DOE Van-dalised Ford Transit Back Brake And seal's Part 10
HTML-код
- Опубликовано: 6 янв 2024
- business and permissions inquires bodgitandleggit@gmail.com
If an Bodgit And Leggit Garage, Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE:
/ bodgitandleggitgarage
paypal.me/bodgitnleggit
ko-fi.com/bodgitandleggitgarage
/ bodgitandleggitgarage
bodgit and leggit garage
tips and tricks inside this video hopefully help you
don't forget get your hands dirty
www.bodgitandleggitgarage.com/
bodgitandleggitforum.editboard...
/ bodgitandleggitgarage
/ bodgitandleggitgarage
Disclaimer:
Due to factors beyond the control of Bodgit And Leggit Garage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Bodgit And Leggit Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Bodgit And Leggit Garage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Bodgit And Leggit Garage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained 
Авто/Мото
Just so everyone knows I keep getting this question. So many times no I do not have a new garage. No this is not my garage I am still doing mobile work
I've always had reasonable success with one of those little impact drivers but each to their own
This was a good job- as I could see from my arm chair 😁
After al, it‘s a Tran-shit.
Those torque wrenches are the ones used in coach / lorry garages to tighten the wheel nuts.
Great series of Videos. Really great content and no nonsense way of explaining the processes. Thanks.
great to see you are hard at it as if you are anything else and that was the best way of getting those little bolts out i do that but i have also welded a bit of metal to the bolt and then just turned it and put new ones back with a bit of copper greas on the back of the heads ,keep warm as it is going to get colder as if you needed telling. thanks for the video
One of the hardest mechanic jobs in the world has been a mobile mechanic
LOL you had me shouting ABS ring but hay job well done
Given the good work you have done and the money you have spent, , Shame the cost of the diff oil you mentioned was too expensive, I would have wanted to replace it while I was there, You was well set up and good access to do so
What was a concern for me was they said the oil seals were gone but on removal of the disc all was dry.. looking at the video the rear shockers looked very wet as if they were shot....
Hi Leon, do you ever sharpen your drill bits? If so it would be good topic for a video 😉
@ 3:15 3/8" torque wrench? Did you mean to say 3/4" Great vid BTW
Did the transit not have back plates to protect the disks?
Impact driver would have removed the disc screws
How come no Greece on the bearings
The amount of work you’ve done on that van it would’ve been cheaper to buy a new one
Why did the video at 28.30 remind me of the dentist.
here in UK. DVSA standards is not a fail on those disc's. They have to be SERIOUSLY corroded and about to fail.
hi ,there I be so grateful if you could answer me this question,,,,,,, I have a 150l air compressor ,I connect it to the socket and the 13 amp fuse keeps blowing ,,,its says on the air compressor ...16amp 250v,,,should I get a 30 amp consumer fuse and another one at 16 amps for the garage ? thank you if you could help .....the 13 amps is a normal fuse
Hi mate I would get a heavier duty cable and a 16 amp breaker But what you need to check is your capacitor that's in the compressor that could be going bad, causing a lot higher start up ambridge
hi bro thank you for your reply ....I have connected a 16 amp to the breaker and also I have a 12mm cable on it ,,and on the garage I have just a normal socket the ones you can plug microwaves or other things on ,lets say 240v 13 amp socket...when I plug the compressor on it the fuse from the mains keeps drooping ,,,so I dont know what is wrong with it .thankx Carlos
@@bodgitandleggitgarage
Nothing wrong at all with that disc
That is how, they would do this Job in Africa though they probably wouldn't have a Vehicle Lift..! 😇😇
I would do it by paying someone else to do it
No Power Tools, Please..! Remember you are doing a Script for The Mechanics in Africa..!
Just replace the impact wrench by a long pipe and ignore torque recommendations - just make it tight.