Side gapping is used in Racing . High Fuel Ratios and High temperatures . Side gap plugs dissipate heat from themselves quicker to avoid overheating and Melting the Electrodes . The Plugs do NOT make more Power . Even a High-end MSD ignition doesn't . What happens is MISFIRES are eliminated .
many years ago I had a single cylinder 185 suzuki 2 stroke that had 2 spark plugs in the head so if one fouled you could swap the lead to the other one for a fresh plug. But what I did was add another coil & lead to the second plug so both were firing & it made a huge difference way more low down power & always started so easy.
Not sure if you know this but the second sparkplug hole was originally for a decompression for easier start then it was found they didn't really need it so it was used as a spare plug,interesting how you hooked both up though that's pretty cool.
the steady spark is because it connects the closest points. with the original the surfaces are parallel and spark can form anywhere between the parallel surfaces but will have the same power every time. With the side gap the location of the spark is constant and will wear the side of the electrode then the gap will increase. It is possible the flame will travel slightly better because it can spread in all directions initially but hard to tell if it helps without clear tests
Idk why people write so much hate to you. I have a 50cc and I am just like you, I like trying homemade things to make my moped better. I love your videos!
For all the comments putting down his testing. This is simply some of the ways you get in the fast lane. Test and trail. If you don't like it just stay over there in the slow lane👍
I've been grinding my spark plugs since the 1960s, except the Iridium plugs. [Dodge D-50 2.6 5 spd.] I VASCAR tested 1/8 mile of 3 runs (averaged) & went from 14.25 to 13.75 seconds. My mpg's also went up. __ CHEERS 😉
I side gap my 2 stroke lawnmower spark plug, it stops fouling. My nieces husband came for a visit, his car wouldn't start so I removed the plugs, the outer electrode was almost completely burnt off so I gapped what was left re fitted them and it ran.
Side spark in racing has nothing to do with the ground terminal blocking the combustion. When the spark "dances" it changes length and there fore temp. Racing calls for consistency of high performance precision at the cost of longevity. You electrode and ground post are going to concentrate all of the wear in one "laser" spot increasing gap wear quickly out of optimal range. Not an issue if you change them after every race.
The ignition has to be able to create the spark longer too. I used side gapped plugs in 2 stroke engines turning 20,000 rpm. But the pumper carbs had externally adjustable low and high speed jets .The plugs were alot foul resistant in 2 strokes for sure
For you to get anything from the plug if you got more consistent spark you would need to alter the gas and air mix because it most probably running lean and the plug is burning it up quickly and if that helps but doesn't solve problem change jets size for more fuel
Good info dude! Now do research on indexing spark plugs. If you index them, you'll get the electrode facing directly at the fuel air mix when it enters the engine making even more power
You can try to advance the cam by 1 tooth or 10 degrees. The stator coil pickup might be able to be modified so you can advance the timing a few degrees
Good answer it's unbelievable just how many people that will talk like they know everything but don't know anything. Reading your comment let me know that they're still ppl who have done it and know what to do.
If I had that xr100 and was desperate for more power I'd sell it and get the 400 as a step up or the 650r which is in my opinion the best enduro I've ever owned wish Honda would make them again
looking at your spark plug its fooled you need to adjust your mixture also keep the plug standard with the correct gap and also your carb is junk because the carb has the choke butterfly in the way at the rear that stops power chuck in bin by a cheap molkt brill carb that will fit and finaly change your sprocket up a tooth for higher top end 1 tooth less for more acceleration but less top end , you got to get the combos right .
Find your high speed best mixture by getting some jets that are a little bigger and a little smaller than what you have stock. With no other mods on the bike tuning the carb will be best bet. Do the high speed tuning to determine jet size at full rpm. I will assume you need a smaller jet than what you currently have. Then set that needle up a position at a time until your revving from idle on up is the quickest it can be, ie, no bog. Do this and you will be surprised I think. Maybe after getting good air fuel ratios you can play with modded plugs. Good luck!
The only way more spark will give you more power is if you’re dumping more fuel than can burn with original spark. But more fuel can’t burn without more air. The key to horsepower is air. That’s the first thing you need to gain power. Once you get more air in it you can add fuel. And unless you’re dumping a lot more fuel in it I’m sure your original spark can handle it. It is fun to try though lol. Keep at it young man.
I did this with a half clapped out plug on my Stihl backpack blower the other day and no shit..... Starts quicker every damn time now. One pull, always.
Guys don’t do dumb shit with your spark plug, you only have 1 of 2 things, normal combustion and abnormal combustion If you have a problem then modifying a spark plug will not solve the problem An electrical engineer figured this out and RUclips can’t make it better, if this mattered NGK would just make this plug and sell it to you BTW did you notice the spark jumping to ground without crossing the gap first, this plug has a carbon track on the porcelain which is likely the problem
On a small bike engine with,let’s be fair, a small horsepower figure, there’s never going to be an magical and noticeable gain from a spark plug. It’s either going to work or not. What you’d be better doing is playing around with the timing of the spark and seeing what you lose or gain across your power curve. But if you love that bike and enjoy tinkering, drop in a larger lump. 👍
Keep on trying. Don't stop your curiosity. That's how we keep inventing ,thinking outside the box imagine if we stop after the cave man finished with the stone wheel.😅😅😅 thanks for your time to show the difference it makes just by simply cutting the gap a little at a time .
how about... stronger fuel pump, better and more powerfull injectors (better spray), better RAM intake AND better electricity? A better ( bigger ) spark will help igniting cleaner i guess. so maybe.. instead of cutting the spark plug, he could bend the sparkplug so the metal part stands up more. So the spark needs to travel further and deeper into the engine.
@@Satori-Automotivetheres no fuel pump or injectors or short ram (seems like you are talking about cars) however he could get a bell intake or velocity stack for the carb. He could get a racing version of his ignition coil, maybe racing CDI, spitfire cable and one of those iridium spark plugs which give a "laser beam" spark. More air and fuel will give more power so a cleaner flowing exhaust and exhaust tube with the power bomb thing would be nice. As well as bigger valves and head porting. He could also raise the compression ratio. Edit: custom camshaft with more opening and overlap would yield results and he could also mess with spark timing and carb tuning
It can make more power, if it burns more of the air/fuel.. no engine burns 100% but the closer you get the better. More burned fuel = more power. But most likely not enough to worry about.
I'm no expert but in order to gain power from firing you would have to change your stater and CDI and higher voltage coil. You can buy high performance cdi boxes and they will boost engine performance. I put a high performance cdi on my son's pit bike and it made a world of difference in the throttle response and cruising. It was so much smoother than the factory when I first started it I had to adjust the idle down cause it was idling 6 to 800 rpm more with no fuel change and when you held it at a constant rpm speed it so smooth. Also you can buy offset keyways to advance your timing. Just wanted to share for all the keyboard warriors saying that spark won't help performance clearly never set the timing on a small block or anything for that matter. Timing and spark are very important you could have the biggest baddest built engine in the world with the biggest fuel system but without proper timing and spark you have the worst performing engine. Also if you want better spark don't cut your plugs just go to the Auto parts store and get the hottest spark plug you can get in that size which will more than likely be a ngk or E3. The E3's are great plugs I noticed smoother engine idle etc with them especially in 2 strokes.
Better keep it cleaner than a surgeons scalpel with that tiny point of contact or you will get miss fire alot guys they aren't as reliable long term obviously
Also 10 more hp that's mental you won't be able to tell you have done this like saying if you leave your phone at home those weight savings will increase power too weight ratio and you will do power wheelies on your 125cc with ease
Also 1 more thing this is bloody dangerous the size of the gap increases the voltage needed too fire and the time to build that spark alters pre ignition will destroy your engine and later firing will remove hp
For more power on the wheels you have to change the bike with bigger cc . No need to think about small modified thinks . It will not work . Other bike like competition models will please your demands :) Best regards ! :)
leave the spark plug alone, if the bike is not meant to have side spark spark plugs then there is a chance the engine will run hotter and you will burn your valves just like running a lean tune
I dont think cutting a plug does do anything. As long as the fuel gets ignited on time the power pushing the piston down doesnt have anything to do with the spark.
It takes more than just more spark to increase power and the only reason you need more spark is when you make fuel upgrades and air upgrades because with more fuel and more air in order to burn it all correctly you then need a hotter more powerful spark so yes side gapping will help but only if you have increased fuel and air to the point a stock plug cant burn hot enough to burn all the fuel your pumping into. From the looks of it your bike is basically just a off the floor normal stock bike so really all yourr doing is hurting your performance unless you get a bore kit a bad ass carb setup wiith bigger jets and a better air intake set up. Not trying to bash on ya kid just trying to help.
Don’t do what he does he doesn’t know much about bikes he like to ride them cause now he sending bad advice to people that don’t know a lot about bikes there is more ways to add hps to your bike without touching the plug
You have a high compression race bike his is a low compression trail bike yours has little room for error his has a lot that’s a very short explanation or your issue could be completely unrelated so idk your loss I geuss 😢
What happened is you decided to listen to someone who experiments bikes to see what happens! You just wanted power not an experiment so this being said you should ask how to add horsepower properly not do dumb things that cost you! Good luck rebuilding your bike!
If your desperate for more power, and willing to possibly sack your topend. Tweak the pick up sensor mounted on the case and shift it a degree or 2 counter clockwise. I may blow you bike up if your running 87 octane fuel out of the pump. Get fresh 91 but only fill up your gas can after filling you car. About a gallon of 87 will probably sitting in the fuel hose on the gas pump.
91 in a low compression air cooled engine, what a waste. moving the sensor with 91 works better than not moving the sensor with 91 is because 91 burns slower than 87 so needs the spark to happen sooner for proper fuel burn. using high octane fuel in engines that dont need it will only help empty your wallet faster
@@bjorn1583 What your saying is wrong. All because it's air cooled, it's all the more reason to run higher octane. Your forgetting what actually matters, heat. Air cooled motor run far hotter than anything liquid cooled motor. Higher octane fuel has a higher flash point than regular 87. When you're advancing the timing, the motor is going to detonate with cheap fuel. Your just asking to blow up a bike.
@@bjorn1583 and you misread my comment is seems. I'm TELLING him to move the sensor. Not just run 91. You're not really making a point here. You sort of talking out of you A$$
@@ncopp4358 ALL air cooled engines run on low octane fuel for a reason and high compression is what causes low octane fuel to detonate not the timing. I didnt misread your comment but your comment showed you dont know what your talking about and your reply proves 100% without a doubt you dont have a clue on what you are talking about. and you say I'm talking out my a$$, your a joke and always will be and your uneducated comments prove it
Rather go with a multi point spark plug, the gap should be something you don't mess with, just because of that, there are plenty of ways to gain hp and this isn't one of them...
I could not bear to watch at 4:17 all the muck around the open spark plug hole ready to drop right into the cylinder...use compressed air or a soft brush to clean that area before removing plug, please!.
Very Sooty and Black = not a good clean burn.. before it was a very lite brown ashy looking, about as good as it gets. White ashy = lean burn. Basically its not a good mod unless you can get more energy to that plug.
You can not go off that video they were using a plug tester with WAY more power that any bike ignition could ever produce, run the right plug with the right gap and leave it alone.
if youre that needy for more power, then port match intake port to throttle body, and exhaust port to headers, and spen 10 bucks on iridium spark plugs. edit, fix your damn compression!! youll get that 10 hp by fixing your damn motor
Take a bottle put fuel in the bottom so it’s filled with fumes Put any spark in there Kaboom dude The size of the spark matters not the engine specs are where the power comes from. It’s measured Dancing moving around lolol that makes more horsepower lol
Side gapping is used in Racing . High Fuel Ratios and High temperatures .
Side gap plugs dissipate heat from themselves quicker to avoid overheating and Melting the Electrodes .
The Plugs do NOT make more Power . Even a High-end MSD ignition doesn't . What happens is MISFIRES are eliminated .
Changing the gear ratio is the best and easiest way to make a small cc bike feel more powerful.
many years ago I had a single cylinder 185 suzuki 2 stroke that had 2 spark plugs in the head so if one fouled you could swap the lead to the other one for a fresh plug. But what I did was add another coil & lead to the second plug so both were firing & it made a huge difference way more low down power & always started so easy.
Not sure if you know this but the second sparkplug hole was originally for a decompression for easier start then it was found they didn't really need it so it was used as a spare plug,interesting how you hooked both up though that's pretty cool.
the steady spark is because it connects the closest points. with the original the surfaces are parallel and spark can form anywhere between the parallel surfaces but will have the same power every time. With the side gap the location of the spark is constant and will wear the side of the electrode then the gap will increase. It is possible the flame will travel slightly better because it can spread in all directions initially but hard to tell if it helps without clear tests
Idk why people write so much hate to you. I have a 50cc and I am just like you, I like trying homemade things to make my moped better. I love your videos!
Mess with the carb a little bit. That screw on the side where you can change the idle, idle up a tad and try that
I agree but its fun watching this experiments :)
For all the comments putting down his testing. This is simply some of the ways you get in the fast lane. Test and trail. If you don't like it just stay over there in the slow lane👍
why cut it just open the gap more
@@user-jk9tr2gm5p because it fires more when it's off to the side, and it let's the fire hit the fuel better when it's not being covered.
There are weird spark plugs out there like Brisk, that one doesn't have a hook. I tried it and it works like a spark plug.
David Vizard covered this topic in a video as well as writing about it in one of the books he has written.
They prob side gapped plugs too run shit loads more fuel without fouling plugs guessing
I've been grinding my spark plugs since the 1960s, except the Iridium plugs. [Dodge D-50 2.6 5 spd.]
I VASCAR tested 1/8 mile of 3 runs (averaged) & went from 14.25 to 13.75 seconds. My mpg's also went up. __ CHEERS 😉
I side gap my 2 stroke lawnmower spark plug, it stops fouling. My nieces husband came for a visit, his car wouldn't start so I removed the plugs, the outer electrode was almost completely burnt off so I gapped what was left re fitted them and it ran.
love you vids zoomin' ❤
Side spark in racing has nothing to do with the ground terminal blocking the combustion. When the spark "dances" it changes length and there fore temp. Racing calls for consistency of high performance precision at the cost of longevity. You electrode and ground post are going to concentrate all of the wear in one "laser" spot increasing gap wear quickly out of optimal range. Not an issue if you change them after every race.
The ignition has to be able to create the spark longer too. I used side gapped plugs in 2 stroke engines turning 20,000 rpm. But the pumper carbs had externally adjustable low and high speed jets .The plugs were alot foul resistant in 2 strokes for sure
For you to get anything from the plug if you got more consistent spark
you would need to alter the gas and air mix because it most probably running lean and the plug is burning it up quickly and if that helps but doesn't solve problem change jets size for more fuel
Mazda rotary engines use a triple ground. I have felt a change in performance using those years ago. They are more of a side shooter.
Good info dude! Now do research on indexing spark plugs. If you index them, you'll get the electrode facing directly at the fuel air mix when it enters the engine making even more power
You should make a double tip/ gap spark plug and see if it's better
You can try to advance the cam by 1 tooth or 10 degrees. The stator coil pickup might be able to be modified so you can advance the timing a few degrees
Good answer it's unbelievable just how many people that will talk like they know everything but don't know anything. Reading your comment let me know that they're still ppl who have done it and know what to do.
If I had that xr100 and was desperate for more power I'd sell it and get the 400 as a step up or the 650r which is in my opinion the best enduro I've ever owned wish Honda would make them again
i agree. even a 200 would be a world of difference
Too small of a motor to notice any power gains using the butt dyno. Sounds like it ran good though. Cool vid...👍
45° cut is ideal . Can not rEcall if it's right or left .
Lov your vids
Mercury boat, spark plug is what you need
looking at your spark plug its fooled you need to adjust your mixture also keep the plug standard with the correct gap and also your carb is junk because the carb has the choke butterfly in the way at the rear that stops power chuck in bin by a cheap molkt brill carb that will fit and finaly change your sprocket up a tooth for higher top end 1 tooth less for more acceleration but less top end , you got to get the combos right .
Put a iridium (good Ngk) and see the difference in perfomance.
In our 1000 HP BBC, we closed the gap to about .025"...
Find your high speed best mixture by getting some jets that are a little bigger and a little smaller than what you have stock. With no other mods on the bike tuning the carb will be best bet. Do the high speed tuning to determine jet size at full rpm. I will assume you need a smaller jet than what you currently have. Then set that needle up a position at a time until your revving from idle on up is the quickest it can be, ie, no bog. Do this and you will be surprised I think. Maybe after getting good air fuel ratios you can play with modded plugs. Good luck!
The only way more spark will give you more power is if you’re dumping more fuel than can burn with original spark. But more fuel can’t burn without more air.
The key to horsepower is air. That’s the first thing you need to gain power. Once you get more air in it you can add fuel. And unless you’re dumping a lot more fuel in it I’m sure your original spark can handle it. It is fun to try though lol. Keep at it young man.
I did this with a half clapped out plug on my Stihl backpack blower the other day and no shit..... Starts quicker every damn time now. One pull, always.
Different spark plug gaps subtlety alter the timing of the spark. And different timing affects power output. That's a fact.
Just use a twin pointed sparkplug like Denso TT. They won't let the spark dance at the edge and destroy it.
Guys don’t do dumb shit with your spark plug, you only have 1 of 2 things, normal combustion and abnormal combustion
If you have a problem then modifying a spark plug will not solve the problem
An electrical engineer figured this out and RUclips can’t make it better, if this mattered NGK would just make this plug and sell it to you
BTW did you notice the spark jumping to ground without crossing the gap first, this plug has a carbon track on the porcelain which is likely the problem
On a small bike engine with,let’s be fair, a small horsepower figure, there’s never going to be an magical and noticeable gain from a spark plug. It’s either going to work or not. What you’d be better doing is playing around with the timing of the spark and seeing what you lose or gain across your power curve. But if you love that bike and enjoy tinkering, drop in a larger lump. 👍
I'd like to see the video where he's replacing his valves hahaha
where do ya live ? my buddy has a motorcycle dyno
Keep on trying. Don't stop your curiosity. That's how we keep inventing ,thinking outside the box imagine if we stop after the cave man finished with the stone wheel.😅😅😅 thanks for your time to show the difference it makes just by simply cutting the gap a little at a time .
Just low on blinker fluid" 😂
If you want more power, get better exhaust flow better air flow into the engine and more fuel, bigger exhaust, bigger carb for starters
It has more power
But not to much when u cut it
Bro you just CANT get more power by increasing the Electricity! You need MORE Fuel and MORE oxygen! NOT ELECTRICITY
how about... stronger fuel pump, better and more powerfull injectors (better spray), better RAM intake AND better electricity? A better ( bigger ) spark will help igniting cleaner i guess.
so maybe.. instead of cutting the spark plug, he could bend the sparkplug so the metal part stands up more. So the spark needs to travel further and deeper into the engine.
@@Satori-Automotive I disagree my friend
@@Satori-Automotivetheres no fuel pump or injectors or short ram (seems like you are talking about cars) however he could get a bell intake or velocity stack for the carb. He could get a racing version of his ignition coil, maybe racing CDI, spitfire cable and one of those iridium spark plugs which give a "laser beam" spark. More air and fuel will give more power so a cleaner flowing exhaust and exhaust tube with the power bomb thing would be nice. As well as bigger valves and head porting. He could also raise the compression ratio.
Edit: custom camshaft with more opening and overlap would yield results and he could also mess with spark timing and carb tuning
@@Satori-Automotivebetter ram? 16gb of ddr4?
It can make more power, if it burns more of the air/fuel.. no engine burns 100% but the closer you get the better.
More burned fuel = more power.
But most likely not enough to worry about.
I'm no expert but in order to gain power from firing you would have to change your stater and CDI and higher voltage coil. You can buy high performance cdi boxes and they will boost engine performance. I put a high performance cdi on my son's pit bike and it made a world of difference in the throttle response and cruising. It was so much smoother than the factory when I first started it I had to adjust the idle down cause it was idling 6 to 800 rpm more with no fuel change and when you held it at a constant rpm speed it so smooth. Also you can buy offset keyways to advance your timing. Just wanted to share for all the keyboard warriors saying that spark won't help performance clearly never set the timing on a small block or anything for that matter. Timing and spark are very important you could have the biggest baddest built engine in the world with the biggest fuel system but without proper timing and spark you have the worst performing engine. Also if you want better spark don't cut your plugs just go to the Auto parts store and get the hottest spark plug you can get in that size which will more than likely be a ngk or E3. The E3's are great plugs I noticed smoother engine idle etc with them especially in 2 strokes.
Better keep it cleaner than a surgeons scalpel with that tiny point of contact or you will get miss fire alot guys they aren't as reliable long term obviously
Also 10 more hp that's mental you won't be able to tell you have done this like saying if you leave your phone at home those weight savings will increase power too weight ratio and you will do power wheelies on your 125cc with ease
Also 1 more thing this is bloody dangerous the size of the gap increases the voltage needed too fire and the time to build that spark alters pre ignition will destroy your engine and later firing will remove hp
lol
smaller area=faster erosion.
4:29 if you can start it like that, don't mind about your spark.
For more power on the wheels you have to change the bike with bigger cc . No need to think about small modified thinks . It will not work . Other bike like competition models will please your demands :) Best regards ! :)
Excellent 👌👌 job
leave the spark plug alone, if the bike is not meant to have side spark spark plugs then there is a chance the engine will run hotter and you will burn your valves just like running a lean tune
Buddy this bike has ran on straight octane booster he’s trying to kill it
How would you burn a valve in a 2 stroke? Asking for a friend 😅
@@ZafiraSteve thats a 4t i think
Stay in the slow lane bro. Cuz this some of the ways you get in the fast lane
@@ZafiraSteve most 2 strokes have valves plus it sounded like a 4 stroke
Grinding material spark plug just make it Last less you expose normal metal then so it work even worst now
now if you paint the plugs bright pink and put some plastic over the electrode a tank of petrol will last forever
Turn the idle up on the bike bro
Winding the idle screw in will lean out air fuel mix ,Better of rich on idle so don't lean out on Deceleration.
I'm sorry I don't see much of a result look like the same thing to me
Why not just get an iridium plug you can gap it probably and get a sharper spark
Put some shinko 705’s on the katana and rip it off-road
Port and polish the cylinder
I dont think cutting a plug does do anything. As long as the fuel gets ignited on time the power pushing the piston down doesnt have anything to do with the spark.
It takes more than just more spark to increase power and the only reason you need more spark is when you make fuel upgrades and air upgrades because with more fuel and more air in order to burn it all correctly you then need a hotter more powerful spark so yes side gapping will help but only if you have increased fuel and air to the point a stock plug cant burn hot enough to burn all the fuel your pumping into. From the looks of it your bike is basically just a off the floor normal stock bike so really all yourr doing is hurting your performance unless you get a bore kit a bad ass carb setup wiith bigger jets and a better air intake set up. Not trying to bash on ya kid just trying to help.
put a 28mm carburetor and put a 17 teeth primary sprocket and you will Rock 🎉
Thanks darth vader 💀
Hope you don't melt your piston.
Hey man I watched your video and did this and now my bike is siezed.. what happened bruh
Can’t believe everything you see dummy 😂😂
Did you not see that it wasn’t working for him? Yall are stupid asf
Don’t do what he does he doesn’t know much about bikes he like to ride them cause now he sending bad advice to people that don’t know a lot about bikes there is more ways to add hps to your bike without touching the plug
You have a high compression race bike his is a low compression trail bike yours has little room for error his has a lot that’s a very short explanation or your issue could be completely unrelated so idk your loss I geuss 😢
What happened is you decided to listen to someone who experiments bikes to see what happens! You just wanted power not an experiment so this being said you should ask how to add horsepower properly not do dumb things that cost you! Good luck rebuilding your bike!
Try 3 points plug. Bro
Take it in and have a Dino B4 and after
RIP piston.
To inform you
After that you will have starting problems
The same is at low revs
If your desperate for more power, and willing to possibly sack your topend. Tweak the pick up sensor mounted on the case and shift it a degree or 2 counter clockwise. I may blow you bike up if your running 87 octane fuel out of the pump. Get fresh 91 but only fill up your gas can after filling you car. About a gallon of 87 will probably sitting in the fuel hose on the gas pump.
91 in a low compression air cooled engine, what a waste.
moving the sensor with 91 works better than not moving the sensor with 91 is because 91 burns slower than 87 so needs the spark to happen sooner for proper fuel burn.
using high octane fuel in engines that dont need it will only help empty your wallet faster
@@bjorn1583 What your saying is wrong. All because it's air cooled, it's all the more reason to run higher octane. Your forgetting what actually matters, heat. Air cooled motor run far hotter than anything liquid cooled motor. Higher octane fuel has a higher flash point than regular 87. When you're advancing the timing, the motor is going to detonate with cheap fuel. Your just asking to blow up a bike.
@@bjorn1583 and you misread my comment is seems. I'm TELLING him to move the sensor. Not just run 91.
You're not really making a point here. You sort of talking out of you A$$
@@ncopp4358 ALL air cooled engines run on low octane fuel for a reason and high compression is what causes low octane fuel to detonate not the timing.
I didnt misread your comment but your comment showed you dont know what your talking about and your reply proves 100% without a doubt you dont have a clue on what you are talking about.
and you say I'm talking out my a$$, your a joke and always will be and your uneducated comments prove it
@@ncopp4358 telling a transport engineer he's talking out his a$$ when everything you have said is completely wrong, your a joke
Put iridium plug in it for more power
Pipe jet kit and spark advancer
Use iridium plugs...
I hope he never takes off his helmet
roger that
if you need more power get go green and get a kx 500
missed split fire type
Run AV Gas in it.
Rather go with a multi point spark plug, the gap should be something you don't mess with, just because of that, there are plenty of ways to gain hp and this isn't one of them...
Kid feathering that clutch or power shifting
Powershifting
Kind of the same thing but rpm gotta be right on every shift
He going to have to put clutches in that after all that slipping while shifting
I could not bear to watch at 4:17 all the muck around the open spark plug hole ready to drop right into the cylinder...use compressed air or a soft brush to clean that area before removing plug, please!.
Keep.
The gap to spec or you will start frying electronics
Very Sooty and Black = not a good clean burn.. before it was a very lite brown ashy looking, about as good as it gets.
White ashy = lean burn.
Basically its not a good mod unless you can get more energy to that plug.
The whole rationale here seems to be nothing more than supposition but with no proof, sounds ropey to me
Works better on 2 strokes
Try Arc lighter plasma
You can not go off that video they were using a plug tester with WAY more power that any bike ignition could ever produce, run the right plug with the right gap and leave it alone.
A mi me funciono le dio más reacción de aceleración y un poko más de potencia yo tengo una moto 2 tiempos
Change coil overs instead
that would not give it more power
this was not a lame video
Just use Coil of Suzuki A100.
if youre that needy for more power, then port match intake port to throttle body, and exhaust port to headers, and spen 10 bucks on iridium spark plugs.
edit, fix your damn compression!! youll get that 10 hp by fixing your damn motor
I opened the gap on my plug from .025 to .040 & gained a little more torque. More than I was expecting yo for sure
If an engine was meant to have a side gap plug it would have been designed for it.
agreed. dont you love when people think they can improve over all the engineers that built something.
If it were that simple to get extra BHP for nothing, you don't think the big 4 bike manufactures would of done this years ago?
First rule in life if it runs fine don't fix it. If you need more power get a bigger bike. And why do you hide your face😮😮😮
Run crude oil in your bike
ya lets see it
It would simply blow
@@ncopp4358 never know with the old hondas lol and it would be funny
Just get a bigger motor for more power or you can modify the motor you have if you know what you are doing.
Why is the fool wearing a helmet, side gapping is a total insane idea.
Really
Take a bottle put fuel in the bottom so it’s filled with fumes
Put any spark in there Kaboom dude
The size of the spark matters not the engine specs are where the power comes from. It’s measured
Dancing moving around lolol that makes more horsepower
lol
this kid does everything we want to try bot are too scared to do
First question before I ask any others is why are you doing this video with your helmet on???😂 Something fishy going on Willis!!!😂😂😂😅
Just get a bigger bike.
the mixture is to rich!!