You made a big mistake when mounting the bracket. You should have mounted the bracket fully to the bottom of the case. You needed to remove one more space in back. This way the card would have rested on the pads, which were included. There woould have been no need for the support bracket that you added.
Hello, thanks for the video! At 0:55 you can see a hole in the bracket, on the right side next to the mesh, could you measure and tell me how big that whole is in mm? I want to know what kind of cables i could fit trough there :)
In the begining you had 1 slot empty on the bottom. Can i put this bracket like that and still have a access to the pcie x1. I have a netword card in it.
Do these adapters make the data transfer slower? I mean it cant make the input faster? Maybe these create a bit of input delay, I wanna use one, but that thought just bothers me ahh
There are no GPUs yet that support PCIe 5.0. both new AMD 7000 and Nvidia 4000 series use 4.0. So no point to wait, just dubbel check that it's not a 3.0 riser.
can i use this to mount a Capture card the elgato 4k60 . My new graphics card takes up the whole motherboard and covers my second pcei slot so i have no pcei slot for the Capture card to go in. But i was thinking of doing this for it. Please let me know what you think!
any issues with it? I have one coming in tomorrow for a build a guy is grabbing this week. 3080 ftw3 exhaust is a little too close to the glass, so a card that already runs hot was running too hot n loud for my liking. Temps will probably drop pretty close to side panel off in my situation.
My video card is a Galax 3060 Ti 8gb, but I put a PCI 4.0 cable to make it vertical, and in GPU-Z it says it's working in 3.0, I don't know why it's like that, since it's 4.0, no should it be showing 4.0?
You made a big mistake when mounting the bracket. You should have mounted the bracket fully to the bottom of the case. You needed to remove one more space in back. This way the card would have rested on the pads, which were included. There woould have been no need for the support bracket that you added.
Also would remove the strain on the cable and slot due to the cable being bunched up more.
Thank you for the informative video!
Also. Having the cooling block be the highest point means air will gather there if you get or have any which isn't good for your cpu
Thanks for showing the whole process!
Do you think normal sized fans fit directly under the gpu ?
Nice Job. Which case are you using? model?
Cooler master TD300 MESH
Hello, thanks for the video! At 0:55 you can see a hole in the bracket, on the right side next to the mesh, could you measure and tell me how big that whole is in mm? I want to know what kind of cables i could fit trough there :)
I have the same bracket, it's about 25mm x 14mm. Enough for HDMI and DP cables to pass through
What is the thing you added to the end of the gfx card to hold it in place? Coolermaster something....
GPU holder
3:08 these 3 screws, where exactly are they going in? are they simply making pressure holding on the case?
Casing PCIE Slot , take out your casing PCIE Slot screw then replace it or use back same screw.
Thanks for the video, helped me alot.
thanks for watching
You should've mounted the watercooler with the hoses on the top, JaysTwoCents has a video on this.
Hi, you're right....in the beginning I plan mounted there.however,my Ram blocked there...my RAM too height..lol
Current setup is better than with hoses on top. As per jay and GN
Would it be possible to place the support one slot above to be able to use the last pci slot?
can , if your RAM no big as my one... and depend on what casing you use...... anywhere, my case can't
@@LeeCheemin 😁Thanx
In the begining you had 1 slot empty on the bottom. Can i put this bracket like that and still have a access to the pcie x1. I have a netword card in it.
I think depend your casing… for mine can’t
Yes, its possible, i have a lian li lancool 205 i had to cut a few of the slots but i still have clearance for my wifi card at the bottom slot.
Será que um Air Cooler Mugen 5 ia caber aí no lugar do water cooler?
How many cm height ?
Do these adapters make the data transfer slower?
I mean it cant make the input faster? Maybe these create a bit of input delay, I wanna use one, but that thought just bothers me ahh
Should be no … so far so good
Nice Man,
Parabéns!
Thanks
I want to buy this but is it gonna work with Rtx 4080 ?
As long as PCIE 4.0
Do you leave it open do you put the front panel on it?
Nope
I see you got a support. How bad did it sag?
I got to get a vert mount that will fit 4090 and active back plate.
I put the support because last time i yet buy the vert mount… after get vert mount I think no need support…
If it's installed correctly there is no sag as it rests on the bottom of the case.
if my motherboard has PCIE5.0 would it convert the video still or do i have to wait untill a 5.0 riser becomes a thing
Better wait for PCIE5.0
Yes Pcie 5.0x16 slots are backwards compatible. No worries you can use a gen 4 riser. I have this in my rig.
There are no GPUs yet that support PCIe 5.0. both new AMD 7000 and Nvidia 4000 series use 4.0. So no point to wait, just dubbel check that it's not a 3.0 riser.
can i use this to mount a Capture card the elgato 4k60 . My new graphics card takes up the whole motherboard and covers my second pcei slot so i have no pcei slot for the Capture card to go in. But i was thinking of doing this for it. Please let me know what you think!
This Bracket need use 7 slot, if your casing have space maybe can
it will fit into any computer case that is in atx standard?
As long as your case have 7 expansion slot ( PCIE slot)
300mm or 220mm? G360A case
Cooler master Td 500 mesh
Friend does need to change something at bios before installation?
No need
This soporte rtx 4090?
Yes… as long as PCIE3.0 and 4.0
What case is it
Cooler Master TD500 Mesh
Is it compatible with amd rx7600 xt
@@sngediting661 as long as compatible with PCIE-4 or 3…tq
you left 2 top slots empty and cover it. can i do the same but leave those 2 at bottom and keep 2 fans under the gpu ?
thanks
Depend your casing and PCIE Slot on MOBO.. for mine case, I can’t do that because not enough space
@@LeeCheemin has 7 slot. nox hummer mc pro(gpu is msi 1070ti). wanted to keep 2 bottom fans
Is it suitable for the new 4070 ti?
I think as long as suuport PCI-E 4.0 is will suitable... however suggest you go official website ask them.. tq
Is this working with a 4090?
Yes
your case is CM TD500 mesh?
yes
@@LeeCheemin oh nice .. thanks
CPU AiO, air bubbles? 4:46 No problem, ha?
Got? So far no problem…
any issues with it? I have one coming in tomorrow for a build a guy is grabbing this week. 3080 ftw3 exhaust is a little too close to the glass, so a card that already runs hot was running too hot n loud for my liking. Temps will probably drop pretty close to side panel off in my situation.
I doesn’t see any issue for mine
@@LeeCheemin awesome thanks! I figured phanteks would be good
would this work with a 4090 (GIGABYTE Gaming )?
I think as long as suuport PCI-E 4.0 is will suitable... however suggest you go official website ask them.. tq
Can I use this with the neo cube?
Should be can, as long as have 7 PCIE slot
That AIO is mounted wrong
Can you explain why its wrong? Its correctly mounted , i think you misunderstood the videos of aio mounting like everyone else
thanks for the review
Thanks
hello... is compatible for all cases?
As long as mid tower above
that was painful watching him install it lol
Great. The back of the GPU is radiating heat towards the internals of the case...
Uhh no
Negligible amounts
Your radiator is upside down, your going to wear out the pump.
i followed the radiator official website video installation guide...
Gamers Nexus did a video on this. Tubes down is the most optimum orientation.
xin chào bạn làm ơn cho tôi được biết cách phân biệt loại 4.0 và 3.0
Cable there got write...or ask before buy
super. this is well eiting!
My video card is a Galax 3060 Ti 8gb, but I put a PCI 4.0 cable to make it vertical, and in GPU-Z it says it's working in 3.0, I don't know why it's like that, since it's 4.0, no should it be showing 4.0?
My GPU Z show PCIE 4… your mobo is pcie 4? Did you put in correct slot ?
Nice Man
You should probably flip your radiator because over time you will get air bubbles in your tubes
Thanks for advised…Actually I follow the video share by the radiator brand installed ..
@@LeeCheemin It’s fine the way it is. The pump is lower then the top of the radiator, no need to worry about airbubbles.
This is the correct way lmao
Не вижу смысла горячий воздух от вк направлять в сторону мамки, ради красоты?
that's why need more fan to direct the hot air out at the top...
what a crap..... engineers - stop drinking vodka :D:D:D
this is horizontal tho
Any idea where to get a 4 slot vertical mount? I have a Corsair Crystal 280x case, it's a mATX case
You may check Lian Li O11D …
Надо было вид сзади показать а не вентиляторами хвастаться