plate thicknness is around ½ in. Also, if possible, do you remember what kind of style of screw is, standard, extra fine, etc?

[@180Floridalife]

The screw is from a puller set, i believe it was 1/2 fine thread. 12” long

[@faroukalgawish5209]

Is this way having bad impact on hollow shaft bearings?
I think this gearbox should be overhauled after dismounting this way

[@180Floridalife]

We have had no issues with gear boxes removed this way.

[@shhmallbudoo2377]

I put these on all the the time on conveyors. Mostly 107s

[@nacerayoub1963]

Un travail provisionnel, merci

[@180Floridalife]

de rien, merci d'avoir rejoint la chaîne

[@miker8623]

Do you have a video on how to put it back on

[@180Floridalife]

I don’t but that’s a excellent idea for a new video. Thanks for watching

[@amillimartin1456]

Can you show us the plate that you made please 🙏🏾

[@180Floridalife]

I’ll see if I can find some pictures and post them on the channel. There are some RUclips shorts on my channel that show it closer

[@180Floridalife]

I have posted pictures on my channel under posts, enjoy

[@gmarine357]

Do you have more images of the plate.

[@180Floridalife]

I have posted pictures on my channel under posts

[@kingsupra5023]

Which Gearbox oil good for this Gearbox

[@180Floridalife]

mobilgear oil 600 xp 220

[@somethinguseful2935]

Thank you

[@faroukalgawish5209]

Thanks

[@deadshotmotorsports7856]

I would have like to have seen what the other end of the threaded rod, how dose it push on the pulley without hurting the roller.

[@180Floridalife]

Thanks for watching, it’s a standard pusher rod, robbed out of a gear pulled, so the far end has a rotating flat head on it

[@ronaldolopes2391]

How thick is the board in mm?

[@Scousedave2005]

You got the dimensions as this be handy for me to make

[@180Floridalife]

If you go to the community tab of my channel there are some close up photos of the puller to help make your own. Have a great one ☝️

[@selvamveerayah305]

can send me how the plate looks like sir/

[@180Floridalife]

I’ll see if I can find the pictures

[@180Floridalife]

I have posted pictures on my channel under posts thanks

[@cheikhsidatydiop7521]

I need to see the plate . I want to bring out one of this more complicate

[@180Floridalife]

Check out some of my shorts for a
Closer view of the puller

[@180Floridalife]

I have posted pictures of the plate on my channel under posts thanks

[@ash6356]

Is this tool available out there in the market?

[@180Floridalife]

This is a shop made tool

[@ash6356]

@@180Floridalife cool!!

[@bigstatercak2193]

Cool

[@180Floridalife]

Very cool indeed 👍 thanks for watching

[@dhawk7628678]

What's the purpose of the metal Jerry rig plate

[@180Floridalife]

It is a gear puller used to pull the motor off the shaft. The motor and shaft take a set and are very hard to remove

[@Bigrig_trmc]

Why not use an impact instead of a ratchet??? It’s wat I use cuz it works faster and less work lol

[@180Floridalife]

With the impact I would worry about damaging the shaft or the gearbox. Removing it by hand allows you to feel when something goes wrong, and lowers the chance of mushrooming the shaft. Thanks for watching and have a great one

[@marouanattioui9031]

HELLO NICE WORK, COULD YOU PLEASE SEND ME THE PLATE

[@180Floridalife]

Sorry can’t sent the plate but there are detailed pictures in the community section of my channel. Thanks

[@javiermartinez1929]

Ya me habias espantado kimo

[@180Floridalife]

¡no temáis!

[@xxxdpgxxxx1389]

What did this plant produce aluminum cans ?