Its good to test an IGBT, but you cant transfer 5A or 10A! or the IGBT will burn after Overheating, specialy if you have 60V input and 12V output!!! 60-12=48V , 48V*10A= 480Watt that means you produce 480Watt Heat in a 290Watt IGBT, and the Consumer get just 12V*10A = 120Watt :D Use a PWM circuit as a driver for IGBT, Mosfet, SCR ...
مجهود رائع .عندى سؤال من فضلك .هل يمكن ان ادخل تيار شدته ٧٠ امبير وجهد ١٢ فولت ؟ بحيث يعطينى تيار شدته على الاقل ٢٠ امبير وجهد ٢٤ فولت؟ ارجو الاجابة من فضل او من اى احد من الاخوة المتخصصين او الدارسين . ولك جزيل الشكر ولجميع الاخوة المشاهدين.
HI If I want to use 240 amps instead of 40 amps IGBT, what models should I replace the other parts with, and also can the amps be increased to 400 amps by using 2 240 AMP IGBT
@@rudilunk1555 Please, build it for yourself and make a RUclips video of your test. RUclips videos of things blowing up or catching fire are always popular.
No. You might make a version with a 20 volt input and a 13 volt output, but at 20 amps the transistor will burn up. This sort of circuit CANNOT produce an output greater than the input, and for this particular version the input must be at least 7 volts more than the output to work reliably for the transistor specified.
So the voltage that you are putting into the circuit that you did a video on is ran through a bridge rectifier & filter capacitor, then into the circuit you show ?
Hey all of u guys its just entertainment purpose dont try time and money waste i allredy try this but the IGBT HEATSINK WAS too hot and burned so its not for use long run without IC thats it.
No, no and no. Well, OK, maybe. You would need a much higher value (resistance and power) potentiometer, and a MUCH bigger heatsink. Bigger wires, too. Keep in mind that as built this circuit will not handle 60 A even at lower votage.
This circuit isn't even a voltage regulator in any normal sense of the term. All it is is a voltage "follower." The output voltage will vary with varying input voltage and with varying load. It is more or less the equivalent of a an adjustable power resistor (rheostat).
...habría que adaptar el divisor resistivo a la Vin para obtener Vge adecuada. ...the resistive divider would have to be adapted to the Vin to obtain adequate Vge.
@@MQVlogspk ...este circuito no sirve como controlador de carga solar. Para ese fin te hace falta un MPPT. @MQVlogspk ...this circuit does not serve as a solar charge controller. For that purpose you need an MPPT.
Si necesita solo 15V no lo debe alimentar con 60V porque la diferencia la tiene que absorber el IBJT que solo soporta 300W a 25°C. If you only need 15V, you should not power it with 60V because the difference has to be absorbed by the IBJT, which only supports 300W at 25°C.
Of course, if you use a 60 volt output, what's the point of all this fuss? Otherwise why not show it? I need to stop wasting time on these useless sites
building a model that shows the way of connecting household appliances can you show how to do and please help me i need for school project please please please ✨✨✨🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
Perfect! wanna see test 40A! 🤣🤣🤣
at 40 amps, the author of the video will have to call the fire department. 🤣
Perfect! wanna see test 40A!
at 10 amps there will be fire and fireworks. 🤣
لاكن بلحمل اعتقد تحتاج لعدة مقاومات واناكريت يغذي حسب الحمل كي لا ينزل الفولت
Its good to test an IGBT, but you cant transfer 5A or 10A! or the IGBT will burn after Overheating, specialy if you have 60V input and 12V output!!! 60-12=48V , 48V*10A= 480Watt that means you produce 480Watt Heat in a 290Watt IGBT, and the Consumer get just 12V*10A = 120Watt :D
Use a PWM circuit as a driver for IGBT, Mosfet, SCR ...
Like The Videos, but replying to questions would be a plus to your viewers !
tq.
Thanks for watching my friend 🙂
Faltou so vereficar a queda de tensao que as lampadas provocaram quando estavam ligadas
Which voltage is given in the input -?220 ac and dc
Can we parallel this IGBT for higher capacity the Amperes ?
INPUT VOLTAGE PLS and why would you need 60v to charge a 3,7 volt battery at 40 A
مجهود رائع .عندى سؤال من فضلك .هل يمكن ان ادخل تيار شدته ٧٠ امبير وجهد ١٢ فولت ؟ بحيث يعطينى تيار شدته على الاقل ٢٠ امبير وجهد ٢٤ فولت؟ ارجو الاجابة من فضل او من اى احد من الاخوة المتخصصين او الدارسين . ولك جزيل الشكر ولجميع الاخوة المشاهدين.
Which MOSFET or igbt good for 12 v 20a please reply 😊
Thank u a lot .
you are jenius brooooo!!!!!!!!!!!
Thanks for watching 👍
so good!!!!!😁😁😁😁👍👍👍👍💯💯💯💯
Thank you so much 😀
The amount of current entering and connecting the rotation sensor to the fan changes with temperature
Please full connection diagram. Power transformer, bridge diodes, regulator filter etc
Buddy, it’s hopeless. The guy wouldn’t respond. All you gotta do is test and experiment by yourself.
TRY AND ERROR IS BETTER.. BUT NEED TO LEARN FROM PEOPLE WITH EXPERIENCE. FACTOR MAY CAUSE COMPONENT LOSS OR EXPLOSION
Cual es voltaje entrada
Good idea, does it really regulate, I don't see a feedback circuit?
Good website for buying electronic components in india
Buy from electroncomponents.com
@@CreativeTechos thank you bro
Apa kh ini arus dc om
Sir can i use mosfet fdb6030bl for regulator because i have many mosfet fdb6030bl 🤐
HI If I want to use 240 amps instead of 40 amps IGBT, what models should I replace the other parts with, and also can the amps be increased to 400 amps by using 2 240 AMP IGBT
Add more igbt 3 or 4
SHOW DE BOLA MEU BROTHER, MANDOU BEM...
You most certainly cannot make a 0 - 60 volt source (not regulator) at 40 amps with this circuit, especially using a puny litlle heat sink like that.
Yes he can,,,hmmm, make a smoke machine out of it :)
60V/40A son valores max. no simultáneos. No se puede superar los 300 W a Tamb. 25°C.
Bullshit😅
@@rudilunk1555 Please, build it for yourself and make a RUclips video of your test.
RUclips videos of things blowing up or catching fire are always popular.
Can i used it controlled motor 775?
Can this circuit be with a 13v input with a 16v output with a 20a load?
No. You might make a version with a 20 volt input and a 13 volt output, but at 20 amps the transistor will burn up. This sort of circuit CANNOT produce an output greater than the input, and for this particular version the input must be at least 7 volts more than the output to work reliably for the transistor specified.
Bhai agar 40n60 igbt transistor naa mile to iski jagah koi dusra kon sa use kr sakte hai
Please reply
What is the source and power supply connected to your device for it to work? Thank you.
La fuente de alimentación debe entregar 60V/40A si desea alcanzar esos valores pero puede usar otra de menor potencia.
Good voltage regulation?
what is the input voltage range?
3.7v to 12v can be supplied as input
Can this type of V.R be used to charge a car battery? Say 90 amp?
Dear sir would load 36 v 40 a load d c motor or welding purpose.
Very good 😊
Thanks for watching
Hello
How many DC volts are needed as input?
Input 60 volts and output variable
So the voltage that you are putting into the circuit that you did a video on is ran through a bridge rectifier & filter capacitor, then into the circuit you show ?
Qual a voltagem de entrada
60v dc max
اخي كم جهد الدخول في الدائره
Hey all of u guys its just entertainment purpose dont try time and money waste i allredy try this but the IGBT HEATSINK WAS too hot and burned so its not for use long run without IC thats it.
Hello bro. Excellent. Can I connect 9v to get 4.5 and 6 volt?. Please reply.
Yes, absolutely you can use it to get your desired voltage.
wow amazing!!!!!!!!!!
👍
Nice
Y el potenciómetro se calienta
How much is the input voltage
Maximum 60v dc
bagaimn kl utk daya yg saya gunakn sampai 90 volt mr... (how can do it to that 90volt up my mine ..should are you can do to me mr...regard from me )
Can I use GT25Q101 ?
He hecho uno igual pero cuando conecto la carga el voltaje cae a la mitad
input voltage is?
Have any other circuit for dual power supply
Can i give input supply 100v 30 amp in this circuit ?
5:48
No, no and no. Well, OK, maybe. You would need a much higher value (resistance and power) potentiometer, and a MUCH bigger heatsink. Bigger wires, too. Keep in mind that as built this circuit will not handle 60 A even at lower votage.
Input?
60 volts and output variable
input kitni h ?
Maximum 60v
Can we use this as a solar charger controller
how do i can control current?What should i need to add in the circuit to control current also??
This circuit isn't even a voltage regulator in any normal sense of the term. All it is is a voltage "follower." The output voltage will vary with varying input voltage and with varying load. It is more or less the equivalent of a an adjustable power resistor (rheostat).
Hello👋 if you have 60v output, what was the input current
Bonjour,
Est ce possible de faire tourner un moteur d'aspirateur a 2 vitesses différentes sans potentiomètre.
Precisa de transformador de 60 volt né
Yep, you can use 60v transformer with bridge rectifier and (filtered rectified output dc) will go to this circuit to make voltage variable.
062423/0426h 🇺🇸 Thanks. What was your input voltage and current? What was the Output current depending on load?
Nice mate, Can this circuit handle 120v input?
This igbt can handle upto 600v input but at lower current
Can we use this as a solar charger controller
...habría que adaptar el divisor resistivo a la Vin para obtener Vge adecuada.
...the resistive divider would have to be adapted to the Vin to obtain adequate Vge.
@@frank0-1 thanks
@@MQVlogspk ...este circuito no sirve como controlador de carga solar. Para ese fin te hace falta un MPPT.
@MQVlogspk ...this circuit does not serve as a solar charge controller. For that purpose you need an MPPT.
İnput 48 V 8 A about 380 Watt can i get 12 V 30 A ? Or output current should same with in max current
What is out put current according to variable voltage?
Input voltage?
Input voltage dc 60v and output variable
لماذا تجاهلت قيمة توتر الإدخال؟
In put supply how many
Mạch này nội trở rất lớn
Can you replace this transistor with IRF1404?
ok, so what is the supply voltage? pls
Input voltage 60 volta dc and output variable
May I know the input voltage
...60V
What is the voltage drop when a 30-amp load is put on this circuit ?
30 amp @ 14.8vdc
It drops SMOKE, as he had 60V input, thats going to be ~45v x 30a = 1350watts dissipated.
Si necesita solo 15V no lo debe alimentar con 60V porque la diferencia la tiene que absorber el IBJT que solo soporta 300W a 25°C.
If you only need 15V, you should not power it with 60V because the difference has to be absorbed by the IBJT, which only supports 300W at 25°C.
What is the input voltage? .Is it above 60 volt Dc?
i think it is AC
It is NOT a voltage regulator. Output voltage is roughly proportional to input votage. It should be independant !
Jab supply pe load dalte hai tab supply Kam ho jati hai kyu
Fake circuit
if I want to make a variable voltage 0-300vdc, what component is replaced by value?
The resistors and potentiometer.
It has a video where instead of installing a potentiometer, it is better to install a holl sensor and also reverse for a 72v 80A motor
Good
Thanks for watching
- DC in ? volt
Fet ?
What's the supply voltage
Input 60 volts and output variable
40A ?
DC in ????
Input 60 volts and output variable
Input voltage pl.
Please show the supply input to the circuit. Tq
Input voltage?
Dc 60v & output variable
Input maximum ampr......?🤔
👋👋👋
First Comment
Thanks for watching my friend 🙂
can add ampere limiter?
You can check out voltage with current regulator video on my channel
Of course, if you use a 60 volt output, what's the point of all this fuss? Otherwise why not show it? I need to stop wasting time on these useless sites
Hi bro please show the circuit diagram 🙏🙏🙏🙏
Circuit Diagram download link is in video description
@@CreativeTechos thanks bro
ไม่เห็นบอกอินพุทเลยครับ
Not taking current
Thank.đang cần hạ áp sạc xe đạp điện.
Show
👍
building a model that shows the way of connecting household appliances can you show how to do and please help me i need for school project please please please ✨✨✨🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹🥹
Где показания тока обман?
too many heat, not ok
1 а мах
Dc 220v regulatar banao
60 volt 0.000000000000000000000001 Amper.....
😂😂😂
Why is there a capacitor in the circuit? The circuit works fine without the capacitor!
Show
👍