Warning (which should have been verbalized): Before removing the screen, go to the end of screen removal in the video where you can see the back of the display. Note that there are flex circuits stuck to the back of the screen. There is a large one at the top with a large connector that goes out to the side and there is a skinny flex circuit that runs from the center (button) up about 2 inches. You cannot shove a card in deep in any of these areas or you will rip the delicate flex boards, especially the large on at the top. Note that in the video, they work from the bottom (side not absolute bottom) and pry the screen off from the bottom so that by the time you get to the delicate large circuits at the top, you may not need to use the cards or pics to break the glue. You might be able to just pry it apart at that point, avoiding hitting that circuitry. You might have to reheat the are repeatedly, front and back, to get the glue to let go easy enough so that you do not break the screen trying to pry it open. But back at the bottom where you start, you need to also be careful to not go too deep with the cards. You are safe in the area where they show you start... working a card under that metal frame. That area has no flex circuits. but that is the only area that has no flex circuits. In all other areas you can only go in shallow with a card or pic, if at all. With all that in mind, maybe make a little sketch of how that display looks from the back, and use that sketch for your strategy. And re-watch this part of the video (screen removal) with all that familiarity now. Now the details of penetration etc will make more sense. Doing this a second time would not be so hard, but on first try, you will probably destroy the flex circuits unless you pause when it is time to remove the screen, and accept that you are not close to done yet. You will have to take some time and strategize and watch that part of the video more than once. I gave the video a like, but then a dislike when I finally finished and had destroyed my flex circuits glued to the screen. There should have been emphasis / a caution about this. YOU DO NEED A HEAT GUN, though I have seen other videos where they use some kind of solvent to weaken the glue. I think the solvent was called "KONTACT PCC". They bleed the solvent into the cracks, and then add more solvent once there is a wider crack. You should look for that video if that is going to be your tactic. But this heat gun method almost worked for me.
Yes. I guess there is a huge failure rate when it comes to these flex circuits. I thought I had mine apart clean but after close examination I cut mine slightly during disassembly. Thanks for the heads up.
Great video! For everyone who just wants to charge their phone without fixing it, my charging port on my Galaxy S7 Edge went bad and I bought a wireless charger. It works perfect.
Dude I don't know why this vid doesn't have more views. Awesome job!!! Over vids say you can't replace USB port without breaking screen. Thanks you really made my weekend!
Have you tried?? I'm in this it's been like 8 hours.... That glue... with a playing card!?!?... I am at it with pics and an exacto and I am having a hell of a time... Think I'll go with xav_B's idea.... Thanks anyway for the vid...
I recently replaced my s7 edge screen and audio jack, but the audio jack is still unresponsive. When I plug headphones(they're not faulty headphones) in, the sound comes out of the phone speaker. Could this be a problem with the charging port part? Also the "recent button" is also non responsive. It was working before, but I might have damaged it. There are no cracks or tears that i have noticed.
, how much do they usually charge to have that fixed I'm currently having this problem and only can use the wireless charger and it sucks cuz it's kind of slow even if it's a fast wireless charger
Hello, R3drift! Here in Spain is about 59 euros www.movilone.es/reparar-conector-de-carga-samsung-galaxy-s7-edge Have a nice day and thank you for asking!
thanks ,your video is very helpful, which type of Glue do you use? my S7 Edge does not work because of water, how can I be sure which one of these is damaged/ charging port, Battery or main board , I mean to test??? thanks anyway
Hello, Eric! Thank you for your comment. The answer is : No.Once you open the phone it is no longer waterproof.In any case it is not advisable to submerge it, because submersible devices arrives in our workshop, with damage on the motherboard because of water, liquids ...Have a nice day www.movilone.es
I had a new phone unopened and when it fell in water just for a few seconds it damaged the motherboard and eventually the screen went also. These items are not waterproof no matter what they say. It is logical as there are holes for charging, ear phones, sim card, speakers etc. that cannot be fully waterproof. Keep all electronic equipment away from water!
Nice vid, but I have one concern....you did show if it was charging after it was all put together. I could see that there was no indication that it was "charging". I stopped the vid at 21:10 and there was no "charging" indicator on the battery indicator. So, this doesn't show if you repaired the issue with the charging port or not....just saying....
Hello, M.Rey Sanchez! i have thought that the blue light is an indicator that the phone is charging...you might be right and i should teach more time the fact that is charging. Have a nice day and thank you www.movilone.es
I do repairs on the side, I'm a certified pc tech and have a few certifications as a Network Engineer....so, I "dabble" in repairing cell phones and tablets for friends and some friends of friends. I've always seen the "lightning bolt" showing that the item is charging, but I didn't see the "lightning bolt" when you showed it all put back together. This is why it has me wondering if it was charging. After you did the repairs, did it charge?? I'm in the process of repairing my wife's Samsung Galaxy S7 Edge....
M. Rey Sanchez maybe the charging port was defective but is honestly not the point, if you can take the screen out like that you’re really good. I’ve been a tech for years and sometimes I struggle on taking the screen out. The back method is a way new approach which is a amazing.
hey what is the white and blue cable one of them is broken in my edge, first day there was no connection problem but next day i have lost network connection. is it antena, if it is why it is two item.
You have crazy skills to remove the screen without breaking it! Are you able to do that consistently? If so, do you want to look into repairing the pink line issue? I believe all you need to do is once the screen remove, put adhesive or tape onto the Display's ribbon cable and the pink line will be gone.
nie, bo to brudas i udaje że coś potrafi zrobić. jakby tam pies nasrał to też by mu nie przeszkadzało. film do dupy,,, tak jak powiedział johnm trzeba grzać i grzac, cały telefon a nie bawić się w idiotę. ekran mozna rozłaczyć tylko termicznie delikatnie, powoli a nie wpychać jakieś papierowe śmieci miedzy ekran a chasiss. brak informacji o kleju, brak informacji o tym aby uważać i nie stosować zadnej siły do oddzielania ekranu. grzanie to podstawa. nie ma informacji jakiego kleju uzywać. rozłożyć telefon może kazdy głupek.
Good job, but it's much easier to replace just the charging port, not the entire dock connector. You save a lot of time and avoid the risk of braking the LCD.
Hello, Alexandru! in the repair channel we have several tutorials on how to repair the charging connector, this is one of the modalities we present :) Thanks for watching!
Amazing guy, very patient & resilient! But, no, thanks, I will pass. I can still charge and use my phone by taping the cord's end (to take the free movement/slack away) just after being inserted into the port. Yes it is non-sense laborious to do that but what you have gone thru to change the port is a complete removal of all components from the casing. Ayayaya, this is crazy... should be avoided at any cost.
Thank you for your comment! it's not actually one of the easiest repairs I've ever made. At home and without tools it becomes ... even more difficult. Thanks for watching!
I wayched all the video because I want to know what makes the cellphone water proof, I got one I scare about get it into the water but at the same time I want to do it because i had a s5 and I remember I got it into water and was awesome, can you help me with any answer or something?
Sorry, Jes! Try to find it on Aliexpress because i can't recommend you ...If it was here, in Spain or Europa, i m almost sure that i could helped you more....Wish you good luck!
@@MovilonePhoneRepair my S7 Edge won't charge, i replaced the battery but still won't charge, i used different cords but still won't charge even the wireless charger, do you think the charging system is the issue? same as the video above?
They didn’t mention this in the video, but I want you guys to be careful when taking off the screen and going through the adhesive, don’t poke too far in near the lock button because that’s where the cable for the LCD is and it’s very sensitive, i accidentally ripped mine because I didn’t pay attention to how close the cable was to the edge. Not blaming the video maker, it was my mistake, just don’t want anybody else to make it and have to spend $150 for a new LCD
That is impressive, but so much work. I think I'll just live with mine and use some tape to hold the cable in the port just right until I can buy a S9.
Sir I have Sam s7 edge for which normal charging is working, but fast charging and USB connection is not working, I've also checked with another device for which fast charging is working with same cables
Hello, Prakash! According with the information that you provide, i Thing you have a problem with the charging conector and the tracia that aré responsible for the computer connection aré damaged! Thank you for asking! Have a nice day
Hello, Farzana! In this case, charging connector is a flex that has other accessories too, buttons, microphone ...Any informacion you might need, i m at your disposal!Best regards www.movilone.es
Damn, the stuff that happens around 11:20 is pretty crucial. Just broke my S7 screen into 100 pieces, phone goes in the trash. Wish I knew where in your channel the video without removing screen was before following this guide. Can't find it. Oh well, have to use a new phone instead!
Hello, Karl! I really feel bad for you; this is the link from the another method that I used without remove the screen ruclips.net/video/t14Ae_xysmY/видео.html Also, I have to tell you that you need some experience, too...it s not easy to repair it and some good tools! Best regards
Hello, Farhaan! yes, you can do it without removing the screen, informó act I ve got another repair in my youtube channel were I m doing this repair in that way. Thank you for asking! Best regards
It charges without problems with a Wireless Charger. I only have a slow, 5W Wireless Charger which charges my phone in about 5 hours... But I can still connect it to PC and transfer files. I only repaired an iPhone 6 and a LG G4 before, and to get inside I just needed a screwdriver... But here, It's a little bit more complicated 😂.
Hello, Arshad!i ll just attach you the link of this repair: www.movilone.es/reparar-conector-de-carga-samsung-galaxy-s7-edge If you have any question, please let me know! Have a nice day! www.movilone.es
Hello, Krishna! We can do it, don t doubt it, but we are from Spain, so if you contact us from outside the national territory, please use the form contact on our web site www.movilone.es Thank you and have a nice day!
i have replaced so many screens and ports over the years. I told my friend I would fix her port and this scared the sh*t out of me. Damn it this is going to suck balls.
@@MovilonePhoneRepair I looked it up cause i work at a repair shop and im gonna try to start doing the charge ports. Super cool idea to work the bottom half first, thanks for the good advice
Les ingénieurs Samsung ne sont pas compatissant, ils auraient pu nous faciliter ! Ca aurait été plus commode pour nous "les Clients". Autant changer de téléphone
They really don't want you to take apart these phones do they. Honestly,my patience would probably run out and I would smash the phone into a million pieces.
holy shit thatts too much. my phone's charging port does not work so i was thinking of replacing it but after seeing this video , nooo man. no. im good with wireless charging
:) Yunus!! You've made me laugh :) Is better for you to take it to specialized technical service, the wireless charge ... what will cause that in time it damages the battery, the duration of the load is not the same ... let's say it is an option at the moment ... Best regards!
Lol I use the Samsung Wireless port but I am still deciding on whether to risk to fix the port or not because it takes like 3 hours for my phone to charge with the wireless port.
Chris, i m so sorry to hear that! If it seems to you, so complicated you should let it on hands of some technical service from your area.... Wish you good luck!
@@MovilonePhoneRepair all good, it happens. Was worth a try, it needed to be fixed one way or the other and the repair shop said it would almost definitely break the screen anyway
Chris, there is a tool with which we open these devices without breaking the screen ... but well, the fact is done ... so, the next :) more carefully!Best regards
@@MovilonePhoneRepair the same issue lol, wish u would have mentioned that do not go from the button of the screen with playing cards. it went in between the digitizer and that screen paper. what is that tool u mentioned?
Please remove the baterry flex firsly you can't work like that please do a better job you can't desconnect de lcd flex wen the battery is still connected
*✅ Tools HERE* 👉👉 https:movilone.eu
notification song name?
Warning (which should have been verbalized): Before removing the screen, go to the end of screen removal in the video where you can see the back of the display. Note that there are flex circuits stuck to the back of the screen. There is a large one at the top with a large connector that goes out to the side and there is a skinny flex circuit that runs from the center (button) up about 2 inches. You cannot shove a card in deep in any of these areas or you will rip the delicate flex boards, especially the large on at the top. Note that in the video, they work from the bottom (side not absolute bottom) and pry the screen off from the bottom so that by the time you get to the delicate large circuits at the top, you may not need to use the cards or pics to break the glue. You might be able to just pry it apart at that point, avoiding hitting that circuitry. You might have to reheat the are repeatedly, front and back, to get the glue to let go easy enough so that you do not break the screen trying to pry it open. But back at the bottom where you start, you need to also be careful to not go too deep with the cards. You are safe in the area where they show you start... working a card under that metal frame. That area has no flex circuits. but that is the only area that has no flex circuits. In all other areas you can only go in shallow with a card or pic, if at all. With all that in mind, maybe make a little sketch of how that display looks from the back, and use that sketch for your strategy. And re-watch this part of the video (screen removal) with all that familiarity now. Now the details of penetration etc will make more sense. Doing this a second time would not be so hard, but on first try, you will probably destroy the flex circuits unless you pause when it is time to remove the screen, and accept that you are not close to done yet. You will have to take some time and strategize and watch that part of the video more than once. I gave the video a like, but then a dislike when I finally finished and had destroyed my flex circuits glued to the screen. There should have been emphasis / a caution about this. YOU DO NEED A HEAT GUN, though I have seen other videos where they use some kind of solvent to weaken the glue. I think the solvent was called "KONTACT PCC". They bleed the solvent into the cracks, and then add more solvent once there is a wider crack. You should look for that video if that is going to be your tactic. But this heat gun method almost worked for me.
Yes. I guess there is a huge failure rate when it comes to these flex circuits. I thought I had mine apart clean but after close examination I cut mine slightly during disassembly. Thanks for the heads up.
Where do you get the glue to glue the screen and back again?what kind of glue he use?
guys i have a S7 Edge too that won't charge, is this the issue too? replace the charging system? any comments can help
Thanks for the warning, I was about to rip the cables😅
Great video! For everyone who just wants to charge their phone without fixing it, my charging port on my Galaxy S7 Edge went bad and I bought a wireless charger. It works perfect.
I think you're the only one I've seen come through the back like that what a great idea!
:) Thank you for your comments!
And all this time i thought it's impossible to disassemble the screen without cracking it
Great job man,i learned a lot!
Many thanks for your great video, which glue do you use please?
Dude I don't know why this vid doesn't have more views. Awesome job!!! Over vids say you can't replace USB port without breaking screen. Thanks you really made my weekend!
Thank you very much for the comments :) Impossible doesn't exist!
www.movilone.es
You don't need to remove the screen to change the port, desolder old one and solder new one
Tal Robinson rtyfg
Have you tried?? I'm in this it's been like 8 hours.... That glue... with a playing card!?!?... I am at it with pics and an exacto and I am having a hell of a time... Think I'll go with xav_B's idea.... Thanks anyway for the vid...
Broke my Digitizer Display. Wished I had read John M comments. Desolder seems better way.
Thank you so much! Now i can repair my own phone. Question though, why did you have to use a heat gun at 15:30?
Hello and thank you for your comment! The heat gun i used because the glue is more efficient wih the heat.Have a nice day!
www.movilone.es
Sir I have no words to give complement to this amazing work. Hats off.
lol ok i need to just buy a new phone
same lol
Buy a wireless charger
This is the best step by step breakdown of a s7 egde, wonderful video bro.
Thank you,Swiffcash for your comment! Best regards
+
This work is very difficult for beginners.
..
Thank you
Sw, i understand you perfectly! Thanks for watching! Best regards
I recently replaced my s7 edge screen and audio jack, but the audio jack is still unresponsive. When I plug headphones(they're not faulty headphones) in, the sound comes out of the phone speaker. Could this be a problem with the charging port part? Also the "recent button" is also non responsive. It was working before, but I might have damaged it. There are no cracks or tears that i have noticed.
, how much do they usually charge to have that fixed I'm currently having this problem and only can use the wireless charger and it sucks cuz it's kind of slow even if it's a fast wireless charger
Hello, R3drift! Here in Spain is about 59 euros www.movilone.es/reparar-conector-de-carga-samsung-galaxy-s7-edge Have a nice day and thank you for asking!
thanks ,your video is very helpful, which type of Glue do you use?
my S7 Edge does not work because of water, how can I be sure which one of these is damaged/ charging port, Battery or main board , I mean to test??? thanks anyway
Hello great work please do I need to replace the screen while changing the charging port..thnk
Hello, Deborah! it s not necesary if the screen works. Best regards
Awesome work man! One question, does the glue you added (B7000) makes the phone waterproof again?
Hello, Eric! Thank you for your comment. The answer is : No.Once you open the phone it is no longer waterproof.In any case it is not advisable to submerge it, because submersible devices arrives in our workshop, with damage on the motherboard because of water, liquids ...Have a nice day
www.movilone.es
Thanks man ! :)
Fell out my boat in salt water s7 in my pocket, this 1 year ago still works fine.
I had a new phone unopened and when it fell in water just for a few seconds it damaged the motherboard and eventually the screen went also. These items are not waterproof no matter what they say. It is logical as there are holes for charging, ear phones, sim card, speakers etc. that cannot be fully waterproof. Keep all electronic equipment away from water!
You are too good at explaining others get lost in the dialogue instead of teaching. You are very good!
Nice vid, but I have one concern....you did show if it was charging after it was all put together. I could see that there was no indication that it was "charging". I stopped the vid at 21:10 and there was no "charging" indicator on the battery indicator. So, this doesn't show if you repaired the issue with the charging port or not....just saying....
Hello, M.Rey Sanchez! i have thought that the blue light is an indicator that the phone is charging...you might be right and i should teach more time the fact that is charging. Have a nice day and thank you
www.movilone.es
I do repairs on the side, I'm a certified pc tech and have a few certifications as a Network Engineer....so, I "dabble" in repairing cell phones and tablets for friends and some friends of friends. I've always seen the "lightning bolt" showing that the item is charging, but I didn't see the "lightning bolt" when you showed it all put back together. This is why it has me wondering if it was charging. After you did the repairs, did it charge?? I'm in the process of repairing my wife's Samsung Galaxy S7 Edge....
:) Yes, M. Rey Sanchez. It was charging; i assure you. Best regards.
M. Rey Sanchez maybe the charging port was defective but is honestly not the point, if you can take the screen out like that you’re really good. I’ve been a tech for years and sometimes I struggle on taking the screen out. The back method is a way new approach which is a amazing.
It shows 8 hours 10 mins charge time remaining. Don't know if that is the shit charger or a bad connection on port
Amazing job!! I am about to attempt this now..... Hopefully I can be as good as you
Thank you, Chelsea for watching! Wish you good luck Best regards
hey what is the white and blue cable one of them is broken in my edge, first day there was no connection problem but next day i have lost network connection. is it antena, if it is why it is two item.
You have crazy skills to remove the screen without breaking it! Are you able to do that consistently? If so, do you want to look into repairing the pink line issue?
I believe all you need to do is once the screen remove, put adhesive or tape onto the Display's ribbon cable and the pink line will be gone.
Thank you, Tzontlilic! I ll try it next time with some screen.Thank you for your idea.Best regards
www.MovilOne.es
Its not needed to remove the old glue before regluing back in place?
nie, bo to brudas i udaje że coś potrafi zrobić. jakby tam pies nasrał to też by mu nie przeszkadzało. film do dupy,,, tak jak powiedział johnm trzeba grzać i grzac, cały telefon a nie bawić się w idiotę. ekran mozna rozłaczyć tylko termicznie delikatnie, powoli a nie wpychać jakieś papierowe śmieci miedzy ekran a chasiss. brak informacji o kleju, brak informacji o tym aby uważać i nie stosować zadnej siły do oddzielania ekranu. grzanie to podstawa. nie ma informacji jakiego kleju uzywać. rozłożyć telefon może kazdy głupek.
Good job, but it's much easier to replace just the charging port, not the entire dock connector. You save a lot of time and avoid the risk of braking the LCD.
Hello, Alexandru! in the repair channel we have several tutorials on how to repair the charging connector, this is one of the modalities we present :) Thanks for watching!
Amazing guy, very patient & resilient! But, no, thanks, I will pass. I can still charge and use my phone by taping the cord's end (to take the free movement/slack away) just after being inserted into the port. Yes it is non-sense laborious to do that but what you have gone thru to change the port is a complete removal of all components from the casing. Ayayaya, this is crazy... should be avoided at any cost.
Thank you for your comment! it's not actually one of the easiest repairs I've ever made. At home and without tools it becomes ... even more difficult. Thanks for watching!
What is the yellow glue he is using ..
Or is a cleaner
At the end of this ideo, i m using a glus, the B7000 one. I recomended! Best regards
www.movilone.es
Much thanks !
You guys are wonderful. ...
i noticed u were using 2 different types of adhesive on the front and black glass what kind of adhesive is that?
What are the bits that curl around to the front glass? Do we really need them? ✂️✂️✂️
Those bits work the 2 front buttons and are removed after the screen is removed as they are connected to the charging port board Hope this helps
What's the temperature are you applying? 60 C or 100 C for back cover removal? and for the Lcd ? Thanx in advance
Hello, Amin!About 80-90 degrees. Thank you for asking! Best regards
thanx a lot
Thank you, too Amin for watching! Have a nice day
This is such a challenge to get done but i will try it just please tell me can i use a hairdrieer to remove the back plate and the screen
You guys deserve a complete Like..
There you go (y)
Thank you, Eazy Techno! :)) Best regards
What glue are you using?
Hello. I have put B7000.
I wayched all the video because I want to know what makes the cellphone water proof, I got one I scare about get it into the water but at the same time I want to do it because i had a s5 and I remember I got it into water and was awesome, can you help me with any answer or something?
You must remove screen also?? Wust be way better to use soldering instead of stressing the screen and maby waterproofing even more.
Hello, Yngve!This is a way to repair it but there are more ways to do it too.Have a nice day!
www.movilone.es
I'd rather not risk damaging the display 😅
Could this repair be done without the glue just heat?
Does anybody know where can i find the just the black plastic that cover the back and menu bottom that goes on the lower part of the screen?
Jes, do you contact us from Spain?Because i can help you with some links... Let me know! Best regards
@@MovilonePhoneRepairI'm from the U.S.
Sorry, Jes! Try to find it on Aliexpress because i can't recommend you ...If it was here, in Spain or Europa, i m almost sure that i could helped you more....Wish you good luck!
Will this fix "USB device not recognized" in Windows 10? I installed the Samsung drivers and am using a Samsung cable already.
Uffffff que laburo viejo te felicito por la prolijidad 👌
Hola, Javier! Gracias :) Un saludo cordial
I lost one of the two screws holding the usb port...
My buttons came without adhesive on...
Thank you! You made this easy peasy.
Carter C, thank you for watching and for your comment, too! Best regards
Great video, nice and close to view. The battery removal with the playing card was great.
Others tend to pry it up with tools.
Cheers
Thank you, too Gazman100 for watching this tutorial! Best regards
@@MovilonePhoneRepair my S7 Edge won't charge, i replaced the battery but still won't charge, i used different cords but still won't charge even the wireless charger, do you think the charging system is the issue? same as the video above?
Reflow u9005 ic
Outstanding video!
Thank you for watching this tutorial! Best regards
ótimo vídeo,parabéns!!!
qual o nome das colas que você utilizou?
Paulo Teodoro gracias por sus apreciaciones! Recomendó b7000 or t7000! Un saludo cordial
Hi... does the fast charging work again?
Hello, Yonas! Yes, it should work normally! Best regards and thank you for asking!
Is there one with a usbc port out there?
They didn’t mention this in the video, but I want you guys to be careful when taking off the screen and going through the adhesive, don’t poke too far in near the lock button because that’s where the cable for the LCD is and it’s very sensitive, i accidentally ripped mine because I didn’t pay attention to how close the cable was to the edge. Not blaming the video maker, it was my mistake, just don’t want anybody else to make it and have to spend $150 for a new LCD
Mincraft, thank you for your advice& for your comment! Best regards
Really good job
Hello, Achraf Zaidi! Thank you for your comment! Best regards
what is the name of the Glue you are using?
Hello, Manuel! It B7000 the glue.Best regards
This video is a Full Disassembly; there are several other videos that do not remove as many components and take less time.
Thanks for your comments.
excellent video
That is impressive, but so much work. I think I'll just live with mine and use some tape to hold the cable in the port just right until I can buy a S9.
:) Thank you. Is true, so much work...:) Have a nice day
www.movilone.es
hahaha true
that's very hard to fix
Skip the 9 go to 10.
You've got to hand it to Samsung they make it so easy to replace charging port😂
Sir I have Sam s7 edge for which normal charging is working, but fast charging and USB connection is not working, I've also checked with another device for which fast charging is working with same cables
Hello, Prakash! According with the information that you provide, i Thing you have a problem with the charging conector and the tracia that aré responsible for the computer connection aré damaged! Thank you for asking! Have a nice day
Thank you bro very nice
Thank you Malik for watching this tutorial! Best regards
Is is the phone still waterproof?
Hello, Silver! No, it s not gonna be more water resistant! Best regards and thank you for asking!
Charge port had attach touch buttons left write as well????
Hello, Farzana! In this case, charging connector is a flex that has other accessories too, buttons, microphone ...Any informacion you might need, i m at your disposal!Best regards
www.movilone.es
Can you please make a video to how solve the pink line problem in s7 edge
Hello, Prakash!I will take your request into account. There are several users that are asking me, the same thing. Thank you for watching! Best regards
Type of glue?
T7000! Thank you for asking
Great work !
Thank you! Have a nice day!
All them ribbons 😮 I'd for sure bend a pin trying to snap it back on
Adhesive?
awesome...nice Job.
Thank you, Ismael Gonzalez for watching our tutorial! Best regards
Damn, the stuff that happens around 11:20 is pretty crucial. Just broke my S7 screen into 100 pieces, phone goes in the trash.
Wish I knew where in your channel the video without removing screen was before following this guide. Can't find it.
Oh well, have to use a new phone instead!
Hello, Karl! I really feel bad for you; this is the link from the another method that I used without remove the screen ruclips.net/video/t14Ae_xysmY/видео.html
Also, I have to tell you that you need some experience, too...it s not easy to repair it and some good tools! Best regards
Bro without removing screen can we change it
Hello, Farhaan! yes, you can do it without removing the screen, informó act I ve got another repair in my youtube channel were I m doing this repair in that way. Thank you for asking! Best regards
MovilOne thanks bro
The screen removal almost seem impossible,but I will be careful with my track pad next time, because I just cut mine.
You missed some parts with glue.
My S7 edge won't charge with any cable or adapter. Is the USB port the problem?
Sandu Zmeu , Hello! Probably you ve got an problem with the charging connector or with the battery! Let me know if you need more info
It charges without problems with a Wireless Charger. I only have a slow, 5W Wireless Charger which charges my phone in about 5 hours... But I can still connect it to PC and transfer files. I only repaired an iPhone 6 and a LG G4 before, and to get inside I just needed a screwdriver... But here, It's a little bit more complicated 😂.
Great bro
Thanks! Greetings from Spain!
great work
Thanks.
What is the price of this charging port
Hello, Arshad!i ll just attach you the link of this repair: www.movilone.es/reparar-conector-de-carga-samsung-galaxy-s7-edge If you have any question, please let me know! Have a nice day!
www.movilone.es
How do I fix the usp port on it my son's bottle spilt on it and now it won't charge
Bethany, it s better to proced with a ultrasonic cleanning, before replacing the usb connector. Wish you good luck! Best regards
MovilOne Phone Repair ultrasonic cleaning USB port
Sir mai v apna s7 edge ka charging port change krwana chah rha hu bt koi nhi kr pa rha h
Hello, Krishna! We can do it, don t doubt it, but we are from Spain, so if you contact us from outside the national territory, please use the form contact on our web site www.movilone.es Thank you and have a nice day!
Why fast charge in video not work ??
Good job
Thank you, Henry for your comment! Best regards
Super
Thank you, Arjun for your comment! Best regards
i have replaced so many screens and ports over the years. I told my friend I would fix her port and this scared the sh*t out of me. Damn it this is going to suck balls.
:) You are right! Is complicated but not imposible, like you see! Have a nice day
www.movilone.es
This is righteous, dude. You're a pro
Kyle Seeley,thank you for your comment and for watching this tutorial! Best regards
@@MovilonePhoneRepair I looked it up cause i work at a repair shop and im gonna try to start doing the charge ports. Super cool idea to work the bottom half first, thanks for the good advice
Klye, wish you good luck and if you need more information, i ll be glad to help you!! :)
Amazing...
Thank you, Emmanuel! Have a nice day.
www.movilone.es
ta vidéo est tro bien sil-teplai refais une votre vidéo sil-teplai
Thank you, Ramatou! I hope it has been helpful Best regards
www.movilone.es
Nice
Thank you for watching! Best regards
Why is it so difficult to do?
Why do you need nifty fingers?
I can't do this otherwise I'll break something
Really, this repair is quiete difficult. You need good tools and some experience! Best regards and thanks for sharing with us your opinion!
Les ingénieurs Samsung ne sont pas compatissant, ils auraient pu nous faciliter ! Ca aurait été plus commode pour nous "les Clients". Autant changer de téléphone
Ie Tass, you are right! they make it harder every day :( Thanks for watching!
I need to do this to my s7
Hello, James! It s similiar,the same steps to follow, with care....Best regards!
www.movilone.es
Братан нагрей Арарат нормально не мучяйся у меня чуть енфарт не случился
:) Thank you for watching!
It pays to replace a Galaxy 7 socket today
They really don't want you to take apart these phones do they. Honestly,my patience would probably run out and I would smash the phone into a million pieces.
Hello, Gene! One of the characteristics that you have to have to be a good technician is to have patience :) Thank you for watching this! Best regards
No wonder these cell phone repair places charge so much money. Look at all the components you have to remove and put back.
Thanks, Tinydancer for sharing your opinion with us. Best regards
holy shit thatts too much. my phone's charging port does not work so i was thinking of replacing it but after seeing this video , nooo man. no. im good with wireless charging
:) Yunus!! You've made me laugh :) Is better for you to take it to specialized technical service, the wireless charge ... what will cause that in time it damages the battery, the duration of the load is not the same ... let's say it is an option at the moment ... Best regards!
Lol I use the Samsung Wireless port but I am still deciding on whether to risk to fix the port or not because it takes like 3 hours for my phone to charge with the wireless port.
cringe. u don't need to use force so much if you use the heatgun more. u likely damage the parts with the way your removing them
Tried it, turned the phone back on and the LCD's ruined. $350 for a new one, the same price as a new phone lol
Chris, i m so sorry to hear that! If it seems to you, so complicated you should let it on hands of some technical service from your area.... Wish you good luck!
@@MovilonePhoneRepair all good, it happens. Was worth a try, it needed to be fixed one way or the other and the repair shop said it would almost definitely break the screen anyway
Chris, there is a tool with which we open these devices without breaking the screen ... but well, the fact is done ... so, the next :) more carefully!Best regards
@@MovilonePhoneRepair the same issue lol, wish u would have mentioned that do not go from the button of the screen with playing cards. it went in between the digitizer and that screen paper. what is that tool u mentioned?
Agar aap kr denge change to visit kr sakta hu aapse apna contact no. De
Krishna, use the form contact on our web site www.movilone.es
Best regards
GOOD
Hello, Fixit Proz! Thank you for your comment! Nice to hear that! Best regards
I do not have the patience or will ti do all that. I will just buy a new phone. Im 65 now and i'm lazy . Ha ha😊
jejje, love life! Thanks for watching anyway! Best regards
Please remove the baterry flex firsly you can't work like that please do a better job you can't desconnect de lcd flex wen the battery is still connected
Kids... Don't try this at home. 😵😵💫😱
Thanks for watching! Best regards
Tools :1deck of cards lol.
Hi
Hii
Hello, Vinod! Welcome :) How can I help you?
👍👍
Thanks for watching! Best regards