I’m sorry my friend I had nothing to compare it to as it did not come with one. Definitely 50 to 70grams heavier but the sound and response is mind blowing. She weighed in at 19.8 pounds total. With (2)-4000mAh 2s and (2)-6000mAh 6s lipo’s. The recommended CG is way too nose heavy. If you have a paved and long runway you will need it with the recommended cg. I found the perfect spot at 196mm from leading edge using the jig it came with. Good luck and always have fun my friend.✈️🙏
Hey, great set of videos you have of this bird! I just acquired one myself and have a question or two: 1. It looks like you have maybe just a partial intake duct in this video, not going all the way to the fan as described in the kit. Is that what you ended up with, and if so, has that worked well? 2. What did you end up with as far as the LIPO capacities? I have almost the same setup planned. Almost identical except for a JP fan unit instead of the HSD. Thanks for your response. Newly subscribed!
1st ? I cut the intake tubes just past battery tray and I did not install front nose shroud/plastic piece for air flow. You want good air flow over your batteries and plenty of air for your fan. 2nd ? I am running 12s (2) Admiral pro 6000 6s. I added (2)-2s 4000 G2 batteries for all electronics and perfect CG. The recommended cg is extremely nose heavy. I wanted to make a video on how to set up/modify your jig for the perfect CG. This can save you a ton of flights and time.
Hey man, I’ve had this plane since last year and it’s a blast. To answer your questions I also did an “open-duct” system and cut the intakes short. It seems to enhance the sound but it definitely reduces efficiency. As far as the fan/LiPo’s I went with the JP hobby 12S 120mm and it’s been great. I used 5000’s to start but flight time was limited. I’m currently using 6200’s and plan to bring on some 7200’s next month. Hopefully this helped!
I ordered the ones from Motion RC I’m not sure why it’s $289 as a set so I bought everything separately for $30 cheaper and I still received the hardware. The nose strut on these retracts are way too stiff. I may replace with the one that came with the model
@@comeflywithmercI ask as I am currently building mine, I will use the same EDF as you just wasn’t sure to use Lion batteries or Lipo. Thank you again and wish you all the best for the maiden.
@@JP-ij6gf I’m using lipo but I’m amazed at the flight times this EDF jet guy is getting with the lion’s Samsung.🤔 maybe the future battery for sure. Mark my words.
@@comeflywithmerc Thanks for the information. Just purchased the last one in stock from Turbine RC last night. Got tired waiting for Motion RC to get some in stock.
I used Spektrum 2s receiver lipo batteries. It has receiver output and ic3 connector. I purchased ic3 opposite connector and connected directly to brakes module. The receiver connection to the light module. I used the same gauge wire for the brake module to ic3.
@@comeflywithmerc I am in the final stages of building mine and want to minimise the amount of batteries on the aircraft which is why I asked. Need to reduce the 2S batteries from 4 down to 2. Once again, thank you very much.
We love it serg. Super cool. You are one in a million. Wish we could be there when you fly this Saturday.
Thank you my brother! You were there for the unboxing and God willing all goes as planned 🙏.We will post full uncut video.
Just bought one today from Motion RC. You did a beautiful job!
You made the best decision.💪👊
Dang this thing looks so good!! 🙌🏼
Thank you my RC brother! Can’t wait to fly her.
WoW! So amazing unc your the best
👆🥰💪👊✈️🤪
very nice build. what is the weight difference in the thrust tube compared to mylar?
I’m sorry my friend I had nothing to compare it to as it did not come with one. Definitely 50 to 70grams heavier but the sound and response is mind blowing. She weighed in at 19.8 pounds total. With (2)-4000mAh 2s and (2)-6000mAh 6s lipo’s. The recommended CG is way too nose heavy. If you have a paved and long runway you will need it with the recommended cg. I found the perfect spot at 196mm from leading edge using the jig it came with. Good luck and always have fun my friend.✈️🙏
How are the KingMax mini servo CLS2875H your using on the jet? Looking to use the same servos. Thanks Charles
I love these servos. I highly recommend. Running them at 8.4v.
Thanks@@comeflywithmerc
How do you keep the covering from bubbling up in the sun?
Low temp heat gun from hobby lobby
What servos did you use on the wings and tail. The recomended bundle pack Motion shows are WAY to big.
KingMax mini servo CLS2875H on all control surfaces.
I did have to file about 1/16” to make them fit
Hey, great set of videos you have of this bird! I just acquired one myself and have a question or two: 1. It looks like you have maybe just a partial intake duct in this video, not going all the way to the fan as described in the kit. Is that what you ended up with, and if so, has that worked well? 2. What did you end up with as far as the LIPO capacities? I have almost the same setup planned. Almost identical except for a JP fan unit instead of the HSD. Thanks for your response. Newly subscribed!
1st ? I cut the intake tubes just past battery tray and I did not install front nose shroud/plastic piece for air flow. You want good air flow over your batteries and plenty of air for your fan. 2nd ? I am running 12s (2) Admiral pro 6000 6s. I added (2)-2s 4000 G2 batteries for all electronics and perfect CG. The recommended cg is extremely nose heavy. I wanted to make a video on how to set up/modify your jig for the perfect CG. This can save you a ton of flights and time.
Hey man, I’ve had this plane since last year and it’s a blast. To answer your questions I also did an “open-duct” system and cut the intakes short. It seems to enhance the sound but it definitely reduces efficiency. As far as the fan/LiPo’s I went with the JP hobby 12S 120mm and it’s been great. I used 5000’s to start but flight time was limited. I’m currently using 6200’s and plan to bring on some 7200’s next month. Hopefully this helped!
Hey, bro... information please! I purchased the same light kit as you, did you connect it directly to one of the spektrum receiver channels?
Awesome job, looking good, what retracts are you using my friend?
I ordered the ones from Motion RC I’m not sure why it’s $289 as a set so I bought everything separately for $30 cheaper and I still received the hardware. The nose strut on these retracts are way too stiff. I may replace with the one that came with the model
@@comeflywithmerc thank you very much for your response, most appreciated. Using 12S do you have any idea what your flight time will be?
@@JP-ij6gf I’m hoping 4-5 min with good throttle management 3-4 heavy on the throttle. Maiden set for 3 1/2 minutes
@@comeflywithmercI ask as I am currently building mine, I will use the same EDF as you just wasn’t sure to use Lion batteries or Lipo. Thank you again and wish you all the best for the maiden.
@@JP-ij6gf I’m using lipo but I’m amazed at the flight times this EDF jet guy is getting with the lion’s Samsung.🤔 maybe the future battery for sure. Mark my words.
What lighting system did you use?
RC Plane Lights RC Plane LED Light,Simulated 14 LED Flashing Light Lamp System, for RC Aircraft Plane Glider,RC Flashing Light RC Part rc Plane Lights a.co/d/8ArYxdv
Did this come with LEDs for the wings, or did you have to cut them out.
No, I bought a light kit and drilled them out! I ran three separate wires for different functions
@@comeflywithmerc Thanks for the information. Just purchased the last one in stock from Turbine RC last night. Got tired waiting for Motion RC to get some in stock.
@@TeslaModificationInstaller you’re going to love it! My favorite in my hangar! She is a pretty big bird!!!💪👊
@@comeflywithmerc Mind telling me what servos you are using?
@@TeslaModificationInstaller (7)- king max mini servo CLS2875H and (1)- tower pro mG92b
Hey buddy, how do you connect brakes and lights to one lipo?
I used Spektrum 2s receiver lipo batteries. It has receiver output and ic3 connector. I purchased ic3 opposite connector and connected directly to brakes module. The receiver connection to the light module. I used the same gauge wire for the brake module to ic3.
@@comeflywithmerc very helpful, thank you very much, wish more people were as helpful as you are.
@@comeflywithmerc I am in the final stages of building mine and want to minimise the amount of batteries on the aircraft which is why I asked. Need to reduce the 2S batteries from 4 down to 2. Once again, thank you very much.