Bought one of these a week ago and dove straight into it. Ended up back rolling a fair bit as the standard tip seems to chunk out 10% watered down emulsion at medium pressures. Thanks for the advice with the different tips, just bought some off of amazon. Great vid, thanks again
well im not one for commenting but i think you have just sold it to me. im doing a house up and think i need one of these now. plus need to paint the outside of the house too, the 9m pipe will be fantastic for this job. thanks for the video. keep up the good work
Hahah, just be sure to watch videos on how to use airless, they can be a real nightmare at the beginning. Once going, amazing, just remember to make sure your paint is thin enough, thick paint doesn't work well so you mayeb need to thin your paint.
@@sgpaint hello again. I managed to get a sprayer the same as yours. Oh dear lol. Things went ok. Fantastic results but. When you sprayed did it fill the room with fine paint. I had a mask on but should of put the bigger mask and not the paper type. Think iv almost killed myself. It's gone everywhere. No idea if iv done it properly. Hope you can help
@@oakeydoke78 practice makes perfect. You'll be fine but be sure to use a very good mask in future, or if you're spraying more than once a year. Turn the pressure down if you have lots of overspray. Use a RAC X low pressure tip, they help to reduce overspary (the mist that fills the room)
@@sgpaint thanks again for the reply. Just looked on Amazon for one. Graco ones are £30 ish but loads of spray types any idea on what number to get or a pack. Sorry for all the questions lol. And a mask is going to be on full time lol.
You now know about tip sizes? first number is the fan width.... double the first number.. give you it in inches.. a 5, will give you a about 10" fan.. spray about 30cm away from the surface. The other two number is the orifice size (the hole the paint goes through on the tip) the bigger the number.. the bigger the hole, more paint goes through it.. or thicker paint can get through it. Smaller number will be better with thinner.. finish/woodwork paints etc. Can you alter the spray pressure on it ok?
I’ve got one of these and yeah you just adjust the regulator. I’ve actually fitted a gauge to mine. Maximum on the regulator is 2500psi when you release the trigger and the pump builds the pressure. Minimum is about 1000psi. Watched quite a few of your vids so thanks for the tips and advice
@@Capo-xc1ji don’t think I’m able to put a picture up on the comments. I got a gauge T piece 1/4” BSP. Goes between the outlet from the pump and the sprayer hose. Then a 1/4” bsp gauge that’s 0-3000psi I went to a local hydraulic place and they had pretty much everything I needed. If there’s any way to private message me on here send me your email and I’ll send a pic. I found that basically with the machine maxed out it’s about 2500psi
Sold out already!!!! Wow, sorry I think this video might have something to do with it as they were well stocked the day before this video went out. Do get one, its a great bit of kit and a good starting place for anyone wanting to get into it.
Great video mate! clear and concise. I am a novice and just broke the machine out after buying it last year (took that long to get refurb done). I watched another good video and he said that the GRAKO tips fit. So I went out and bought a 210 and 310 and they don't. What make to you use? Alternatively Do you know if i can buy the spray Guard and that will fit the Erbauer gun?
I would also recommend to anyone on the fence about buying this to get some other tips off Amazon. The tip it comes with drinks paint like there's no tomorrow so definitely go for a smaller tip!
Fantastic video , well and truly explained, good info to know before paint is ready to go through, hopefully see a video with it in operation , just to see the performance side of things , I'm a paint and decorator by trade and want to make the transition towards airless , especially when asked to paint new builds , good job keep it up I will like and subscribe 👍
If you do new builds a sprayer is a must been spraying for 20 odd years.. you can spray out a 350sqm house in four hours... I'm not sure if this would handle constant use but if its comes with 3 year warranty its a must... make sure you can buy spare parts your gona need them..
I invested in this unit recently. Set up and priming the unit was straightforward, however, I'm struggling to find additional tips to use with the gun. I bought a Wagner 211, and whilst it fits, the machine would stop spraying. I'd change it back to the tip it was supplied with and it worked fine, put the Wagner back in and it stopped. Checked for blockages and there weren't any. Ended up going to Brewers for some advice, they ended up calling the manufacturer who advised that this unit has not been designed to work with anything other than what it comes with. Very disappointed to learn this, but I will give the tips from Amazon a go as there must be something out there that works.
I just bought one of these, put it together but not used yet. What's the function of the narrow clear tube ? Where does that go ? Not in the paint I think. I'm planning to use .Emperor Creme' waterproofing 'paint' on exterior brickwork and its very viscous.
Bought and used mine today, however it started to leak out through the spray Nozzle area of the gun 🤦🏻♂️🤦🏻♂️ any ideas why? It was secured well aswell
I was looking to buying one of these as want to get into airless spraying and I ended up getting the refurbished one it arrived and it had two left feet in box so couldn't use it 😅 ...
Can you do a video of cleaning it please? Maybe even a full tutorial? I just bought one and completely new to spraying . Also the 517 tip that comes with it seems to be stuck?
Looking to buy this sprayer, very informative video, thank you. Could you put a link up for the compatible tips and extension bar you bought off Amazon please. Thank you.
Great video.. it has convinced me to go and buy one! although most stores are out of stock. The main reason is to repaint all the woodwork in the house inc. doors, I have used WRX satinwood before but brush marks can be a pain and it doesn't say about being able to use it in an airless. What satinwood paint would you recommend?
Might be a bit late but Johnson’s Trade Aquaguard sprays nicely and stands up to some abuse. Dulux Trade Diamond satinwood is great too, sprays with far better opacity than brush application and is probably the hardest wearing outside of ScuffX. Hope this helps you or someone else who might happen across this!
Hello, a very good video, I’ve just bought the same sprayer, and I must say it seams good value for the money, have you tried it with a whip hose, if so which one did you get, cheers 👍
Cheers bro I was wondering for weeks would it be any good Ur after answering my questions and thoughts on it pretty clearly ...so have u used it much since this video has it paid for itself would you think !!!
Use it All the time. paid for itself by the second time I used it. If you really keep going woth it, you'll start making serious $$$ without rushing. See other videos
@@sgpaint cheers my guy was wondering was it worth it as I work in the industry myself iv had a pro Wagner stolen off a building sure when I went to local shop to get lunch , never buying an expensive machine again after that lesson
Just picked one of these up and did our spare room (it’s £170 at B&Q at the minute, but 200 at screwfix!) Completely agree with your review, lovely little unit, but my god it drinks paint with the 517 tip… just used some contract matt thinned about 10-20% and a it must have gone though about 8 odd litres on a medium sized bedroom… that might be about right but it sounds a lot to me! I bought 5l of the colour we’re using and I was expecting that to do 2 coats (albeit with a roller) What tip size do you recommend for emulsion? I was happy with the 5 fan size for walls, but I think the 17 tip size is just too much - especially for a beginner. I was thinking a 515? You mentioned a 315 and 215 I think… that sounds quite narrow for walls/ceilings but I’m new at this! Also what tips did you buy, were they any good?
Great vid! Hows the finish on wood using lacquer and/or eggshell paints? Is the atomisation very fine, do you see splutters? Could you use it on furniture or homemade cabinets?
Yes its a good finish, no slappaering, I filtered the paint and didn't use an extention. Have a video of results on my Facebook page S&G painting and decorating
Can you do more videos on this product. I’m in two mind whether to get this or Wagner. Also should I go with roller or airless? Does this have much overspray?
Should be super easy. Undo the gun, using your hand. Think I have another video showing... check my other videos.. it took me a while to figure out also 😄
Hi just got one of these, set it all up, primed it first the turned to paint but doesn’t switch off by handle just keeps spraying constant any ideas? Have I done something wrong
Great video thanks. I had spotted this unit in Screwfix but hadn’t seen a review anywhere. My only issue with Erbauer gear - and I have owned other erbauer tools I was very happy with - is that repairs/spares are difficult/impossible to come by. I really don’t hold with disposable tools in this day and age. I wonder what the after service is like with Wagner?
Hola, que tal? Tengo una duda respecto a los materiales que se pueden usar con esta máquina, mi pregunta sería; se pueden utilizar pintura sintética, esmaltes, lacas, barnices a base de disolventes ó solo se pueden utilizar productos con base de agua?
dice que se pueden usar otra tipa de pintura aparte de una con un base de agua. Pero no estoy seguro como seria. Pero si, lo compre el otro dia y dice que si, es possible
Thanks for posting. Any tips on paint thickness? I’ve been using a Screwfix standard water based undercoat / primer and it makes fingermarks down the sides when spraying and eventually wouldn’t make any pressure just kept charging so I’m guessing possibly the paint is too thick??
Doesn't look like it would last long spray the walls and ceiling and see how hot it gets .... did it spit on any of the doors... take the gun filter out that's the first thing I do with new guns...
Its been fine, at the price i don't expect it to be great but time will tell i guss. Did spit a bit but once I filtered the paint it was fine. So you use the gun without a filter?
@@JONO3679 going to give this a go. I'm sure if the paint is well filtered in advance it shouldn't really need this filter? Will give this a go anyways, why not.
@@sgpaint been spraying for 20 odd years had Wagners graco have done this with all of them. Has for guns I use to buy the 300 doller guns bought one off ebay for $30 was just as good always a good idea to have a spare. Find out if they sell the spray prime valve and inlet outlet valves .and a diaphragm if you have these that machine is gold..
Not bad piece of kit considering the price of the high end equipment, but I cannot believe what a mess everything is. Paint everywhere including all over you. I used to be an offshore sprayer using airless, I was also a vehicle refinisher using both types air and airless, the latter was used on HGV Trailers. My ocd would be doing overtime trying to cope with the state of the equipment and the place lol...
Hi, i need some help. I bought this machine, but i'm struggling with it. I tried with water, and it works perfectly, but with the paint, does not work... Can you do a review with the inicial instructions, please!
Drop me a message on my Facebook page; S&G painting and decorating. I can talk you thought what to do. I will do a video but super busy at the mo so not for a while.
As soon as you type in tips you'll see its 4 blue tips... tbh I wouldn't really waste my money, best to just get higher end ones, make a huge difference.
I simply cannot unscrew the nuts that hold the trigger guard on, I need to do that to get the handle off to clean the filter. It's brand new. I don't why they fastened them on so tight, but it's utterly IMPOSSIBLE to budge either of them. Anyone else had this annoying problem?
I bought this today to paint fitted MDF panel wardrobes. Im guessing the standard tip is no good for the job ?? Any ideas on what size tip i should be using please??
Anybody there to help? I'm on my new machine. Followed the instructions step by step and was spraying away and it just stopped on me. When I turn it off and put it back to prime its working but the power just stopped on spray?
Cowboy stuff you don't need it in a house , easy normal walls, it's only for awkward ceilings , pebble dash walls, and maybe if your doing loads of new builds
Cowboy stuff? Really? I’ve been an interior renovator for well over 25 years, I have a 100% rating, so it’s fair to say I’m no cowboy, and I routinely use airless spray. I would use HVLP for cabinets, but that’s just me, but this was a good video. I’d love to know where the cowboy comment comes from? If you’re in the trade, I can only assume you’re privy to something us mere mortals are unaware of!
Hi all, could someone please help me, I have this sprayer, went to use it for the second time yesterday, I don't know what I have done wrong but it's leaking out before the tip, I have given am extra good clean at home buy what have I done wrong, please help , in the middle of a job grr 😡😡
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
Bought one of these a week ago and dove straight into it. Ended up back rolling a fair bit as the standard tip seems to chunk out 10% watered down emulsion at medium pressures. Thanks for the advice with the different tips, just bought some off of amazon. Great vid, thanks again
Just sharing the wealth as so many do on youtube. Thanks, I have another spraying doors
Another video. Will make more
This video was Very helpful thanks 👍
well im not one for commenting but i think you have just sold it to me. im doing a house up and think i need one of these now. plus need to paint the outside of the house too, the 9m pipe will be fantastic for this job. thanks for the video. keep up the good work
Hahah, just be sure to watch videos on how to use airless, they can be a real nightmare at the beginning. Once going, amazing, just remember to make sure your paint is thin enough, thick paint doesn't work well so you mayeb need to thin your paint.
@@sgpaint lol hoping I'll be ok but will water down as you say. I'll let you know if it explodes up on me lol. Thanks for the reply
@@sgpaint hello again. I managed to get a sprayer the same as yours. Oh dear lol. Things went ok. Fantastic results but. When you sprayed did it fill the room with fine paint. I had a mask on but should of put the bigger mask and not the paper type. Think iv almost killed myself. It's gone everywhere. No idea if iv done it properly. Hope you can help
@@oakeydoke78 practice makes perfect. You'll be fine but be sure to use a very good mask in future, or if you're spraying more than once a year. Turn the pressure down if you have lots of overspray. Use a RAC X low pressure tip, they help to reduce overspary (the mist that fills the room)
@@sgpaint thanks again for the reply. Just looked on Amazon for one. Graco ones are £30 ish but loads of spray types any idea on what number to get or a pack. Sorry for all the questions lol. And a mask is going to be on full time lol.
Just bought one.... and yes the instructions aren’t great, your video has helped grarly, I will like you get a smaller . Thanks again👍
I just bought one, and for 220£ is no bad at all
You now know about tip sizes? first number is the fan width.... double the first number.. give you it in inches.. a 5, will give you a about 10" fan.. spray about 30cm away from the surface. The other two number is the orifice size (the hole the paint goes through on the tip) the bigger the number.. the bigger the hole, more paint goes through it.. or thicker paint can get through it.
Smaller number will be better with thinner.. finish/woodwork paints etc.
Can you alter the spray pressure on it ok?
I’ve got one of these and yeah you just adjust the regulator. I’ve actually fitted a gauge to mine. Maximum on the regulator is 2500psi when you release the trigger and the pump builds the pressure. Minimum is about 1000psi.
Watched quite a few of your vids so thanks for the tips and advice
@@dave11owlett hi Dave can you show me a picture and details how you fitted the pressure gauge to your machine thanks mark
@@Capo-xc1ji don’t think I’m able to put a picture up on the comments.
I got a gauge T piece 1/4” BSP. Goes between the outlet from the pump and the sprayer hose. Then a 1/4” bsp gauge that’s 0-3000psi
I went to a local hydraulic place and they had pretty much everything I needed.
If there’s any way to private message me on here send me your email and I’ll send a pic.
I found that basically with the machine maxed out it’s about 2500psi
Wanted to buy this unit and they are completely sold out in every screwfix. I hope they restock it as it seems like a great sprayer
Sold out already!!!! Wow, sorry I think this video might have something to do with it as they were well stocked the day before this video went out. Do get one, its a great bit of kit and a good starting place for anyone wanting to get into it.
There cheaper in b n q 170
Great video mate! clear and concise. I am a novice and just broke the machine out after buying it last year (took that long to get refurb done). I watched another good video and he said that the GRAKO tips fit. So I went out and bought a 210 and 310 and they don't. What make to you use? Alternatively Do you know if i can buy the spray Guard and that will fit the Erbauer gun?
I would also recommend to anyone on the fence about buying this to get some other tips off Amazon. The tip it comes with drinks paint like there's no tomorrow so definitely go for a smaller tip!
Fantastic video , well and truly explained, good info to know before paint is ready to go through, hopefully see a video with it in operation , just to see the performance side of things , I'm a paint and decorator by trade and want to make the transition towards airless , especially when asked to paint new builds , good job keep it up I will like and subscribe 👍
Will add a video later and another tomorrow
If you do new builds a sprayer is a must been spraying for 20 odd years.. you can spray out a 350sqm house in four hours... I'm not sure if this would handle constant use but if its comes with 3 year warranty its a must... make sure you can buy spare parts your gona need them..
I invested in this unit recently. Set up and priming the unit was straightforward, however, I'm struggling to find additional tips to use with the gun. I bought a Wagner 211, and whilst it fits, the machine would stop spraying. I'd change it back to the tip it was supplied with and it worked fine, put the Wagner back in and it stopped. Checked for blockages and there weren't any. Ended up going to Brewers for some advice, they ended up calling the manufacturer who advised that this unit has not been designed to work with anything other than what it comes with. Very disappointed to learn this, but I will give the tips from Amazon a go as there must be something out there that works.
Did you find out why what’s tips worked?
Buy a graco tip guard and use the graco tips 👌
Good job well explained bar jerky video but all good, thanks
Please can you post a link to the Amazon page where you got your extra tips???
Great video, thanks
I just bought one of these, put it together but not used yet. What's the function of the narrow clear tube ? Where does that go ? Not in the paint I think. I'm planning to use .Emperor Creme' waterproofing 'paint' on exterior brickwork and its very viscous.
Bought and used mine today, however it started to leak out through the spray Nozzle area of the gun 🤦🏻♂️🤦🏻♂️ any ideas why? It was secured well aswell
I was looking to buying one of these as want to get into airless spraying and I ended up getting the refurbished one it arrived and it had two left feet in box so couldn't use it 😅 ...
Can you do a video of cleaning it please?
Maybe even a full tutorial?
I just bought one and completely new to spraying . Also the 517 tip that comes with it seems to be stuck?
Hi. Love the video im going to get one of these as i have a rental property to do. Have you a video of them working at all?
Great video dude
Any link's on Amazon for the tips please 🙂?
Where did you buy your extra tips from? Thanks
Great video much appreciated 🫡👍
New video of this unit in use added... search 'using EAP600'
Great video
Do you have rhe amazon link to them tips mate
Looking to buy this sprayer, very informative video, thank you. Could you put a link up for the compatible tips and extension bar you bought off Amazon please.
Thank you.
Pick up the graco rac x tips, you'll need the guard also. I use 517, 210, 208.
Great video.. it has convinced me to go and buy one! although most stores are out of stock. The main reason is to repaint all the woodwork in the house inc. doors, I have used WRX satinwood before but brush marks can be a pain and it doesn't say about being able to use it in an airless. What satinwood paint would you recommend?
Might be a bit late but Johnson’s Trade Aquaguard sprays nicely and stands up to some abuse. Dulux Trade Diamond satinwood is great too, sprays with far better opacity than brush application and is probably the hardest wearing outside of ScuffX. Hope this helps you or someone else who might happen across this!
Hello, a very good video, I’ve just bought the same sprayer, and I must say it seams good value for the money, have you tried it with a whip hose, if so which one did you get, cheers 👍
I use muslin for straining paint etc
Cheers bro I was wondering for weeks would it be any good Ur after answering my questions and thoughts on it pretty clearly ...so have u used it much since this video has it paid for itself would you think !!!
Use it All the time. paid for itself by the second time I used it. If you really keep going woth it, you'll start making serious $$$ without rushing. See other videos
@@sgpaint cheers my guy was wondering was it worth it as I work in the industry myself iv had a pro Wagner stolen off a building sure when I went to local shop to get lunch , never buying an expensive machine again after that lesson
Do the Wagner tips fit this straight off the bat?
Very nice, thanks
Just picked one of these up and did our spare room (it’s £170 at B&Q at the minute, but 200 at screwfix!) Completely agree with your review, lovely little unit, but my god it drinks paint with the 517 tip… just used some contract matt thinned about 10-20% and a it must have gone though about 8 odd litres on a medium sized bedroom… that might be about right but it sounds a lot to me! I bought 5l of the colour we’re using and I was expecting that to do 2 coats (albeit with a roller)
What tip size do you recommend for emulsion? I was happy with the 5 fan size for walls, but I think the 17 tip size is just too much - especially for a beginner. I was thinking a 515? You mentioned a 315 and 215 I think… that sounds quite narrow for walls/ceilings but I’m new at this!
Also what tips did you buy, were they any good?
Also nice vid and thanks! I probably would have bottled it if it wasn’t for your videos on this unit.
Hi mate just bought one of these.. Are they meant to be so loud or this just when you hit the handle the generator kicks in?
Great video. What tip came with the sprayer.
517
They are a learning curve by the time I painted my house I was an expert with a lot of mess ups 👍🏻
Great vid!
Hows the finish on wood using lacquer and/or eggshell paints? Is the atomisation very fine, do you see splutters? Could you use it on furniture or homemade cabinets?
Yes its a good finish, no slappaering, I filtered the paint and didn't use an extention. Have a video of results on my Facebook page S&G painting and decorating
@@sgpaint try using a 208 or 308 it gives a much finer finish
@@naurbassant7329 using 208, its lovely
@@sgpaint I know I have a 395 graco as well
Can you do more videos on this product. I’m in two mind whether to get this or Wagner.
Also should I go with roller or airless? Does this have much overspray?
I think good/small tips will help with overspray. now i've got to grips with it, i'm using much less paint. I will make another video.
Sure a have asked but can you use different products tips ie Wagner Graco?
hi loved the video I'm having difficulty trying to remove filter from the gun have you any tips on how to
Should be super easy. Undo the gun, using your hand. Think I have another video showing... check my other videos.. it took me a while to figure out also 😄
how did you do this?? I cannot get any of these nuts off, they are absolutely jammed onto the gun handle and its brand new
@@bertybasset106 there's a fault with them I had to go through 4 machine's until luckily I got one that released
@@michaelmartin673 really that's useless. I wonder if they'd replace the gun if I brought it back. I got it in screwfix
Any chance of a video on setting this up and using?
One day but just a little too busy at the unfortunately. Loads of videos about setting up airless on youtube, same same.
Thanks man, it's helpful
Any advice on viscosity of paint ?
Do you know the maximum nozzle size you can put on it. It brings a 517 and I want to put a 525, but I don't know if it will work. Thank you
Does it spray well ?
Yes it does
And could you use an extension on the gun?
Where can I buy nuzzle for this?
Hi just got one of these, set it all up, primed it first the turned to paint but doesn’t switch off by handle just keeps spraying constant any ideas? Have I done something wrong
Great video thanks. I had spotted this unit in Screwfix but hadn’t seen a review anywhere.
My only issue with Erbauer gear - and I have owned other erbauer tools I was very happy with - is that repairs/spares are difficult/impossible to come by. I really don’t hold with disposable tools in this day and age. I wonder what the after service is like with Wagner?
I think they will just replace the unit. 3 years warranty. I'm planning to buy another back up.
Hola, que tal? Tengo una duda respecto a los materiales que se pueden usar con esta máquina, mi pregunta sería; se pueden utilizar pintura sintética, esmaltes, lacas, barnices a base de disolventes ó solo se pueden utilizar productos con base de agua?
dice que se pueden usar otra tipa de pintura aparte de una con un base de agua. Pero no estoy seguro como seria. Pero si, lo compre el otro dia y dice que si, es possible
Thanks for posting. Any tips on paint thickness? I’ve been using a Screwfix standard water based undercoat / primer and it makes fingermarks down the sides when spraying and eventually wouldn’t make any pressure just kept charging so I’m guessing possibly the paint is too thick??
Doesn't look like it would last long spray the walls and ceiling and see how hot it gets .... did it spit on any of the doors... take the gun filter out that's the first thing I do with new guns...
Its been fine, at the price i don't expect it to be great but time will tell i guss. Did spit a bit but once I filtered the paint it was fine. So you use the gun without a filter?
@@sgpaint yup just stops the gun from clogging up and gets better flow..
@@JONO3679 going to give this a go. I'm sure if the paint is well filtered in advance it shouldn't really need this filter? Will give this a go anyways, why not.
@@sgpaint been spraying for 20 odd years had Wagners graco have done this with all of them. Has for guns I use to buy the 300 doller guns bought one off ebay for $30 was just as good always a good idea to have a spare. Find out if they sell the spray prime valve and inlet outlet valves .and a diaphragm if you have these that machine is gold..
@@sgpaint did you try it without the gun filter and hose filter.
Not bad piece of kit considering the price of the high end equipment, but I cannot believe what a mess everything is. Paint everywhere including all over you. I used to be an offshore sprayer using airless, I was also a vehicle refinisher using both types air and airless, the latter was used on HGV Trailers. My ocd would be doing overtime trying to cope with the state of the equipment and the place lol...
I cannot get mine to work. primes up no problem. pressures no problem but it will not fire out the standard nozzle.. absolutely nagged off with it..
chuck a pressure gauge on it then you know what psi your spray at 👍
Hi, i need some help. I bought this machine, but i'm struggling with it. I tried with water, and it works perfectly, but with the paint, does not work... Can you do a review with the inicial instructions, please!
Drop me a message on my Facebook page; S&G painting and decorating. I can talk you thought what to do. I will do a video but super busy at the mo so not for a while.
Would you recommend this for doing walls and cellings ?
Cellings for sure, walls if they are super smooth, just plastered.
Hi any chance you can attach a link to the attachments you got from amazon. Thank you
As soon as you type in tips you'll see its 4 blue tips... tbh I wouldn't really waste my money, best to just get higher end ones, make a huge difference.
Which tip u bought from amazone i bought this sprayer wanted to spray on interior woods
the tips are 215,315, 4...,5.... they come in a pack of 4 about £15.00
@@sgpaint with 215 what pressure u used was it full pressure
@@mojtabayousefi5184 just less than full, you just adjust the pressure till you get the correct pattern.
Thanks
I simply cannot unscrew the nuts that hold the trigger guard on, I need to do that to get the handle off to clean the filter. It's brand new. I don't why they fastened them on so tight, but it's utterly IMPOSSIBLE to budge either of them. Anyone else had this annoying problem?
I bought this today to paint fitted MDF panel wardrobes. Im guessing the standard tip is no good for the job ??
Any ideas on what size tip i should be using please??
Anybody there to help?
I'm on my new machine. Followed the instructions step by step and was spraying away and it just stopped on me.
When I turn it off and put it back to prime its working but the power just stopped on spray?
Water your paint down by 5/10%
Link to tips on Amazon
Cable tie on handle
Cowboy stuff you don't need it in a house , easy normal walls, it's only for awkward ceilings , pebble dash walls, and maybe if your doing loads of new builds
Its actually a wardrobe but hey, whatever floats your boat.
Cowboy stuff? Really? I’ve been an interior renovator for well over 25 years, I have a 100% rating, so it’s fair to say I’m no cowboy, and I routinely use airless spray. I would use HVLP for cabinets, but that’s just me, but this was a good video. I’d love to know where the cowboy comment comes from? If you’re in the trade, I can only assume you’re privy to something us mere mortals are unaware of!
sold out every were here
Hi all, could someone please help me, I have this sprayer, went to use it for the second time yesterday, I don't know what I have done wrong but it's leaking out before the tip, I have given am extra good clean at home buy what have I done wrong, please
help , in the middle of a job grr 😡😡
Check you have all the parts in place to the gun. Guard, tip and washer for the tip. Check all properly secure. Will do q video on this in due course.
What a mess for a day's work🤦
You are one messy sod 🤣
Mate, had to pull this unit apart, never that messy but thisnwas a life or death situation, for the sprayer at least 🤣
Too much bla bla no practical videos
Review bro.
How much water do u mix