ACCORD F22 PART 6 CYLINDER HEAD INSTALL | 2.2L 2.3L | Prelude Odyssey | Blown Head Gasket | Fel-Pro

Installing head and head gasket on a Honda 2.2L 2.3L F22 F23 engine, Accord Prelude Odyssey. Fel-Pro head gasket is used as well as the intake manifold. Not really hard to do just time consuming. Covers Honda Accord Odyssey Prelude from 1994 1995 1996 1997 1998 1999 2000 2001 2002.
LINKS TO HEAD GASKET AND INTAKE AS WELL AS TOOLS AND OTHER STUFF
Honda Accord Odyssey Prelide 2.2L F22 Head Gasket: amzn.to/3FAjULn
Intake Manifold Gasket: amzn.to/3M5UWpN
BEST Dielectric Paste: amzn.to/3KJL053
BEST KIMO 3/8ths Electric Ratchet: amzn.to/3o51OK0
BEST RTV IN THE WORLD (FIPG): amzn.to/3s09hLB
BEST Anti-Seize for Spark Plugs: amzn.to/3KNE9Y9
BEST Mechanic Work gloves: amzn.to/3KTBBYv
BEST Zero Offset Wrenches Metric: amzn.to/3KTAIzs
BEST Metric Wrench SET: amzn.to/3u2NHIZ
BEST Underhood Work Light: amzn.to/3u4EOOW
BEST Headlight Restoration Polish: amzn.to/35w94YY
BEST Synthetic Motor Oil: amzn.to/3u3uM0E
BEST Headlamp Work Light: amzn.to/32ISTqe
BEST Grease for Wheel Bearings: amzn.to/3rQ1ik8
BEST ½inch Electric Impact: amzn.to/3IMa89c
3M Dielectric Paste: amzn.to/3KJL053
LINKS TO PREVIOUS VIDEOS
VIDEO 1: • ACCORD F22 Camshaft Sn...
VIDEO 2: • ACCORD F22 Camshaft & ...
VIDEO 3: • ACCORD F22 PART 3 | AB...
VIDEO 4: • ACCORD F22 PART 4 CYLI...
VIDEO 5: • ACCORD F22 PART 5 | MA...
More About BundysGarage:
goo.gl/qv3Wzc
Questions, Comments, Concerns:
[e-mail]
Twitter:
/ bundysgarage
@bundysgarage
On The Web:
www.bundysgarag...
Music by Randall Kent: As seen on NCIS
• Randall Kent - Going H...
All Rights Reserved 2022
© Copyright 2022
Bundys Garage
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: [e-mail]
DISCLAIMER - DISCLAIMER - DISCLAIMER
Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.

[@mckoylach1622]

Great step by step procedures, thanks

[@pirihern9329]

Just viewed part 5. Completed timing belt replacement with all related yesterday. Noticed oil / coolant leak at oil cooler lines

[@pirihern9329]

Also replaced cam and crank seals plus keeper on balancer shaft seal.currently driving my 2006 Subaru sti

[@crystrezerex2life]

I curious to know which way all these gasket go when installing,...which sides are up....none of the felpro gaskets I have are marked.

[@watuzi]

What was the 1/2 breaker bar connected to? Was it to hold the pulley in place while you loosen the crank pulley? I know you did this setup before. Thank God I never have to do this shit. Too scary for my taste, brother. Maybe you can do a mid-2000 GM timing chain next time. Thanks 🙏

[@bundysgarage]

It was lodged up against the upper control arm

[@Dillon1791]

Did you check to see if the the rest of the cam seized in the old head?

[@randycantor5210]

Mm😅🎉😮😂

[@hadiitiniguez2393]

Can you fix my car? Thank for the information