Nespresso VertutoPlus leaking, full disassembly and cleaning.
HTML-код
- Опубликовано: 11 окт 2024
- In this video you'll see the process of disassembling of VertutoPlus to identify leaking problem. also a way how you can access bearing for noise problem and how you can clean internal tubes or compartment from the coffee.
Tools:
T10 screwdriver (with hole in the middle )
Philips screwdriver.
Spatula tool.
Don't forget to like and subscribe.
Thank you for this video. Showing the dismantling to my wife opened her eyes to how many parts I will break when I will do this by myself. So she finally released the budget for a new machine 😎
If you'll need something else disassembled let me know ;-)
Best comment on RUclips I’ve seen so far
😂😂😂😂😂😂😂
LOL this is exactly what I'm about to use this video for
You're a hero! A simple top clean and my machine went from deafening to silent!
Thank you for this comment, while my bearing should be replaced...... juat cleaning made my machine silent again! I wasn't going to tear it apart without the bearing until i saw your post!
Thank you for this! I had coffee building up around the edge where the Pods are inserted. I followed your dismantling of the VertuoPlus and found the spring arms were connected to one arm and not separately. The pressure wasnt there clamping down on the pod and it was a successful fix. One thing to note- you will also need a T9 screw as well as the T10 which you note in the description.
Hey man, big thanks from Belgium! My machine occasionally leaked water and the coffee was very watery. With help of your video is disassembled and cleaned it. I still have to test it a few more times but so far the first cups were a success! 🙏🏻🙌🏻
Nope, scratch that. Back to watery coffee. Oh well, at least i had fun with disassembling and puzzling it back together! 😅
На видео все гораздо легче выглядит 😂… все удачно, пошагово разобрал, почистил и собрал обратно. После сборки утечки не обнаружил. Спасибо за видео
Excellent video! Thank you so much! It will be nice to see one fixing the 2 mm up and down move.
I wanted to reactivate my Vertuo and so I bought some pods. Then I wanted to rinse the machine and it was clogged. Thank's to your video I could fix it. Very nice walk through and explanations. If it is possible to fix then you should try to fix it. Better for the World, better for your wallet. And now that it is fixed, I can spend all the saved money on coffee😅
Thanks for this video, cleaning the top portion of thr coffeemaker stopped it from leaking coffee from underneath..you saved me 200 bux!!
Very through - thank you. I was hoping to see where the laser reads the cartridge, but after disassembling much of this machine, and still not getting to the sensors, I will give it back to my daughter. This seems to be an extraordinary effort - three motors, heaters, electronics, seals, springs, etc,, just to cook some coffee. I'm not sure the coffee it makes tastes any better than using a good, freshly roasted coffee, ground right, and brewed at 194 degrees - far cheaper, and ultra reliable.
Thanks for your video. I had to replace the bearing in my machine and if it wasn't for your video l would of ended up breaking it taking it apart. Thanks again.
Excellent video, thanks for taking the time to do this.
My 5 year old machine had been getting quite noisy, sometimes a standard cleaning cycle would help a bit.
However, the other day the machine finally refused to go on! Each time you pressed the button to make the coffee the button went red,
the cleaning cycle did nothing.
I followed your instructions and fully dimantled the top end. The inside of the spiked coffee head thing was very gunked up, it was slightly different to the one you show, it had two metal disks (correction - you do show two disks/gaskets in the video but they appear as one, almost stuck together) I thoroughly cleaned everything I could get to, the machine is now quieter than I can ever remember it! Works perfectly and the coffee tastes great.
This job is not for the faint hearted but your video shows everything you need to see, it's great that you can clearly see how tricky some bits are, and you can get a good idea of how much force you may need to use at times.
Thanks again, you definitley saved me from having to buy a new machine!
extremally useful, but why this stupid music in the background ?😂
My machine just started leaking coffee out the back waterfall, great video, wish me luck 😅
Oh gosh. I’m huge on DIY but this is out of my realm. Thank you for this video tho!!
Thank you. Fully disassemble left for a month and was still able to follow and reassemble
Great job!
Thank you so much for this video. You are correct in that I think it is the only video that shows you a tear down of this machine on the internet. Unfortunately, so far, I have taken mine apart but can’t identify the leak as it is not yet leaking whilst the plastic outer parts have been removed.😂. I will continue to use/test it before putting it all back together, in the hope that it will leak like it did before I took it apart, so that I can identify the problem🎉
Bardzo Ci dziękuję za szczegółową instrukcję!! Gdyby nie Twój film nigdy bym nie rozegrał tej maszyny do kawy. U mnie kawa wyciekała pod gumową uszczelką dociskającą kapsułkę. Mam 2 takie maszyny do kawy. W jednej była popsuta elektronika a w drugiej właśnie wyciekała kawa. Dzięki Tobie wymieniłem całą głowicę w której jest gumowa uszczelka. Bardzo Ci dziękuję za pomoc :) Pozdrowienia z Polski:) Tomek, wojak33
Thank you very much for the detailed instruction !! If it weren't for your movie, I would never have played this coffee machine. In my case, coffee was leaking under the rubber seal pressing the capsule. I have 2 such coffee machines. One had broken electronics and the other was just leaking coffee. Thanks to you, I replaced the entire head with a rubber gasket. Thank you for your help :) Greetings from Poland :) Tomek, wojak33
Thanks.
Thank you for the tutorial on how to dismantle this machine. Mine was not pouring water.
Wile removing the top mechanism, I noticed that it was not rotating. The ball bearing was dry and seized. I just open it, force some grease into it and make sure it was moving free.
I cleaned all the components. Reassemble it and voilà!
Back on the road!
Good that it helped , don't forget to subscribe.
This is our second K-Classic. We had our first one for many years, so when we had to replace it, we wanted nothing else but this exact ruclips.net/user/postUgkxBrV-RbF5Nk0Rlt9i15aao-YMzqzTG8Vf model. We use it for about three people everyday in the morning. The taste and quick brew is one of the reasons we like it so much. There are so many choices of brands of coffee that we would grab what was on sale and test the different brands from there. I would definitely recommend trying different brands of coffee to find the ones you like the most because there are brands that quite frankly taste horrible.
excellent video, very interesting, understandable and clear, I'm a new subscriber! I love fixing things and figured my noisy machine needs a new bearing - but I see this is just a bit too hard for me. I enjoyed watching you disassemble it. Thanks for supporting the brave folks in Ukraine.
Thanks
Thank you for the video, it was of great help. For further dismantling a T15 screwdriver is needed.
BTW if anyone knows how to use the water pump (ulka HF) alone. It's for repurposing project 😅
Well done! This is like the how is made channel. Thank you
Great video, easy to follow! I wanted to replace the bearing and couldn’t free it from the other piece. Any ideas? Thanks!
Thanks for your video I dissadembly mine and now i fixe it for good
Thanks. This is helpful. I’ve just decided it’s better to get a new machine.
Nespresso must made this machine like this intended to breakdown around 2yr of usage to make customer upgrade to newer machine. I’m a tech and a mechanic and can see they made overly complicated to dissemble to replace a part that could easily worn out within a year of usage.
This video much better angles than vertuo silver head . I still do not know how the springs and things near front of head are taken off and replaced. I rwqlise it's very hard to make videos , camera angles , steady , not blocking with your own arms and hands etc in video . Good job I only wish in that video front was more visible . This video perfect job thank you so much 🙏 ❤
Thanks
I have no play in gray plastic pod holder that spins and there is leaking with the extra aluminum pod skins I fitted. I will take apart the top as in your excellent video and diagnose problem and consider Wojak’s gasket repair!! TY I subscribed!
Just what I needed! Thank you!
Hi there I’ve just gone through the amazing video. However I have a slightly different problem - looks like the motor is stuck with no power. I’ve disassembled my machine and completed the first half to remove the top. Just about managed to complete that with “lid” opening about 8-10cm. Put it all back together and started on the bottom but the sleeve won’t go high enough to remove. Any tips??
Thank you. Enjoyed step by step for the Nesspresso vertuo round top. There was lots of coffee ground accumulation behind the disk behind the bearing. After cleaning noise went away. Wanted to changed the bearing while at it and 6901 bearing ordered on Amazon wasn't a match it was a smaller. What is correct bearing part number.
My machine was doing the red ring of death but it sounded like it wasn't spinning. So I opened it up greased the ballpoint and cleaned it up and now it's working 🤘🤘
Cool
Thank you for the precious information, I'm trying to understand why my machine no longer accepts refillable capsules and the red light comes on, could you help me understand?
Thanks for this video! how do you remove the bearing from the plastic piece? Im having a hard time removing the bearing from the black plastic which it is attached to. im trying to clean the bearing as its very noisy. Thank you
thanks for the video is great! I just start disassembly the machine. Do you have any suggestion on what issue I can have? the led is red. it start making coffe but after 2 sec after pressing start Botton it stops. I've done the reset and all the procedure but still doesn't work..
Thanks for the amazing video. By following it, I removed the top lid and clean up some water leak and it worked. However, my VertuPlus got flashing red three time a second now and the top lid doesn't open when I push the bar. I can't remove the pod. Is there a way to get the top lid open?
The bearing is the biggest problem I have experienced with this model as the noise it made was unbearable and likely not good for the machine. The bearing is a series 6001, which is 12x28x8mm in size. I scoured the Internet for the size/type of bearing, but found no mention of it anywhere for this Nespresso model. The bearing I took out was 6001-2RS (rubber sealed). I replaced it with a 6001-ZZ (metal sealed) Timken bearing purchased from Amazon (2 bearing package for $16). There is significant force required to remove the rotating section from the machine as well as the bearing from the rotating section. I used a 0.75” wide plastic pry bar and worked the bearing off going around the circumference.
I don’t recommend taking the rotating section apart (4 screws) as it is a bear to put back together. I did and found some small bits of coffee, but nothing serious. If you must take it apart, before you do anything, mark where the 2 plastic parts align (tape). When apart, mark where the metal rings align (felt marker). When you put these 2 plastic parts back together, I placed the bottom (sharp) piece on a 1/4” measure cup to provide support, while allowing the center shaft to go inside the cup as the spring is compressed with the top piece.
Great video, which I paused and rewound as I went along. There is no way I could have done this bearing replacement without this video.
Thanks.
Can you describe how you pried the bearing off? It doesn’t seem to move at all
@@danhaar4112 I used a 0.75” wide plastic pry bar and worked the bearing off going around the circumference. The ~8" long pry bar was from a collection I had to work on the interior/dashboard of a car. Anything thin & narrow & strong enough to put some upward force that fits under the bearing in the space allowed will work. Be patient and slowly work it off by going around the entire circumference of the bearing - may need to go around the bearing circumference more than once if it is jammed on there.
Excellent take apart. Too bad the bottom wasn’t taken apart. I used one bottom pod skins to build up the coffee filled pod, it still leaked. Now will try two skins over the bottom of a coffee pod.
Has anyone tried a 2mm silicone gasket on the brewing head??
Great video; I also like that you support Ukraine! This type of construction is very similar to the Keureg machines-lots of hard to release clips of plastic.
Hi. This is one of the most informative Nespresso demo available. Thank You for sharing. Don’t mind the background music. One question if I may, the dismantling is great, do you have a breakdown of what elements of the device cause what faults? The constant RED light is an issue and would appreciate some guidance if known. I have a Nespresso that is RED light on and when the device is about to draw water from the reservoir, it errors. I can hear the motor start but, it is almost like, there’s a blockage. You input will be much appreciated.
I never had this error but maybe it can signee that pump is blocked or not working. or sometime the electronics can get wet.
Were you able to solve the problem? I also have a constant red light.
My machine had a red light error. We took it apart and saw that the coffee/water had dripped on the centrifuge motor, rusting it and keeping it from turning the centrifuge
Hi folks.
Not managed to repair yet but I noticed there are several service parts available in the UK such as pumps and maybe, someone can identify the most likely part required for this issue.
HTTPS://www.espares.co.uk
Too be honest, not knowing what the cause could be, I can’t justify spending money on several parts.
There is definitely something not drawing the water through so I do think it is a ‘flow’ problem!
I would imagine it is a common problem though, no one I can see, has managed to post a result.
Mine is in a box in pieces and unless, fixed, will just be discarded. Shame really but I am an advocate for repairing and recycling wherever possible.
@@hannahguichet9537 Hi Hannah.
Thanks for posting and really interesting find.
From the link I posted for
Http://www.espares.co.uk
Are you able to identify the part required or have a picture of your find?
Best regards.
Dave.
Thank you! This was so helpful!
Glad it was helpful!
Hi. This is the only video I've found thats useful when trying to fix one of these babies! I have a white vertuo machine that is refusing to close.... also the little front cover that is just under the tap button is hanging down exposing the elements between cover and buttons. Do you by any chance have a video /advice on fixing a machine that won't close? Thanks
The mechanisms are not so difficult to understand see what's blocking it.
How many years was this working prior to disassembly
Very informative. Thank you. I accidentally closed the machine while assembling and now it turned red and won’t open. Is there any ways to unlock it manually?
Need replace the bearing but cant remove it from the shaft that holds it. Can you help me how to do it?
Did you know how to remove the middle part where the capsule sits and reassemble it back?
What is the name of the gray part where the capsule is placed inside the coffee maker?
where can I buy it?
How do you remove the bearing from this specific machine? Need to replace because of the loud squeaking noise? I tried prying from underside of bearing but it’s not budging at all. Any help would be appreciated!
My coffee machine stopped working. I had to replace the triac. But after assembly and switching on there is no reaction. How can I check if there is a problem with the pump or something else?
Hi Roma Fix!
I am wondering if the parts of the machine that come in contact with the hot water are made of plastic?
I am looking to buy this machine, but I do not want to if the parts of the machine that transfer hot water are plastic.
Thanks!
Hi! Thanks for the help.
My machine is extremely loud, my guess is that it's the bearing, any idea how to get the bearing off this exact model you took apart here? It feels like it's cemented.
it should go out.
My coffee maker leeks from the hose underneath of it. How do I fix that?
Very informative, but my machine will not lift and eject the capsule, any ideas please.
Рома, дякую! Була інша проблема з цією машиною. Завдяки Вашому відео зміг відкрити верх 😀
Без проблем )
my vertuolineplus also leaks coffee on countertop. @28:00 you explain leaking but what is the repair solution then ?
there can be multiple problems.
Thank you for video.. I would like to know what us the piece of music playing in the background?
Erasing Egos. Paul Revere Intro.
Спасибо Роман
Мужик, очень помогло. Спасибо
No problem.
Thanks for the video,❤❤❤
Bonjour, la même en français s'il vous plaît. Qu'utilisez-vous pour enlever cette vis?
Merci
Thanks but let me know how to open lid without electricity or mechanically open it
Thank you so so so much ❤
Hi i have this model machine. Mine getting loud. Is the bearing the same as the other nespresso machine that you disassemled?
As I remember it was similar. I would recommend to disassemble grease it and in same time check the size it will work for next ~6month good in same time new bearing will arrive.
Very useful. What size is the bearing? Are there any other causes of excessive noise?
Most of the noise is created by bearing. I don't know exactly the size but you can check in my other video: ruclips.net/video/vT-6lHBTfgI/видео.html
How do you advise to fix the play in the shaft, im willing to pull it apart as it was given to me and I would like to use it
You need so see what part has a lift and replace it.
Hey there, is there anyway of adjusting the temp of the water/coffee on these if you have it apart?
Don't think so.
The bearing for this machine is different from the other video. Where can I get a replacement bearing?
The bearing is a series 6001, which is 12x28x8mm in size. I scoured the Internet for the size/type of bearing, but found no mention of it anywhere for this Nespresso model. The bearing I took out was 6001-2RS (rubber sealed). I replaced it with a 6001-ZZ (metal sealed) Timken bearing purchased from Amazon (2 bearing package for $16).
The motor that spins the capsule is corroded and seized up, but I don't know how to remove it!
I've worked with intricate gearboxes. This is worse. Very anticonsumer design down to the non-phillps screws. They really expect you to just buy a new machine.
Bonsoir , le joint a 17.50mn le mien est mort, savez vous ou le trouver? je ne trouve pas...
Good evening, the seal is 17.50 minutes away, mine is dead, do you know where to find it? I do not find...
Check on amazon or aliexpress.
i have this machine it's making a loud noise when brewing. does the bearing need to be changed ?
usually yes.
O can give instructtions to fix IT for good you require some shimms washer i use a ring for a Keychain about the size of the ballbearring and IT work just fine i have the last Assembly picture Edith the shimm but I dont know how upload it
If the top is dirty can this cause the machine to be extra loud whilst brewing?
it the dirt is inside the bearing then yes.
Thanks a lot!
Can it fix red ring of death?
Need help! Can’t get the sides off. Not sure what you’re pressing in order to get top to move up.
I had the same problem. What work for me finally was to insert a thin pry tool on the bottom front curve part where the 2 side meet and pry upwards to first release it from a clip there. Then I used a small plastic mallet and gently tap the bottom of the side to release the side from the rest of the internal clips.
My machine is definitely showing the freeplay up and down. I ran it with cup catcher off to confirm that it is leaking from the cup area. Your video ends with not showing how to fix that, and you don't know what is actually causing it. So I spent 35 minutes watching to find out that I need to replace the unit.
Very helpful thank you
You're welcome!
hi very impressive video cab you consult regarding an electronic problem? tnx
usually electric problem is caused by the water check for corosion
@@RomaFixcom hi tnx a lot that machine is a brand new was bought in the USA and was plugged at 220vac instead of 110vac...so i fixed the damages and power supply of 15vdc works but no 5volts since enable command is missing and since no schematics i cant find who is responsible for the enable interlock to work....
شكرا
잘봤어요
I have lately problem this machine last 4 pods, excessive vibration. Coffee grind on top lid of pods, not past lip , between center hole and inside rim diameter holes, I carefully remove hot pod from machine not letting it tilt eject , My machine is from 2019 or 2020 silver round head vertuo same one you show bearing replacement . Is this a problem anyone else has ?
I had similar was problem in metal rods that keep the capsule but yours maybe different.
Red Light and NO PUMP running. Need to see the best way to remove the pump and test.
How do you remove the bearing on this machine to replace it
you need to twist gimpy part with hands and after remove the bearing.
useful info , but why there is that annoying music in the background, regular Torx T10 without temper resistant hole worx OK 😂😂
It’s help me understand the dismantling but last minute I felt like abandoned.the main problem is still there….
it mostly for cleaning and disassembly.
La mienne est bloqué veut pas ce fermé svp une vidéo pour régler ce problème.merci
No sorry.
Does you fix the leak finally?
this was warranty machine and to fix it I needed to disassemble bottom part to see why it shifting, 80% of people wouldn't do it.
Романе, як можна зв^язатися з Вами ?
I can’t get the top part off to save my life I can not figure it out
Thankyou for your video. Some of these fail because the tiny yellow (teflon?) lip seal under the pressurised pod chamber has a very limited lifespan. When it starts weeping, liquid is allowed onto the lower 24 volt DC motor, which severely limits it's life..... Hopeless design. See my video at ruclips.net/video/cCdbVMdCzR0/видео.html
Im curious, who has the time to go through all of this to replace a part and put it all back together, to find out it may not fix the problem and you have to take it apart again and change another part???? All for a $100 coffee maker from china? Seriously
Funny enough, the one I bought 4 years ago, was made in the Ukraine, seriously. Sure letting repair it will cost you the price of a new one, but if you're in DIY then why not give it try and help save some Ressourcen.
Stop with music. distracting and interferes with audio
You can always mute it )