Thanks for posting a brief and to the point video on how to change the battery. No long introductions, no life story, just simple and direct instructions.
Fantastic - perfect voice for this, perfect description with pure professionalism . I changed my screen and also replaced the fading battery with a higher capacity 4500mAh thanks to you. Keep up the good work. - GC from Adelaide, Australia.
Bought a battery replacement kit from Amazon and it linked me to this video for instructions! 😅 I should’ve known to look for a jerryrig video already!
Jerry, your RUclips presentation gets referenced by sellers of iPhone batteries. I appreciate the iPhone 6 Plus kit I bought at Amazon. Took me 4 hours to swap out the defective (swollen) lithium battery. The included tools were a godsend. Sadly there were NO INSTRUCTIONS. I could not figure out where to put the blue phone-sized plastic sheet, so I left it out. Is it some kind of protective insert? Any ideas? Reassembly was a challenge. Teeny screws were hard to handle and find when they disappeared. I had to play and pause your video to recall the sequence. Your video gave me the courage to finally tackle a DIY challenge, a year after Apple offered to change my expanding battery for over $100. ~Allan (77 years old in Chelsea, MA)
The tabs on the battery are there for a reason, you should never pry the battery out of an iPhone 6 Plus, as the battery will be damaged or bent. Just lift up the two black tabs on the battery, and pull them slowly outwards and they will stretch as they release from under the bottom of the battery, allowing the battery to be just lifted out with no effort. These tabs need to be renewed when replacing the battery. Do not use double sided tape, as when it comes to the next battery change, prying out the battery will be the only option, and may cause damage to the phone or components. Do the job properly, and make sure all the screws are located in the same hole they were removed from. Some are slightly longer than others, and if put into the wrong location, may cause damage to the logic board.
you just peel that black tab back (it's attached to the glue), and pull it straight away from the phone, like those 3M command strips i really wish i figured out this is what he meant before i started prying and heating and prying
I also used the pull tabs which made it easier to remove the old OEM battery. New kit also came with this glue tape. I was able to replace my mom's battery without any issues! She doesn't want a new phone and the only issue was the battery draining quickly. Now it is good as new for her. Thank you!
Your video was really helpful! I was able to remove the old battery without removing the screen and screen cables. Thanks alot for the help though! Highly recommended for all new installers!
I just followed the steps and I successfully replaced the battery! The reconnection of the screen cables were somewhat difficult. Had to try three times. But it was a happy end.
Just replaced my iPhone 6+ battery using this video. The pull-out tabs snapped on my battery then I got a nasty spark when I accidentally pierced it using a pry tool. Scary, but no harm done. Thanks Jerry, couldn't have done it without this.
Important to make sure the battery connector aligns with the socket before applying adhesive. Some batteries require that the ribbon connector has to be bent to draw the plug a little bit closer to the battery; this is true of the "Amazon's choice" Loctus battery. Suggest a "dry" run where the new battery is simply placed in the empty case and connected, ensuring fit and position. Thn disconnect and remove new battery; apply adhesive to back side of battery, then plug the connector into the socket once again before finally dropping battery with adhesive into the case.. guaranteed fit and placement.
Thanks, second time I've replaced an iPhone battery with the help of your videos! Always great - nice and fast too! The first hit video was 45m long. :)
thanks to this i did my first repair, my vict... volunteer was my sister and it worked perfectly, I used school glue since it said acid free and so far its been ok. Thank you a bunch.
Like how you casually but fast skipped past the acid part this video was short and very helpful that part scared me a little bit other than that thumbs up ! 👍
What you're calling glue are tape strips and can be pulled out from the top from what I've seen in other video's pertaining to iPhone battery removal. Nice video overall.
JerryRigEverything if you're familiar with command strips, the adhesive for the battery functions exactly like that. No heat required. You can just pull the adhesive out from under the battery and it requires almost no force and no stress on the battery.
Perfect, many thanks. As advertised, I would suggest to anyone doing this to make sure they note which screws come from where (one or two are longer than the others) and you do it on a tray or white cloth...anything to arrest those bloody screws in the event of a "ping...oh crap" moment. Much appreciated, thanks again😁
I want to thank you for all your help I did everything you said. it was one of the wires the one that Connects to the home button and on the top.. Now my iPhone 6 plus is working again..
There are two screws that are different lengths from the rest and from each other. It would help to note which goes where. The long one is unambiguous, the medium one is the challenge. It goes on the upper left of the retainer plate shown in the video.
Thanks for posting this video. I’m going to be changing my battery within the next few days, and I’m so nervous! Lol. Definitely going to save this video to use when I’m changing the battery. Thank you!
Great Video! Take him serious when he mentioned to be careful not to cut the battery. I accidentally bent the battery as I was trying to get my plastic tool under it. Battery cover cracked, small electrical arcs from the battery to the metal body, followed by a tiny fire and smoke. Other than my accident it worked well. Also be sure you line up the battery correct when you put the new one in. I set the battery in a bit low so the ribbon connector didn't fully reach, had to move it up which was hard to do with the new glue. Learn from my mistakes.
Thank you for this video.. I manage to do it super well with it.. You were right that the battery removal can get savage... It was for me.. It had even more glue than the one on this video.
Thanks so much for your video, it really helped me changed my son’s battery, but instead of having 4 plugs for the screen, his iPhone 6S Plus only had 3 for some reason. But your video really helped, especially when it came to getting that Battery out using a heat gun and plastic tool. 👍👍👍
Thank you for the video! I just got my battery replaced and was wondering how it was done. I would have been so scared something might go wrong if I tried to do it myself! My phone's battery was lasting an hour after a full charge so I'm excited to finally have a battery that will last through the day!
Important things not mentioned: The phone has a sticky gasket around the perimeter that must be overcome. A replacement gasket is supplied in the kit. The old gasket must be removed entirely. Some screws are different sizes and go into specific places.
Before I declare a software problem my iPhone battery life shows 71 percent in my settings so I am changing my battery this morning because of unusual power drain, which my battery is junk so this should fix it. Thanks for the vid, Short, sweet and to the point, 2 thumbs up!!
I have seen several videos on how to remove the batteries on iPhones. I am still amazed that NOT ONE SINGLE PERSON - including the person in this video - understood how to remove the battery from the case. I know the following works because I removed the battery from an iPhone 6 using this method. Those two little tabs - clearly show in the video - are EXACTLY the same as the tabs on Command Strips. . . . . you grab the tab and SLOWLY pull on it. You might have to use tweezers to get the first grip. Lift it up and grab with your fingers. Pull and pull and pull SLOWLY . . . When one strip is done . . . then do the other one. . . . Just like a Command Strip . . . viola! The battery comes out cleanly and simply. NO battery damage from prying . . . NO case damage from prying . . .
Thanks, very helpful and concise! I did it without taking the screen off but prying the old battery out took a lot of time and effort! Will definitely try heating it the next time!
I also did it without taking the screen off. If you do not heat the back you could damage the rather thin metal housing. I have the luxury of being someone who 3D Prints so I have a heat gun for them my 3D Printer nozzle or heatbreak needs attention. Not everyone have a heat gun but a hair dryer will also work, just might take longer to heat it. BUT you should heat the back to make it a whole lot easier to remove. But do not overheat the back.
No kidding!!! This guy needs to start over unhook the battery connection first then the screen, but you can change the battery without removing the screen
Thanks for posting a brief and to the point video on how to change the battery. No long introductions, no life story, just simple and direct instructions.
Totally agree
Thank you for not posting a 15 minute video about this. This was the perfect pace for this type of video.
Heck ya! Thanks for watching! Glad you enjoyed it.
Do you loose any info or data when replacing battery?
Mitchell DeVaughn no, nothing at all.
@@ashishx__5616 100 % after battery change
Fantastic - perfect voice for this, perfect description with pure professionalism . I changed my screen and also replaced the fading battery with a higher capacity 4500mAh thanks to you. Keep up the good work. - GC from Adelaide, Australia.
Wow 4500 mah
Bought a battery replacement kit from Amazon and it linked me to this video for instructions! 😅 I should’ve known to look for a jerryrig video already!
Jerry, your RUclips presentation gets referenced by sellers of iPhone batteries. I appreciate the iPhone 6 Plus kit I bought at Amazon. Took me 4 hours to swap out the defective (swollen) lithium battery.
The included tools were a godsend. Sadly there were NO INSTRUCTIONS. I could not figure out where to put the blue phone-sized plastic sheet, so I left it out. Is it some kind of protective insert? Any ideas?
Reassembly was a challenge. Teeny screws were hard to handle and find when they disappeared.
I had to play and pause your video to recall the sequence. Your video gave me the courage to finally tackle a DIY challenge, a year after Apple offered to change my expanding battery for over $100.
~Allan (77 years old in Chelsea, MA)
The tabs on the battery are there for a reason, you should never pry the battery out of an iPhone 6 Plus, as the battery will be damaged or bent. Just lift up the two black tabs on the battery, and pull them slowly outwards and they will stretch as they release from under the bottom of the battery, allowing the battery to be just lifted out with no effort.
These tabs need to be renewed when replacing the battery. Do not use double sided tape, as when it comes to the next battery change, prying out the battery will be the only option, and may cause damage to the phone or components.
Do the job properly, and make sure all the screws are located in the same hole they were removed from. Some are slightly longer than others, and if put into the wrong location, may cause damage to the logic board.
Bout to give this ago...🙏🏾For this‼️
you can pull out the battery by using the adhesive pull tabs at the bottom of the battery instead of heating up the phone and prying the battery out.
This was so much more simple lol thanks
Alex Wolfe wish I read the comments before removing battery.
Alex Wolfe what do you mean?
you just peel that black tab back (it's attached to the glue), and pull it straight away from the phone, like those 3M command strips
i really wish i figured out this is what he meant before i started prying and heating and prying
YEAHHHH!!! JAJA :p
2 hours of suffering, nervous, agonia, thoughts that I'll never switch on my telephone again...
And it's done! 😉 thank you!
Thanks. Straightforward and simple. No life story and no music!! Worked a treat.
Totally agree
Thanks again - my second battery replacement on an iPhone using your replacement kit and video. Great work!
Quick, clean and precise videos! You're awesome! I don't even have a problem with my 6 plus... Just wanted to watch your vid.
Thanks Jerry...I was able to replace the battery for my 6S with this helpful video... thanks again
I also used the pull tabs which made it easier to remove the old OEM battery. New kit also came with this glue tape. I was able to replace my mom's battery without any issues! She doesn't want a new phone and the only issue was the battery draining quickly. Now it is good as new for her. Thank you!
Thank You
the best tutorial so far, direct and effective
Thanks for the instructions. I was able to do it without disconnecting the screen.
Your video was really helpful! I was able to remove the old battery without removing the screen and screen cables. Thanks alot for the help though! Highly recommended for all new installers!
I just followed the steps and I successfully replaced the battery! The reconnection of the screen cables were somewhat difficult. Had to try three times. But it was a happy end.
Thanks... you saved me around £30.00! Managed to replace my battery with this video... but it did take me more like 30 minutes!
Excellent thanks it’s very good information thanks 🙏🌹👋🌹🙏
Just replaced my iPhone 6+ battery using this video. The pull-out tabs snapped on my battery then I got a nasty spark when I accidentally pierced it using a pry tool. Scary, but no harm done. Thanks Jerry, couldn't have done it without this.
Important to make sure the battery connector aligns with the socket before applying adhesive. Some batteries require that the ribbon connector has to be bent to draw the plug a little bit closer to the battery; this is true of the "Amazon's choice" Loctus battery. Suggest a "dry" run where the new battery is simply placed in the empty case and connected, ensuring fit and position. Thn disconnect and remove new battery; apply adhesive to back side of battery, then plug the connector into the socket once again before finally dropping battery with adhesive into the case.. guaranteed fit and placement.
Thanks, second time I've replaced an iPhone battery with the help of your videos! Always great - nice and fast too! The first hit video was 45m long. :)
thanks to this i did my first repair, my vict... volunteer was my sister and it worked perfectly, I used school glue since it said acid free and so far its been ok. Thank you a bunch.
Nice video bro , you are calm and very smooth with it
Thank you for the video. I was able to switch out my battery and saved a lot of money in the process. liked and subscribed.
Great directions! Concise and to the point - worked perfectly!
Totally agree
I like your voice. Cool and calm instructions.
Like how you casually but fast skipped past the acid part this video was short and very helpful that part scared me a little bit other than that thumbs up ! 👍
Perfect. Just what I needed to help me change my battery. Thanks so much for posting this no nonsense video.
I followed the instructions and replaced the battery successfully. Thanks!
Very easy to understand your videos thanks
Motabbir Hussain No problem! Thanks for watching my video!
Thank you so much for posting a "hair dryer and pry" version! My tapes all broke and had to do it this way. Very helpful!
No questions 🔥🔥 worked well
Worked perfectly, very easy to follow, especially with the added tips about pulling the tape vs heating the adhesive.
What you're calling glue are tape strips and can be pulled out from the top from what I've seen in other video's pertaining to iPhone battery removal. Nice video overall.
Ben7seven7 Ya, I realized as I was editing it that I kept saying glue. lol, im an idiot. But either way. The things are super strong.
JerryRigEverything if you're familiar with command strips, the adhesive for the battery functions exactly like that. No heat required. You can just pull the adhesive out from under the battery and it requires almost no force and no stress on the battery.
Perfect, many thanks. As advertised, I would suggest to anyone doing this to make sure they note which screws come from where (one or two are longer than the others) and you do it on a tray or white cloth...anything to arrest those bloody screws in the event of a "ping...oh crap" moment. Much appreciated, thanks again😁
You make it look easy. Great Job.
It educate myself to know & learn how its done... thanks to you, sir.
I want to thank you for all your help I did everything you said. it was one of the wires the one that Connects to the home button and on the top.. Now my iPhone 6 plus is working again..
Thank you so much. You did a great job with assisting people for this.... Regards pal...
Worked perfectly, followed the tip about the tape strip pulls instead of heating
Thank you so much for this video! That was super helpful.
What a superb instructional video,thanks loads for doing this!
Thank you for this video. Got my replacement battery today and I will be able to do it with your help 🙏🏼😊
Thank you so much for this!!! You are a life saver!! 😆
Thank you, very short and precise video. Outstanding!
Followed the video and it worked great. A lot easier then I thought it would be. I didn't have a heat gun, so I used a candle.
I appreciate your great 'very explainable' instructions!!! :)
Great video. Subscribed
There are two screws that are different lengths from the rest and from each other. It would help to note which goes where. The long one is unambiguous, the medium one is the challenge. It goes on the upper left of the retainer plate shown in the video.
Great tutorial, very helpful. Thanks a million bud!
Thanks Man! worked perfect, wifey did assist which was a great help.
Thank you so much bro it helped me a lot
normally i see a 30min vid for something that takes 4mins good job man
Thank you, I was able to change my iPhone 6+ battery because of you!!!!!! I do appreciate it!!!
Thanks for posting this video. I’m going to be changing my battery within the next few days, and I’m so nervous! Lol. Definitely going to save this video to use when I’m changing the battery. Thank you!
Great Video! Take him serious when he mentioned to be careful not to cut the battery. I accidentally bent the battery as I was trying to get my plastic tool under it. Battery cover cracked, small electrical arcs from the battery to the metal body, followed by a tiny fire and smoke. Other than my accident it worked well. Also be sure you line up the battery correct when you put the new one in. I set the battery in a bit low so the ribbon connector didn't fully reach, had to move it up which was hard to do with the new glue. Learn from my mistakes.
U
maybe if we used up all the power the battery will become safer?anyone tried these?
😂😂😂
I did the same thing. Scared the $hit out of me and now my house stinks!!!!
I'm assuming my phone is toast like literally!
Thank you for this video.. I manage to do it super well with it.. You were right that the battery removal can get savage... It was for me.. It had even more glue than the one on this video.
Who’s here because Apple admitted that they slow down older iPhones?
Manuel lol yup
Me
We all are. I just let someone replace it though. So you guys experience slowdown too?
Changed my battery for 6s it still drain like water I think it software problem 11.2.1 suckssssssssss don't upgrade
Yanno Love i didn't. Did performance change?
All fixed, Thanx for tha help BRUDDA!!
Thanks so much for your video, it really helped me changed my son’s battery, but instead of having 4 plugs for the screen, his iPhone 6S Plus only had 3 for some reason. But your video really helped, especially when it came to getting that Battery out using a heat gun and plastic tool. 👍👍👍
Without you, I wouldn't be able to do this....I did it in about an hour though, LOL! Thank you!
Thank you for the video! I just got my battery replaced and was wondering how it was done. I would have been so scared something might go wrong if I tried to do it myself! My phone's battery was lasting an hour after a full charge so I'm excited to finally have a battery that will last through the day!
thanks brother. It really helped
Important things not mentioned:
The phone has a sticky gasket around the perimeter that must be overcome.
A replacement gasket is supplied in the kit.
The old gasket must be removed entirely.
Some screws are different sizes and go into specific places.
Thanks, very useful video
Thanks, this video helped me a lot in changing my iphone
perfect demo. thanks
Perfection! I did just as you said and it worked like a charm. Thank you.
Great tutorial. Did mine in 25 mins. And my phone is like new again! Thanks!
Excellent video so simple thanks
Before I declare a software problem my iPhone battery life shows 71 percent in my settings so I am changing my battery this morning because of unusual power drain, which my battery is junk so this should fix it. Thanks for the vid, Short, sweet and to the point, 2 thumbs up!!
Thank you Jerry that’s very helpful. Godspeed.
This was awesome. Just replaced battery and charging port on phone, Feeling Powerful!
Thank you so much for your helpful
explanation. I did successfully ! Greetings!!
I just replaced my old 6 plus and this is my first time ever I did in 15 min. Now my old 6 plus is like a champion. Thanks
I have seen several videos on how to remove the batteries on iPhones. I am still amazed that NOT ONE SINGLE PERSON - including the person in this video - understood how to remove the battery from the case. I know the following works because I removed the battery from an iPhone 6 using this method.
Those two little tabs - clearly show in the video - are EXACTLY the same as the tabs on Command Strips. . . . . you grab the tab and SLOWLY pull on it. You might have to use tweezers to get the first grip. Lift it up and grab with your fingers. Pull and pull and pull SLOWLY . . . When one strip is done . . . then do the other one. . . . Just like a Command Strip . . . viola! The battery comes out cleanly and simply. NO battery damage from prying . . . NO case damage from prying . . .
Thanyou very much for clear instructions.
Th So Much for Sharing i was able to Replace my battery myself n Save a Lot of money !!! Bless you! 🙃😇
Great video it did the trick.....thanks so much!
😀😀😀😀
Worked a treat. Thanks
Hey, what do you recommend after replacing the battery; charge it to 100 or let it drain to 0?
Thank you for your teaching. I've done with my battery changes!
Awesome video, thanks 4 sharing
Thanks, very helpful and concise! I did it without taking the screen off but prying the old battery out took a lot of time and effort! Will definitely try heating it the next time!
I had the same experience with you.
I also did it without taking the screen off. If you do not heat the back you could damage the rather thin metal housing. I have the luxury of being someone who 3D Prints so I have a heat gun for them my 3D Printer nozzle or heatbreak needs attention. Not everyone have a heat gun but a hair dryer will also work, just might take longer to heat it. BUT you should heat the back to make it a whole lot easier to remove. But do not overheat the back.
very comprehensive video!!! thankssssssssssssss
This was a great video. Saved my life :)
Great video
Great demonstration made to look easy.
Great explanation awesome awesome job
thank you very much
this help me to repair my iPhone in this lockdown 😍😍😍
Job done. It worked. Cheers
really nice video ! Thanks a lot
Thank you man for the information
thanks for posting sir
Excellent instructions.
Thanks! Just replaced my daughters phone battery all by my self! So stoked!
Please for the love of god disconnect the battery first please before removing the display flexes.
Yep...found out the hard way. God damn it.
Dream Arez let them not do that . I can fix more burned ic components
No kidding!!! This guy needs to start over unhook the battery connection first then the screen, but you can change the battery without removing the screen
thank you sm i want to use my iphone 6 plus again as my back up phone but only for the camera lol but this really helps !