Hi Mark, I am big fan of your channel and learned a ton of knowledge and I can’t stop thanking you. I would like to make one suggestion. If you have a doubt on the filter isn’t that you can do a continuity test from the LCD pin to filter if the ZXW doesn’t give the detail wen you click on the component???
Hi, Congratulations on sharing with us and with so much clairvoyance, I have a question, I do not have this component available at the moment, but can I substitute for one of another iPhone besides the 8?
Hi, hope someone can help me. I have an iPhone 8 with backlight issue and a donor iPhone 8 board (intel). 35, 37 and 39 are normal value on J5700. R5733, R5734 and R5735 are good. D5661 and D5660 are ok. All backlight capacitors are normal. Just in case I have swapped R5733, R5734, R5735, D5661, D5660 and U5660. The donor working fine with those parts that I have taken out from the other one but the phone still has backlight issue with the donor's parts. Any idea, please?
Hi, J5700: All pins value are good U5660: All pads value are good U5660: changed D5661: Changed D5660: Changed R5735: OK R5733: OK R5734: OK All capacitors are OK Do you have any idea what can be wrong?
Hello friend thanks for all your sharing . I have same issue no bkl after waterdamage I get DWI_PMGR_TO_BACKLIGHT_CLK too low in diode mode about 0.100 Any idea ??
Hi Mark, I am big fan of your channel and learned a ton of knowledge and I can’t stop thanking you. I would like to make one suggestion. If you have a doubt on the filter isn’t that you can do a continuity test from the LCD pin to filter if the ZXW doesn’t give the detail wen you click on the component???
Pls Sir can I jump wire instead of changing the ic
Hi, Congratulations on sharing with us and with so much clairvoyance, I have a question, I do not have this component available at the moment, but can I substitute for one of another iPhone besides the 8?
Please post your question here and I will answer it: www.microsoldering.com/community/
My backlight works and lights up the screen but the screen itself is blank only lighting up not showing anything on the interface.
yes
I have a backlight problem on my 8 Plus. I have a dark shadow in the bottom right of the screen should I follow your way of doing it?
Please post your question here and I will answer it: www.microsoldering.com/community/
Hi, hope someone can help me. I have an iPhone 8 with backlight issue and a donor iPhone 8 board (intel). 35, 37 and 39 are normal value on J5700. R5733, R5734 and R5735 are good. D5661 and D5660 are ok. All backlight capacitors are normal.
Just in case I have swapped R5733, R5734, R5735, D5661, D5660 and U5660. The donor working fine with those parts that I have taken out from the other one but the phone still has backlight issue with the donor's parts.
Any idea, please?
Hi, J5700: All pins value are good
U5660: All pads value are good
U5660: changed
D5661: Changed
D5660: Changed
R5735: OK
R5733: OK
R5734: OK
All capacitors are OK
Do you have any idea what can be wrong?
Sir i have same problem in my phone and i have successfully repair it with the help of your vdo
I DID THE SAME THING BACKLIGHT WORKED BUT NO TOUCH SCREEN, ANY FOLLOW UP?
Check your touch pins with PS
Hello. It worked well replacing with a filter. But the original component actually is a 0ohm resistor!
Okay that makes total sense! Duh!
Even so, its Best to put a filter as a Protection for the rest of the line.so if it happens again,the filter is there.
Is it possible then to use a simple solder bridge instead? For example, just add short the 2 contacts with some tin?
@@declanross4484 Yes, 0 ohm offers no resistance at all
Hello friend thanks for all your sharing . I have same issue no bkl after waterdamage
I get DWI_PMGR_TO_BACKLIGHT_CLK too low in diode mode about 0.100
Any idea ??
Iphone 8 screens will have metal tabs at the top whereas the 7 has plastic hinges