thanks for the video , i have a ZMR blheli 50A ESC and got stuck in the bidirectional mode, which disabled the programming mode, i followed the video but the ESC is not recognized by the BLHeliSuite nor BLHeliSuite32 .. how can i exit this bidirectional mode and make it forward ?
Is there any way to control the motor with arduino interface ? I have just the motor + blheli_s 30A + arduino . I can flash but I don't know how to test the motor .
@@ColtonCampbell Thanks for the answer . Yes I have a 12Volt power supply hooked to Blheli_s , and I was able to write configuration to Blheli_s with arduino when the power supply was connected. What I want is to run the motor.
Hi, I am using an arduino uno and the HobbyKing® ™ Brushless Car ESC 10A w/ Reverse ESC. I have followed your tutorial, but it doesn't seem to work. What can I do? (The problem is that it doesn't detect the esc). Thanks!
Hello Colton, I want to flash the firmware to the DYS 30A ESC, for this they have used Simon K firmware but I didn't found in target ESC option in BL Heli suite 16, how can I flash the firmware to DYS 30A ESC
hey nice tutorial, just one question .. i have a blheli_s 4 esc board and i want to flash / use it with arduino nano .. how can i do that .. ? the blheli_s board has 4 signal pins btw, just like the normal single esc, so i thought maybe do it like that? help pls
Unless you have a board with 4 ESCs on it there is only 1 signal pin and it is usually a thin white wire. The other 3 are power and ground for connecting it to a power supply (usually battery) - these would be the slightly thicker wires and the last one is another ground for connecting to the microcontroller GND
@@theodordimov6518 Hey, thanks! It's been a year so I fixed that issue a long time ago. I ended up using BLHeli_Suite to flash the 4-in 1 esc board by connecting each of the 4 input wires to 8, 9, 10 and 11 of the Arduino nano. I then proceeded to flash an interface fpr 4-in 1 on the nano using the Arduino Uno template (Nano template has a bug). I got in, and configured myesc board. I have been using it since and even corrupted the controller once on the board where I had to manually flash using the tiny configuration pads on the board. I did a successful jump flight that crashed a bit later but still was progress because I'm writing my own flight controller. So far I accidentally fried the first few mosfets on the board by accidentally shorting the power. It was due to a false connection woth the capacitor. So now I bricked it and am using that same board with a spare singular.
Hi, i have an unbranded esc with green pcb and two chips, one is fortior fd6288t and the other chip does not have any labels. Help me identify what esc is this please D:
@@ColtonCampbell hhh thank you anyways brother. I gave up, I spent two days searching on Google and asking everywhere and nobody knows what esc it is. Im just gonna buy a blheli ready esc lol Have a good day :D
What chip does your ESC use? Or what was it branded as? You might have to open the heatshrink like I did to see what chip your ESC uses (Atmel 8a, etc)
Hello I am using YEP 40A ESC with Arduino Mega 2560 (PIN D51) and I get the following error. Serial Interface “m4wFCIntf” connected successfully. Connection to ESC#1 failed! Please check data- und power-connections to ESC! Kindly help in this regard.
I need some help please, I've got this ESC: hobbyking.com/de_de/turnigy-multistar-20a-v2-esc-with-blheli-and-4a-lbec-2-6s.html and an Arduino Uno. If i do everything like you did in the Video, I can connect the Arduino with BL-Heli, but after I press "read Setup" the Programm says "Please connect the ESC and power up". After 15 Seconds there is an error message. I don't understand why this Messages Comes, because i connected everything like you told (GND -> GND / Data -> Digital Pin 2) Could you help me?
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Very well explained tutorial! Short and easy to understand for a newbie! Thanks for your time :-)
Im glad it helped! Thanks for the comment
Very well explained.... You just got another subscriber.
Thank you!
Love you man !
thanks for the video , i have a ZMR blheli 50A ESC and got stuck in the bidirectional mode, which disabled the programming mode, i followed the video but the ESC is not recognized by the BLHeliSuite nor BLHeliSuite32 .. how can i exit this bidirectional mode and make it forward ?
Is there any way to control the motor with arduino interface ? I have just the motor + blheli_s 30A + arduino . I can flash but I don't know how to test the motor .
You would need a battery / power source more than just the Arduino hooked up to the ESC
@@ColtonCampbell Thanks for the answer . Yes I have a 12Volt power supply hooked to Blheli_s , and I was able to write configuration to Blheli_s with arduino when the power supply was connected. What I want is to run the motor.
Can you please advise how to find the suitable firmware for the no name ESC
Thank you so much
Can i test the motor directly in blheli didnt finde an option? Great video 😉
Hi, I am using an arduino uno and the HobbyKing® ™ Brushless Car ESC 10A w/ Reverse ESC. I have followed your tutorial, but it doesn't seem to work. What can I do? (The problem is that it doesn't detect the esc). Thanks!
cant get selection on the firmware.. its empty. how to solve that?
Thanks for well explained tutorial
Hello Colton,
I want to flash the firmware to the DYS 30A ESC, for this they have used Simon K firmware but I didn't found in target ESC option in BL Heli suite 16, how can I flash the firmware to DYS 30A ESC
I will give it a shot
there is no arduino due in the board selection in blhelisuite . did i do something wrong or the firmware doesn't support this board?
hey nice tutorial, just one question .. i have a blheli_s 4 esc board and i want to flash / use it with arduino nano .. how can i do that .. ? the blheli_s board has 4 signal pins btw, just like the normal single esc, so i thought maybe do it like that? help pls
Unless you have a board with 4 ESCs on it there is only 1 signal pin and it is usually a thin white wire. The other 3 are power and ground for connecting it to a power supply (usually battery) - these would be the slightly thicker wires and the last one is another ground for connecting to the microcontroller GND
@@theodordimov6518 Hey, thanks! It's been a year so I fixed that issue a long time ago. I ended up using BLHeli_Suite to flash the 4-in 1 esc board by connecting each of the 4 input wires to 8, 9, 10 and 11 of the Arduino nano. I then proceeded to flash an interface fpr 4-in 1 on the nano using the Arduino Uno template (Nano template has a bug). I got in, and configured myesc board. I have been using it since and even corrupted the controller once on the board where I had to manually flash using the tiny configuration pads on the board. I did a successful jump flight that crashed a bit later but still was progress because I'm writing my own flight controller. So far I accidentally fried the first few mosfets on the board by accidentally shorting the power. It was due to a false connection woth the capacitor. So now I bricked it and am using that same board with a spare singular.
Do you have an scematic for wiring my Pixhawk4 with an Arduino uno or an Arduino Mega 2560
Hi, i have an unbranded esc with green pcb and two chips, one is fortior fd6288t and the other chip does not have any labels. Help me identify what esc is this please D:
Sorry dude, I have no idea! All I can say is Google and rcgroups.com is your friend. Good luck!
@@ColtonCampbell hhh thank you anyways brother. I gave up, I spent two days searching on Google and asking everywhere and nobody knows what esc it is. Im just gonna buy a blheli ready esc lol
Have a good day :D
I dont know wich blheli firmware I have to flash on my SIMONK 30a .
My type does not show on the flipdown page .
What chip does your ESC use? Or what was it branded as? You might have to open the heatshrink like I did to see what chip your ESC uses (Atmel 8a, etc)
Hello
I am using YEP 40A ESC with Arduino Mega 2560 (PIN D51) and I get the following error.
Serial Interface “m4wFCIntf” connected successfully.
Connection to ESC#1 failed!
Please check data- und power-connections to ESC!
Kindly help in this regard.
Did you manage to correct this error ? I have the same issue..
@@pthyr same
Do you know if it is possible to read out an bricked PX4
Sorry I just now saw the other comments. I'm not sure how to fix a bricked pixhawk unfortunately
Does this work with EMAX 20A esc?
It should! Give it a try.
I need some help please, I've got this ESC: hobbyking.com/de_de/turnigy-multistar-20a-v2-esc-with-blheli-and-4a-lbec-2-6s.html
and an Arduino Uno. If i do everything like you did in the Video, I can connect the Arduino with BL-Heli, but after I press "read Setup" the Programm says "Please connect the ESC and power up".
After 15 Seconds there is an error message.
I don't understand why this Messages Comes, because i connected everything like you told (GND -> GND / Data -> Digital Pin 2)
Could you help me?
You might need to use a different digital pin for the Uno, try switching that first. Do you have the esc powered?
@@ColtonCampbell i've tryed everything, but nothing worked, thats why I don't know why :(
@@crouserhd297 even I am having the exact same issue.. please let me know if you find the solution..ty
I heard that pin 11 works best for the UNO board for this task. Haven't tried it out myself though.
THANKS!
😂😂😂 ok no problem.But if you want a challenge try and unbrick a PX4 .If you succeed you would be a hero to all PX4 users😁😁
I mean with Arduino Mega
Yeah should work fine
Hey i can’t catch up what are you saying. Put a subtitle please 🥲
Hello. Can i use Arduino Uno for this purpose? Or maybe Nano?