TRANSMISSION NO SHIFTING, DON'T WASTE MONEY for new TCM.DTC P2720,
HTML-код
- Опубликовано: 29 ноя 2024
- Transmission electrical problem. Chevrolet Malibu 2013 model, drive start at 3rd gear and no shifting. Repair TCM without buying new parts,don't waste huge amount of money for new module and for programing.repair it to minimize the cost.
This video is on point and exactly how to fix these types of cars with this issue thank you so much for sharing
Thank you so much for showing the inner components!!!
😍😋
Great work. I had same issue. I replaced TCM. It came with a reprograming tool. It was $240. 2011 chevy malibu Ltz, 2.4 ecotec. Everyone said to get a new transmission haha. But if I would have seen your video I would have even more money. Great job 👏👏
Hi Dav Cav
I have 2010 chevy malibu
And have no reverse and forward only to second gear.
The code PO776 says it’s the solenoid issue.
Where did you get the TCM Hoping they have for my vehicle
Any help will be appreciated
Thanks in advance
@@AnguianoNoel I got my TCM from either autozone or advanced auto parts. I can't remember. Good luck my brother. 🙏
@@AnguianoNoel Hi did you find a solution? I have the same Problem.
@@MerisHllvc not yet the mecanic
Says transmission needs to rebuild
But haven’t taken it yet
Good luck.
Great! We can save some money, and also for the costumer we can minimize the cost of repair.
Salamat Kabayan. This has been very informative.
would like to know why you didnt ti tak the center an the last 2 solenoids to the left also what does the lift 2 solenoid do.
Really learned a lot from this video.
I would really like Bilal's input. I have 2015 Cadillac SRX only 60k miles that is shifting harshly/ vehicle jerking. I just took it out from the bodyshop after buying it at auction.
Anyway, when i checked the transmission fluid after already driving it 25 miles, it was low. I bought Dextron IV ATF to fill it but then decided to use Lucas Transmission Fix fluid instead - it is a lot thicker/ viscous than ATF. i used about 36 fl oz/ 1.2 liter ( 1.5 24 oz bottles). Now it is overfilled. The first two days the jerking was happening but it seemed less and less. Then I drove the car during the afternoon when it was really hot outside and it was jerking/ hard shifting a lot. Jerks at around 9 mph speed mostly such as when pulling in and out of parking lots
Have I damaged it my filling with extra and thicker fluid?
Do you think replacing solenoid like your video will fix it?
Is driving it around gonna damage it?
Okay sir first we need is to make scan or check for any DTC on your transmission.. possible problems was damage pressure switch membrane..need to scan so that we can pin point the exact problem..Lucas for transmission component slipping or overheating it will not fix the jerking and harsh shift
@@pjbandal I wish you were here in Dallas, brother Bilal. What is DCT? Since the harsh shift only happens when shifting 1to 2, you think changing solenoid may help?
عندي مشكل بلال في لابواط...فيتاس مايفوتوش
Awesome... How To Video. Thanks a bunch!!
My goodness, what a great video. I am wondering if I buy the solenoid pack only and replace that instead of the whole TCM if that would work and if i wouldn't need to reprogram it since i would keep the same computer?
Saludos desde Chihuahua México muy bien explicado, tengo un Malibú me marca p2723 el solenoide 5 me podrás desir cuál es
Lo solucionaste?
Brother another tcm Need same model or difference model no problem 😊
Good question, you need the same model if you replace tcm.
Excellent video just what I needed to see bravo 👏👏👏
Thank you for the good video. You. Did a good job?
After replacing the sensor did you have to reprogram the transmission
No need to reprogram, just make some adaptation.
my chevrolet cruze drives well when it's still cold, i get output speed sensor circuit and solenoid E problems when I check it after driving like 15 minutes, of course shifting problems as well, hot weather in Thailand yeah.
I’m having the exact same problem with my Chevy Malibu. Did you ever figure it out?
@@Noob.master6969my 2013 equinox does the same thing
@@Queeshandle have you had it inspected or anything? I recently had someone look at mine and got told it would need to be rebuilt. Im just wondering if a rebuild is necessary tho; I’m thinking what if it’s just the solenoids or the TCM that needs to be replaced
@@Noob.master6969 yes. I already got the transmission inspected and apparently looks good. Today, Im taking my car to an auto electrician to check wiring and stuff. They’re mostly sure that the TCM isn’t working right .
@@Queeshandle are you getting any engine codes? Also when you say your transmission got inspected, do you mean that they took everything apart and looked at it?
Hi thanks for the video. I have Cruze 2019 LS. Have same problem if I do the same will it work?
Yes it will work! First you need to make computer scan for the transmission module so it will lead us to right solenoid to replace.
@@pjbandal when i do the computer scan , should i do it while the car is moving and shifting??
Because i have a problem, from 4th to 3rd i feel like the car pushed backwards!
Good afternoon
I have a 2011 Equinox Ls engine 2.4 L think it has the same type of transmission
It only does 2 gears forward and reverse...
The scanner tells me that solenoid 3 is stuck but I already cleaned them and it continued the same.
My questions are :
Can I exchange the solenoids to see if it is a problem with the solenoids?
Clean them and change the oil but put them in the same place.
Check resistance of coils 4 ohms 123 567 and 18.5 ohms on 4
(the one in the center)
The other question is... If the tcm is damaged, can you send me the code for the stuck solenoid even though all the solenoids are fine?
Thank you in advance for your support and attention.
Great video Thank you Bilal 👍
great brother..
btw, how to solve dtc u0101 problem chevy cruze brother?🙏
Excellent video good job
I will subscribe your channel thank you very much...ive got idea i learn about transmission repair
You did a Good job there, I have a question tho, after you have changed the solenoid, did you
do some programming for it? Or the replaced solenoid has the same serial number for the other one?
Kabayan, nsa jeddah po ba kyo? May fb page po ba kyo sir?
Ung chevy ko sir may ship shock 2 and 3 Lalo n pag akyatan pag mag shift n sya low gear lakas ng kaldak
Check fluid level,try to make computer scan first
Hello
May you tell me how to remove the harness connector?
Yuppp no idea
hello, my equinox 2011 kicks me in reverse and could the 3rd and 5th be a solenoid?
What if I'm changing with new solenoid dose it needs to be in a certain order. FYI I have a Cruze 2013
Hallo sir
If the center/ the middle one is broken and have to replace, is must reprogram or not
Thank You
2015 chevy cruze sir Ilan resistant s pressure valve parehas lng b
No sir mag kaiba,line pressure nasa 10.5ohms to 11.5 ohms.the rest nasa 5.5-6.5 omhs..and depends also sa temperature
I have a Korean Chevrolot Cruze 2009 I have the same problem but my mechanic tells me to change full tcm and not solenoids, if I have to change solenoids should I need to buy specificily the solenoids of my year model car or any solenoids can be put, please let me know
If you change solenoid you can buy online ,the solenoid is the same specifications,only the tcm different calibration
Hello Bilal, i have two questions, which city you are in? Second one is after you replaced the solenoid did you do a programing for any software?
Bilal, can you tell how to find a solenoid fir 2015 cadillac srx ? The dealer doesn't sell it. Can you sell me one ?
Yes I can repair it,I'm here in asfan Jeddah..0555169801
@@pjbandal I just now saw that you replied, brother. Inshallah, I will give you a call... My 2015 Cadillac SRX kicks at 8 mph ( so going from 1st to 2nd gear) and now possibly developing issues at other speeds... I still was able to drive 12000+ miles since I started driving it...
Looking for some advice have a chervloret aveo LS 2011 gear not going higher in drive and I think it's stuck on 2or 3 automatic transmission...
First check the DTC do some scanning,check fluid viscosity
Hi dear,
My Malibu 2011 LT car (170k km) showing some issues regarding the Transmission gear. The R and D both would not engage and work propoly until I press the accelerator more to reach higher RPM then this would typically push the car to move.
The diagnostic shows the following code:
P0990:00 (Transmission Fluid Pressure (TFP) switch 5 circuit high voltage.
The transmission oil was replaced when it was 160k km (this time when the car showed R and D issues).
What can be the reason(s) behind this? Do you think the filter has to be replaced?
In your opinion, what is the best, to buy new Transmission gear or to fix this?
Cheers,
Ibrahim
Dear Ibrahim
Did you fix your issue? Cause I have same problem with my 011 malibu
Low fluid or clogged filter
@@requiem2803 Dear Hossam, I fixed the issue, it was the filter plus there was another internal filter which was broken as well. In addition to this, there was a small broken ring-like shape object. The car is working fine now. However, I recommend replacing the whole transmission gear if it is cheap in your region. Fixing it is not always successful and cost nearly as much the price of buying another (used but like new) gear.
@@pjbandal Hi Bilal, thanks for this reply. It was actually the main filter, plus another internal filter (was broken) with a ring-like shaped object was out of its place. The car is now running fine.
@@ibrahimyaseen8970 my car go backwards but not forward saying lost communication of the tcm what u think this could be ..?
P0796 Chevrolet Cruze 2013
Do you know what's this fault code problem
I just replace my transmission in my 2012 Chevy Cruze 1.8l and had it reprogram be for the reprogram it had 1,2,3 no 4,5,6 and reverse and after the reprogram now it have 3,4 and reverse no 1,2,5,6 the transmission I toke out was a 1st generation transmission and the one I put back in is a 2ed generation is there a difference in the to transmission's
Need some help bad no one here in my city don't know nothing or thay don't what to do there jobs
You replace also a new TCM solenoid?
Yes they have difference,1st gen has pressure switch ,2nd gen don't have pressure switch
Where can I buy a piece like that for a Chevy Malibu 2015 I have the same problem
I have cruze 2011 1.8, they said the tcm is gen 1, can i replace with tcm gen 2 ? More smooth shifting gear 1 to 2
Good video, mate!
Good evening sir, do you repair TCM of Chevy cruse 1.8L 2011 a/t ( stuck solenoid)
So the problem was a bad tcm or the selonoid?...
Malibu 2011 v6 3.6l code p0842 Tfps low input. After parking till car cool R work but D take some time to shift. After moving its ok the whole day till i park again night. Some time its work normally, Fluide changed with past owner, i think he put atf ||| instade of dexron vi, cause i found empty can in the trunk, do you think if i replaced the fluide the problem will be solve?thanks for prehelp 🙏
Great job
Hello sir, isa ako sa mga follower mo . Ngaun ako naman ang may issue sa car ko .. ang issue ay minsan delay shift sa drive or minsan nag i engage naman pero once na hinto ako sa stop light pag go na hindi na sia nag engage. Pero kapag nilagay ko sa drive 3 or 2 nag engage naman.. ok naman ang atf level ko. Anong solenoid po kelangan palitan. 2007 mitsu montero
Sir good Day tnx sa tanong,mas mabuti pa scan mo muna sir,base on your History na meron sya manual 2 or 3..baka na slip na Ang forward sprag..pa scan muna para di tau ma mis diagnose.
Hi dear
Very good work 👍
Did your workshop has branch in riyadh KSA or if you recomend to me any workshop in riyadh for transmission repairs?.
Mr. Bilal, where are you from, I am from Dammam, will you repair my Chevrolet Cruz 2017, i am having P0716 error code - Input Speed Sensor Performance and P07BF error code - Input Speed Sensor Circuit Low Voltage
Hi I have a 2011 Chevy Cruze LS. When I go in speed my RPMs starts to jump and makes a loud noise. Code P2714
Hi, have you fixed the issue, currently my car is also giving similar trouble, when car is cool it drives well, but after 50Km of drive it start jerks, mechanic is saying to change complete TCM & Valve body.
Please could you let me know how your transmission problem got solved ?
can I do this on equinox 2010
Is this the same TCM That’s in a 2014 sonic 1.8 ?
Its safe to check with a 12 v battery the stuck selenoid ?
Please respond , my car its a Malibu 2010 , thanks
Which number solenoid controls 3rd gear?
We're are u working in can u tell me the shop name and city?
Hi sir.
Fault code: P2714-00, Pressure control solenoid valve 4 stuck off, as showing in the computer scan.
They tried to relearn but after same issue is coming back.
As advice by the mechanic need to change the transmission which is too costly.
What can you advice with this issue?
Car is chevy cruze 2012 (1.8)
Yes if you replace transmission unit it's cost too much.if the fluid condition is good and no burnt smell,maybe you have a bad solenoid
sir anu problema nun chevy cruze ngpalit lng ng gear oil pumalya n yun transmission automatic
بلال ...سلام عليكم..عندي مشكل فلبواط
I have malibu 2009 3.5 v6 with transmisión problem so don't forwer ,,,,can bring me some info if can i fix the selenoids too and how can i do this
Good day sir! Saan po ang shop nyo?
mechanical friend. Excuse the inconvenience from here california greetings.
I have the code P0815 it is a GMC terrain 2010 v6 change the plates of the switches to the valvebody and finish the job but half counts that the manual speeds do not work for me and when the transmission oil heats up my transmission slips very little in first gear speed been in automatic and I have that code
help me please what could it be
i replace the TCM but gear not shifting , its stuck in shift number 3
Sir 6t70 transmission impala , after changing fluid , the car run but not shift , and the speedometer or kmph not functioning , ,pls give me some idea , thank you
Sir nagtangal ba kayo ng front cover Ng transmission?
@@pjbandal hindi po sir
Very good
Hi sir, are you still active sa YT channel, i just want to ask if same tcm solenoid lang ba cruze 2011 to 2016 and pwede rin ba malibu tcm solenoid sa cruze?
Are all of the yellow solenoids interchangeable? I realize the pattern of black yellow yellow shift yellow black black is important but I’m just wondering if the yellow in the 5th position and the yellow in the 3rd position could be switched and the function would still be the same
Yes it is interchangeable
Does this mean the black ones are interchangeable also? I ordered a whole new set and wanted to make sure it wasn't an issue before I put them in.
Thanks
Sorry, I meant the green ones
Thanks great video
Sir nasa Jeddah Pala kayo Baka may marecommend kayo na gumagawa Ng TCM dito sa Riyadh maraming salamat Sana mabasa nyo tnx.
Boy here in the Bahamas they make you by transmission dam save me some money
Kabayan kamusta po ask ko lang if parehas ba yung tcm ng 2011 chevy cruze 1.4 saka po 2012 cruze 1.8? Thanks in advance
Hai sir my car malibu 2013 today running 60 or 70 speed im slow car sliping gear movie acilator very slow running check caputer in put out put low wolteg. Code seeing another mechanic told chlenge gear wat problems sir
Ok ba sir ang tcm ng Chevrolet Cruze pero made OEM
This Must reprogram Or Not?
Thks
Not needed
Good day brother; I have 2014 2.5 L with a code U0101 lot communication with TCM. I don't know my way forward; I was thinking of buying the valve body with the TCM from the junkyard. Do you think I will have to reprogram the TCM to work with my transmission? Please help me
If you install use one no need programing as long it's the same model
@@pjbandal if my Chevy Malibu 2011 saying lost communication with the tcm my car it don't drive forward but reverse real good wat u think this could be nd it's saying tcm request
@@Trill89Atwgdid you fix this problem?
Mr. Bilal You llive in Riyadh Please reply
Please give me your address in Riyadh
I live in jeddah
Damn good video! About to try this!
Thank you Bilal.. a very useful video.. it looks like you work in Jeddah, can I get your address
Nice job
is there any solution for gearbox overheating ?
Hi where is ur garage location please
Please help me how can i diagnostic
Where is your shop located?
Hello sir we are located at asfan jeddah.. Smart town
What is ur shop name? How can I contact you?
@@Raad1982 Philippines star workshop, #1248,
Did you drain the transmission fluid first?
Yes need to drain the fluid.
Yes I drain
Changed one solenoid, car wont crank in park or neutral.
Would this be a bad MLP/ Transmission Range sensor/ Neutral Safety Switch?
Check your tcm if they have communication maybe you replace a bad tcm solenoid
Hi dear , where your location ?
after clean tge valve body of cruze and also all solonoid and change oil i reibstall everything.
engine is running, TCM not give any error but the car dont move in D or R.
only i got input speed reading but no output speed.
Can you give me any hint of cause of this problem?
Yes sir the input Speed sensor is connected to the torque converter when the engine is running the input drum is working..
Check the PRNDL it's working when you move the lever?check the fluid viscosity? smells burn?when you open the front cover of transmission you find anything debris?like crack plastic .. somotime the buffles was broken and clogged into filterand it will not engage in any gear
Sir dito ba kayo SA Riyadh may problema din Kasi ako TCM Chevrolet traverse 2010 Hindi sya Ng shishift lalo na malamig pa ang makina Sana mapansin nyo etong message KO gusto KO Sana ipagawa magkano ho Kaya tnx godbless.
Hello , I checked my car it is the same car in the video Malibu 2013 and the code was p075100 (TCM) and p77600 what is that mean ? Thanks in advance
Where are you ??
Dear Sir,
I have a 2007 gmc acadia. I feel hard shift only when downshift between 1 and 2 gear. Could pls assist me with this problem
Maybe you have a damage pressure switch, much better if you can bring to the workshop to make diagnose thru scantools..
Dude that suv is trash the dealer paid everyone off who owned that car my in laws had it
Excuse me what meaning of p0974
Shift Solenoid "A" Control Circuit High
My transmation is ( 6fhs ) chevy aveo
Specially after i change the transmission
It seems that you have a bad harness, check first the wire for ssA and resistance of the solenoid.if all was fine try to make reset the DTC and make adaptation.
Good job 👏 thanks
What about p2723 on an Malibu same year? Ever come across that?
I have no forward or reverse gears but that's the only code coming up
I have the same issues right now. Did you ever fix it?
Hi Bilal, good day, is this transmission the same as a 2010 Chevrolet Cruze, 1.8? Are the measurements the same for solonoids?
how to know if the computer TCM module, does not work correctly?, I appreciate your information greetings
What dod you figure out about your cruze i have the same model and mine wont shift above 4th gear
How much cost to repair this issue?
The cost is 1k riyals for the repair, 1month warranty.
Pretty cool
Appreciated
Are you filipino boss?
👍
Sadik, nasa jeddah po ba kayo?
i could sure use a lot LESS of the background noise. give the crew a 30 minute break when doing the next video
sir sa riyadh ka Po ba?
Jeddah sir
What is ur location? In KSA?
Asfan smart city Jeddah
Всем привет друзья. Это ерунда все равно надо будет менять
I have Chevrolet Cruze 2012; I had my Engine head and pistons replaced some time ago and after that I am facing transmission trouble. My car while going above 100 Km/h suddenly downshifts sometimes. Below 100 Km/h, it works good and above 100 Km/h the issue isn't happening always, only sometimes and after travelling more than 25 - 30 Km. Can you suggest what is the issue.
Can I have your mobile number to visit your shop.?
Hi, have you fixed the issue, currently my car is also giving similar trouble, when car is cool it drives well, but after 50Km of drive it start jerks, mechanic is saying to change complete TCM & Valve body.
Please could you let me know how your transmission problem got solved ?