I have rebuilt over 50 of Ph 65 .I have machined the armature on a lathe ,more then once on some hammers. Must clean out the gaps between the segments and bevel the edges to reduce sparking on start up. Half full the oil chamber with oil ,After extending the felt into the machine.This will extend the life. Also rotate the lower half 1/4 a turn sometimes .It will last longer.
Eine Drehbank ist nicht von Nöten. Eine Ständerbohrmaschine tut es auch. Mit unterschiedlichen Schleifpapier den Kollektor vorsichtig abschleifen. Isolation zwischen den Segmenten prüfen, fertig
Soy Miguel de Argentina. Respetuosamente te diría ya que desarmaste la hermosa maquina , creería que una buena limpieza por dentro no vendría nada mal.
It was opened and was dry without oil. why was it not filled with oil? Yet there is the level indicator and presence of oil. In my opinion it will not work for a long time without oil. However it could have been cleaned and greased better.As for the disassembly, repair and reassembly, I can say that a good job was done, even if the oil pan gasket was missing.
Buen trabajo felicidades por tan buen video soy de República Dominicana me interesa saber donde comprar el rotol ya que reparó esto tiempo de retro martillo o taladro martillo cómo le dicen aquí
Это не ремонт . А неуважение к себе и клиенту. Как можно оставить старую смазку не промыть инструмент не диагностировать состояние подшипников ? Мастер 3 сорт . Таких полно в сервисных центров. Когда им говорят промыть посмотреть что заменить надо . Они отвечают если делать как ты говоришь клиент долгие годы не появиться
The hammer 🔨 end wasn't pulled down properly because it needs to be thoroughly cleaned & the parts right at the end in front of the striker needs to be inspected for wear because it's the part which strikes the bit which slips into the toolholder.which needs to be.unscrewed to inspect the striker. I didn't see the O rings get replaced which should be done every time the machine is overhauled & no Hitachi hammer grease was used meaning that the machine won't Hammer, it's a liquidy yellow grease which is used to lubricate the O rings, striker & piston as pneumatic pressure is created in the piston & striker assembly,the striker also needs to be checked for wear & damage,it won't Hammer with worn O rings. Makita have the same grease as Hitachi do for their jackhammers & rotary hammers !
let him be..these are third world countries man...its a miracle that they have electric screwdrivers....they know crap about jackhammers,bearings etc...just let it be..:)))
Ну заменил подшипник на якоре, хотя если ремонтируешь, то лучше менять все. Потом, статор желательно было прочистить растворителем и пропитать лаком. Да и корпус надо было вымыть, а то смазку в это дерьмо ложить, меня бы сожрал мастер на работе за такой труд.
H hmm ghh&hhhVivi hjhhhbghigh&hg)hhhHIV hijhhghhhhh&big if high high jjghh off&)big hhhhhogh of jihhoohhhh&ghhhigh hhghoigbuooo hihhhh&)hhhuhhhuh JK jbhiihh if hug) h if I'm going to ugh if I by iuhhuhhh if h) g) uhhh UFOhhhhhu&go jog and h to get a hold 👆 the he if ghb&hhIHOP ghgighbihghhghhhhhg) hhh KFC go jog on a highlight of uhhhhhhgbh huff I had the chance he'll ghgh8uuuhhhhg) buhbhghigihiiibhhibg hi
porque tirou o extactor e voltou a montar?...trabalho nojento montar a máquina com toda a sujidade interior sem lavar todas as peças.>e por fim meteu as mesmas escovas num enduzino novo.
Armature >> it is basically the heart of the tools, and he didn't actually repair it, he just bought a new one and replace it with the old one even though he might have fixed the old hitachi one by rewinding the armature, if necessary of course, or just cleaning the commutator and testing it for any possible power shortage. this is coming from someone who is not a repair guy, but learnt something from the internet, >> Good manufactured armatures should never be replaced by cheap ones, Yes, the operation is annoying but 100% worth it, and I'd pay anything for someone who is not taking the easier way around and actually taking the extra miles to fix the original great armature to its normal state.
KO ZNA - ZNA , A KO NEZNA AKO IMA VOLJE DA I ON NAUCI DA I SAM TAKO ZNA POTREBNO JE SAMO JEDNA STVAR A TO JE DA IMA JAKU VOLJU DA TO NAUCI OD NEKOG KOJI VEC ZNA. NISTA PROSTIJE OD TOGA NEMA. AKO COVEK NEMA VOLJE DA SE NECEMU NAUCI I DA MU PRED NJEGOVIM OCIMA VASKRSNES MRTVACA - NE POMAZE NISTA !!!
muy buen trabajo con mucha presicion y en poco tempo te felicito buen talento grasias por compartirlo..chao.
I love the commentary where he explains everything that he's doing in more details.
I have rebuilt over 50 of Ph 65 .I have machined the armature on a lathe ,more then once on some hammers. Must clean out the gaps between the segments and bevel the edges to reduce sparking on start up. Half full the oil chamber with oil ,After extending the felt into the machine.This will extend the life. Also rotate the lower half 1/4 a turn sometimes .It will last longer.
Eine Drehbank ist nicht von Nöten. Eine Ständerbohrmaschine tut es auch. Mit unterschiedlichen Schleifpapier den Kollektor vorsichtig abschleifen. Isolation zwischen den Segmenten prüfen, fertig
ياخويا بارك الله فيك احييك من الجزائر 🇩🇿
Soy Miguel de Argentina. Respetuosamente te diría ya que desarmaste la hermosa maquina , creería que una buena limpieza por dentro no vendría nada mal.
Verdad, se quedo el trabajo por la metad.
It was opened and was dry without oil. why was it not filled with oil? Yet there is the level indicator and presence of oil. In my opinion it will not work for a long time without oil. However it could have been cleaned and greased better.As for the disassembly, repair and reassembly, I can say that a good job was done, even if the oil pan gasket was missing.
Good disassembly of the tool
Good replacement of the armature.
کارت درست بود، آفرین خسته نباشی
wow !!! excelente amigo...saludos desde Venezuela y Colombia mi parce !!! Good work man...regards from Venezuela and Colombia my parceroooooo !!!
L by
Good that you were able to get spare parts for this old tool. Often parts are just not available, so repair is not possible.
Mantab ladde boss ku ilmux
Kardeşim merhaba işiniz çok güzel ama matkabı temizlemeden olmaz
Nice restore
Good job five star super repair
Buen trabajo felicidades por tan buen video soy de República Dominicana me interesa saber donde comprar el rotol ya que reparó esto tiempo de retro martillo o taladro martillo cómo le dicen aquí
Superb bro..I'm also a service engineer for power tools.....in India... learned a good techniques from you......
I come from China
Yes, isne spring kitne ache se lagayi
hacerle una limpieza por dentro y por fuera, quedaría un trabajo mas profesional
Это не ремонт . А неуважение к себе и клиенту. Как можно оставить старую смазку не промыть инструмент не диагностировать состояние подшипников ? Мастер 3 сорт . Таких полно в сервисных центров. Когда им говорят промыть посмотреть что заменить надо . Они отвечают если делать как ты говоришь клиент долгие годы не появиться
آفرین خوب بود
THANKS FOR YOUR SHARING SIR
Veri good..👍👍👍👍
Good job 👍 I
Good work,well worth learning
thank you😘😘😘
Great job, let more people learn knowledge
thank you😘😘😘
Ficou bom só daria para dar uma limpada melhor
Desarma completa esa maquina pero no limpia nada🤔
The hammer 🔨 end wasn't pulled down properly because it needs to be thoroughly cleaned & the parts right at the end in front of the striker needs to be inspected for wear because it's the part which strikes the bit which slips into the toolholder.which needs to be.unscrewed to inspect the striker.
I didn't see the O rings get replaced which should be done every time the machine is overhauled & no Hitachi hammer grease was used meaning that the machine won't Hammer, it's a liquidy yellow grease which is used to lubricate the O rings, striker & piston as pneumatic pressure is created in the piston & striker assembly,the striker also needs to be checked for wear & damage,it won't Hammer with worn O rings.
Makita have the same grease as Hitachi do for their jackhammers & rotary hammers !
let him be..these are third world countries man...its a miracle that they have electric screwdrivers....they know crap about jackhammers,bearings etc...just let it be..:)))
Hello, great video. I need to fix mine. Can you please tell me where I can get the replacement parts?
Very good video
well worth learning
Ну заменил подшипник на якоре, хотя если ремонтируешь, то лучше менять все. Потом, статор желательно было прочистить растворителем и пропитать лаком. Да и корпус надо было вымыть, а то смазку в это дерьмо ложить, меня бы сожрал мастер на работе за такой труд.
Подшипник как раз остался старый он поменял полностью ротор....
You repair perfect,confirm many like from all people
H hmm ghh&hhhVivi hjhhhbghigh&hg)hhhHIV hijhhghhhhh&big if high high jjghh off&)big hhhhhogh of jihhoohhhh&ghhhigh hhghoigbuooo hihhhh&)hhhuhhhuh JK jbhiihh if hug) h if I'm going to ugh if I by iuhhuhhh if h) g) uhhh UFOhhhhhu&go jog and h to get a hold 👆 the he if ghb&hhIHOP ghgighbihghhghhhhhg) hhh KFC go jog on a highlight of uhhhhhhgbh huff I had the chance he'll ghgh8uuuhhhhg) buhbhghigihiiibhhibg hi
Gghhhhh go Ohio hhhigggbhbhbihhghibh ouch hhbghhggggg
&i ugh gbggggb icon GB to him FBI good morning hi
I unit gghb gig gg Ivy hghgbbgggbiigbb
Go iib&gghbigg8gbguy gbgi giving hivigiggg
Why you didn't clean inside ,?
Wah angel lek
Hello from iraq well done do you changed armicher
Vite et bien merci
donde puedo conseguir la armdura para este tipo de modelo gracias
Nice video
Buenos dia donde están ustedes ubicado tengo un Router Hitachi quiero Saber si puedo salvarlo tienes problema con la masa el colector ha colapsado
Good👌
Tenho uma parecida com essa só que o óleo tava acabando e eu coloquei óleo de motor de carro não sei se é apropriado
porque tirou o extactor e voltou a montar?...trabalho nojento montar a máquina com toda a sujidade interior sem lavar todas as peças.>e por fim meteu as mesmas escovas num enduzino novo.
What’s the point in putting grease on something you haven’t cleaned up
Este es un trabajo sucio,no se limpio, no se reemplazaron los rodamientos .
I want to see much of broken armature worked on
You just replace it, what repaint you have done?
Sabe desmontar e montar como profissional agora deveria fazer uma limpeza bem feita e depois coloca graxa nova
Concordo plenamente, limpeza zero nossa
@@py6jfvjdovaleferreiradoval177 afinal ele trocou o induzido ou só limpeza
It’s all good but I would clean all parts and grease it before put it together
Hi
Hi
Yes, how I can help you?
Sing penting isoh urip neh
@@dimpildimzy7997 I have no idea what you just committed
Need to put an lubricant oil in it,also there is an oil reader(round transparent glass)
Tengo uno lo preste y me le quemaron la masa soy de Santiago Rep.Dm. Donde puedo conseguir la masa
It could have been thoroughly cleaned with a pressure washer
Thanks for
Good work
Nice
Musica del 70clasica
He should clean all parts. Need grease and oil 🤔🤔
Show, muito bom!!!!
U should also clean up the machine.
good
Tempt kerja ku punya hitachi yg klH roda gigi rotornya .bgmn sulusinya
Good
good jab
Ok felicitar
Très bien un bon électricien
Your not repair the armateur? You change new... Bad cheetha...
ทุ่น amature ซ่อมยังไง
Hultimas notisiasdel tesoro hescondidode Mauricio montij
Like 👍👨🎓💐
Statorul văd ca este bun .Eu vreau sa vad cum se repara colectorul ? Asta i important .
Sustituye el rotor. No lo repara.
Why you no clean before install..change new grease,o ring piston new
جيرة الله يسلمك يا قلبي انتي والله ما عندي
👍👍👍👍🙏🙏🙏
untuk jek hmer mrek boss,,yg 3,,jalan gmna bozzz
Its a repalcement only i though you gona repaire the actual armeture
H
bhayo he husiyar
Dónde puedo conseguir la armadura gracias
anrih
anrih
b
It's good job but why don't you all wash it poriley and fix then you.can be a professional so start do'g a clean Jon txs
ทุ่น amature
Bhai is Saman kahan Milta hai iska repair karne wala
ازمدارات سیم پیجی موتور پخش کنید
Ok
Veo que no sopletea nada toda sucia la vuelve a tapar .
What is the name of the thing that you change?
Armature >> it is basically the heart of the tools, and he didn't actually repair it, he just bought a new one and replace it with the old one even though he might have fixed the old hitachi one by rewinding the armature, if necessary of course, or just cleaning the commutator and testing it for any possible power shortage.
this is coming from someone who is not a repair guy, but learnt something from the internet, >> Good manufactured armatures should never be replaced by cheap ones, Yes, the operation is annoying but 100% worth it, and I'd pay anything for someone who is not taking the easier way around and actually taking the extra miles to fix the original great armature to its normal state.
Angker diganti anyar
Un trabajo sucio que no limpia nada un restaurador no hace un trabajo sucio
Porqué no limpiaste no tenias un poco de decoro
Kolektörü ne zaman temizledin, göster.
Yenisiyle değiştirdi.
how much the armature cost? give me the link thank you
Qeeei ieieeiieeoeee eiieoieiieriiwiyeieeiieowwieieeorieiwieetppeqeeiwooqeiuiieeryoieeeeeqeiiiereieeiiiewiwro
Armature replacement
KO ZNA - ZNA , A KO NEZNA AKO IMA VOLJE DA I ON NAUCI DA I SAM TAKO ZNA POTREBNO JE SAMO JEDNA STVAR A TO JE DA IMA JAKU VOLJU DA TO NAUCI OD NEKOG KOJI VEC ZNA. NISTA PROSTIJE OD TOGA NEMA. AKO COVEK NEMA VOLJE DA SE NECEMU NAUCI I DA MU PRED NJEGOVIM OCIMA VASKRSNES MRTVACA - NE POMAZE NISTA !!!
Job dila do yr mujse ye sb km aat ha all
Like👍
Cho em hoi cu gop loai 9 rang ban bao nhieu anh oi
لو غاسل الكفر
Wes
😂
How much u restore mine
ja que desmontou porque nao limpar
Te falto reemplazar el rodamiento por uno nuevo, no valen mucho.
Mi Router Hitachi es de los viejos si ustedes tienen whasap de dejan en número asi le envió imagen quísa tengan esa masa
What is the blue paste you used at 11:20?
高温黄油,蓝色的
Grease
Iso mbalekne pora wingko boss
R