well it's a lathe ruclips.net/user/postUgkxN9zrzkkhnjUF5PQbuA_B1gYdsfCu9k6z but it wasn't what i would have anticipated. Headstock, tailstock, carriage apron are manufactured from aluminum now not cast iron. The spindle diameter for the bearings is too small allowing for a few play in the spindle so I am using some blue Loctite to take out the play.
You mentioned 'totally dry, no oil or grease' several times. That's very unusual. I think you got a return. It didn't need to be broken, someone just didn't like it. Clue: the lathe manufacturer doesn't make chucks, they buy them built and already soaked in grease. That one was dry and rusty. It didn't leave either the chuck or lathe manufacturer that way.
Apparently selling returns is quite common and it should be the first thing to inspect for. I saw another youtuber's video and he also got a returned lathe sold as new, he asked for a partial refund since he decided to keep it anyway.
Just a tip; you tightened the belts up very tight... this is bad. Aluminium pulleys have a large thermal expansion in use, and the toothed belts have tensile glass fibre reinforcement that does not stretch. As a general rule, you should always run toothed belts loose enough so the belts can slide sideways on the pulleys, this allows some room for pulley expansion. If the belts are tight the pulley expansion quickly destroys the glass fibres and the belts will break.
good luck. i have one of these. the roller bearings were not mounted correctly or the seats were not square which you could see in the uneven wear pattern. i re-seated them and adjusted the preload and the spindle handles parting much better. The other key mods i did were: remove the compound and make a solid tool post block, I used shims vs the set screws on the saddle and I had to machine a new gib because the one it shipped with could not be adjusted. Put your indicator on your tool and push down on it to see how much it can move down towards the ways. The tail stock was total garbage and needed lots of rework. The gears can't do many thread pitches because the banjo is not the right size. The charts for the gears in the manual were not for a 56 tooth spindle gear and did not work. I ended up just removing the gears and installing an electronic leadscrew. the machine cuts a taper and the headstock is not square to the ways, cut a long bar stout and measure the end diameters to see if yours is cutting a taper. My chucks are decent but it is strange they sent a 3 and 4 jaw self centering vs an independent 4 jaw. anyway... good luck.
Thank for making this video! Nice video, Mr Maxim! I bought 1 of this lathe model VM210V also. But seems like the extra gear provided by the manufacturer to perform(cut) the metric screw thread operation on the lathe were not accurate on the pitch(I mean the gear ratio). Possible for you to share your English technical manual?(probably a link to download). Mine technical manual was given in Mandarin version, so have a hard time reading it. Thanks & appreciate in advance! Rdgs Stan😊
Q: Greetings Master, what is the maximum tool size that the stock toolpost accepts? A: At 3:33 you reply to this, sorry: 10mm is the default toolpost Q: What did you had to do be able to use the 12mm tools centered on the axis?
My dear friend, you can use 12mm tools with a 250-001 tool post (see AliExpress) - but I recommend using 20mm tools as per ruclips.net/video/2Hvbsx-P7fA/видео.html
"I got it down to 2-hundrets..." This is the moment , where you face your chuck and indicate your spanning point. - because it makes a huge difference.
Just subscribed and I've been watching your videos most of the morning. Nice family life you've got going on there. I'm getting ready to buy my first metal lathe and I've narrowed down to the one you have and a couple others including the Grizzly G0765. Are you happy overall with your purchase, and if you had it to do over would you buy the same model? I really like what you did with all of the steppers and bearings for improved performance, which is why I'm considering going with the same so I can just follow in your footsteps.
Dave, I'm not really using my lathe for any practical purpose, just playing with some parts now and then - so no expert on the subject. This exact model has gotten more expensive since I bought it (especially the shipping), today I'd probably go for www.aliexpress.com/item/678185093.html instead - it appears incredibly similar but I can't guarantee that all the 3D models will fit it perfectly since I didn't try that. Best wishes!
@@MaximKachurovskiy Thanks Maxim, I just checked it out and it seems like the price is fine, but they want 750 to deliver to the U.S. My gut keeps pushing me to buy the Grizzly because of their customer service. Then again, I may buy one and get bored with it and then watch it collect dust. Anyway, thanks for your help.
Видимо у них разные критерии ОТК для СНГ и Запада. В том который приехал нам половина деталей вырублена топором. Включая контактирующие со станиной "плоскости" (именно в кавычках) каретки суппорта...
Thank you, Great video. I just spent about a week looking at these little lathes and think this is the best one on Ali-express. After the last 3 years would you still recommend to buy this machine? I am a fitter/machinist so I'm capable of fine tuning and resolving issues. I just need something small in my shed for motorcycle and car parts and don't want to spend more than $1500AUD and this one is currently $1300.
This lathe is no longer available but similar ones are. They vary in quality. Check out Numobams brand, I believe they sell decent lathes unlike some other companies.
@@peatergriffin no - but don't pay for those cheap gearboxes, they are no use, just get an after-market electronic leadscrew. There are many including ones I offer on kachurovskiy.com/
@@MaximKachurovskiy Thank you very much. Yes I saw alot of bad reviews on that version. I think I found this same lathe from a seller called CNC QIYI TOOL Store. I appreciate the video and response.
You should invest in an ultrasonic cleaner. It would make the job of cleaning the grit and rust 1000x faster and cleaner. They are a lot cheaper than they used to be. I picked one up for about $100 on eBay and it has helped me our a lot.
Bob, I saw they need special filling too? Not sure I understand how they work exactly. Operations like these are rare at my shop and space is at a premium so I decided to skip on them for now.
@@MaximKachurovskiy Nope! No special liquids needed, just degreaser mixed with water. It depends on what you're cleaning. They come in all sizes, and are great for cleaning almost anything.
@@MaximKachurovskiy I love my ultrasonic cleaner, and they can be used for all sorts of things. The Thought Emporium made a video about artificially aging cheap alcohol by adding wood chips and running it in an ultrasonic bath.
The 250-000 tool post and all the attachments for it are from AliExpress, too. It fits fine without any machining but the limit pin that you see sticking out from the plate on 8:28 makes it inconvenient to rotate the tool post which is not a super big deal because tool post is usually kept in place and not rotated often. What is more of a problem is that 250-000 tool post is small and flimsy i.e. it will vibrate under load and vibration breaks carbide cutters. There are some workarounds for this problem but maybe getting a slightly bigger/different tool post is a better idea 🤷
@@MaximKachurovskiy Maybe the 250-100 but it seems that this tool post needs some work to modify it. Also some have modified the compound by adding more screws to tighten it better: fr.aliexpress.com/item/4001204070693.html?spm=a2g0s.8937460.0.0.7d802e0eiUtDv0 I wonder if this one could be any better than the 250-00: fr.aliexpress.com/item/4000857204659.html?spm=a2g0w.12010612.8148356.21.447d4d6cLz8iKU
Nice overview! If I noticed rightly, you were using Liqui Moly multi-purpose grease for all gears. What kind of oil you are using to lube all lube points and slide ways?
Thank you. I've switched to Nigrin www.amazon.de/Nigrin-74145-Mehrzweckfett-Tube-250/dp/B001BAU3VY for lithium grease because it has very little smell compared to Liqui Moly - and also easier to apply from the tube. For oiling, I'm using the sliding oil I bought for the mill: www.amazon.de/gp/product/B01MZFZVPO - it almost entirely removes the "sticking" effect when a part starting moving after standing still for a while. It also has very little smell. Seems good for drilling and thread cutting too.
Hi, schöne kleine Drehbank. Ich suche auch schon einige Zeit nach diesem speziellen Typ. Können Sie mir sagen wo ich diese Drehbank kaufen kann? Vielen Dank. Gruß
@@MaximKachurovskiy Danke für die schnelle Rückmeldung. Das habe ich mir schon gedacht. Die Maschinen von Vevor habe ich auch schon ins Auge gefasst. Wieviel KW hat Ihre Maschine? 750 Watt?
@@reneh4602 Die Wattangaben auf AliExpress werden normalerweise überbewertet. Ich weiß nicht genau, wie viel Watt mein Motor hat. 750W sollten ausreichen.
how do you like this lathe, one year later? I'm considering buying one to work mainly with plastics, but i do need to have good tolerances and would probably set it up with a DRO
It's a good lathe but you will have a lot of trouble fitting a DRO onto it, there's just isn't enough space, consider buying one with a DRO pre-installed.
Hi, yes, this is a good lathe. It's not perfect, with more money you can buy a much heavier lathe that will be much better but that's a different story.
To adjust the gears, put a piece of paper between them, tighten the gear nut, then remove the paper. I used Nigrin lithium grease because it smells less than other greases. Cheers!
У меня пoхожий станок, только с коробкой передачь на 3 скорости и переменой направления. К сожалению на этом всё. Куда нос не сунь то дырки высверлены не туда то зазоры как крысинные норы. Месяц только пытался понят как и что. Кстати, спасибо за модифицации на thingyverse.
Dominic, I paid 857€ total of which 264€ was delivery. Currently delivery is very expensive, this happened before, just check back in a few weeks. Cheers!
@@MaximKachurovskiy Привет. Сам буквально на кнопке заказа сижу. Думаю серый взять через ИБей, или может тоже такой взять. Как тебе станок твои? Может что посоветуешь. Я тоже в Германии живут. Ты говоришь 850€. А там сейчас стоит где то 630€ станок и пересылка 790€. Это как?
@@werschkowdennis6533 опять подорожало видимо. Уже такое было несколько месяцев назад, в комментариях обсуждали. Подожди месяц, должно вернуться в норму. Дополнительные деньги таможня с меня не спросила. Серый говорят существенно хуже.
Gear calculator for this lathe: kachurovskiy.com/gears/ 90€ Electronic Lead Screw for this lathe: ruclips.net/video/9uTdDk2EqG4/видео.html / github.com/kachurovskiy/nanoels
Привет. У меня новый 8x16 MX210V ,когда поварачиваешь ручку спид контроля, то станок начинает работать со 180 оборотов , если повернуть ручку на уменьшение то просто останавливаеться. ремен. стоит на малой передаче от 0 до 1250об. но на деле получаеться только от 180...?? случайно не знаешь в чём дело?? Спасибо.
Привет, я сам мало понимаю в этом деле как видишь но можно погадать. Попробуй гитару временно разомкнуть со шпинделем - может она стопорит на малых оборотах из-за трения шестерёнок.
Sehr angenehmes Video, dadurch, dass Sie ruhig sprechen und keine wilde Hintergrundmusik verwenden. Danke für Ihre Arbeit, auch für Electronic Lead Screw @ Github. Das und andere Videos von Ihnen werde ich mir demnächst zu Gemüte führen :-). Very enjoyable video, in that you speak calmly and don't use wild background music. Thank you for your work, also for Electronic Lead Screw @ Github. I will have a look at that and other videos from you soon :-).
Averell, no, it just showed up at the door. This particular seller ships by ship from China to Poland and handles all the customs. From Poland it comes by truck.
@@MaximKachurovskiy I just checked it and it was substantially cheaper than the price you mentioned. Currently it's only €573,75. Oh sorry, I forgot to mention the shipping costs. That will be €1776,38 to have it shipped from China to the Netherlands.... So that's literally less than 1/4 for the actual lathe, and more than 3/4 for the shipping....
Lipstick on a pig! It's too bad that they make it look good but the internals not so much. Good job on cleaning it. You might need to do more work on it to get it to work better, but that's what you get with a low cost machine. The live center is wobbling a lot. Seems like it's not worth keeping? Good idea to put WD40 everywhere there is rust, hopefully that should stop it from getting worse.
Lots of people comment on these type of lathes that they are made inferior but it isnt my view. I think its great value and a good way to get started. I have the 180 version of this lathe and it i am enjoying it so far.
Sure, that's 0.794mm, use kachurovskiy.com/gears/ to calculate the required set of gears - or install an electronic lead screw to cut any thread - github.com/kachurovskiy/nanoels
Hi Leon, yes, it's a good lathe, working with steel is not a problem. I've shorted the main electronic control board and now waiting for the seller to offer one for sale (there's no listing for it) so spare parts might be a problem down the road.
этот сраный магаз работает через раз. мне нихера не пришел станок - продавец сказал что проблемы с таможней и предложил подождать до апреля 2021!!! - при заказе станка 11.11.2020. трэкался неделю, когда пересекал границу в районе п. Забайкальский (Чита) и .........
@@MaximKachurovskiy "в 6 раз больше информации на английском!"(С) Т.е. инфы на инглише уже больше, но мы будем упорно поддерживать неравенство? Ну тоже логика...... :)
@@13Chron мой канал существует для того чтобы радовать, общаться, находить единомышленников, помогать как можно большему числу людей. Ценность человека не зависит от гражданства и языка - поэтому для наиболее полной реализации моих целей канал на английском. Я бы сделал вторую аудио-дорожку на русском но RUclips пока не даёт мне доступ к этой функции.
![Megan Thee Stallion - Roc Steady (feat. Flo Milli) [Official Video]](http://i.ytimg.com/vi/HozPPyqW0dY/mqdefault.jpg)
well it's a lathe ruclips.net/user/postUgkxN9zrzkkhnjUF5PQbuA_B1gYdsfCu9k6z but it wasn't what i would have anticipated. Headstock, tailstock, carriage apron are manufactured from aluminum now not cast iron. The spindle diameter for the bearings is too small allowing for a few play in the spindle so I am using some blue Loctite to take out the play.
You mentioned 'totally dry, no oil or grease' several times. That's very unusual. I think you got a return. It didn't need to be broken, someone just didn't like it. Clue: the lathe manufacturer doesn't make chucks, they buy them built and already soaked in grease. That one was dry and rusty. It didn't leave either the chuck or lathe manufacturer that way.
Apparently selling returns is quite common and it should be the first thing to inspect for. I saw another youtuber's video and he also got a returned lathe sold as new, he asked for a partial refund since he decided to keep it anyway.
Just a tip; you tightened the belts up very tight... this is bad.
Aluminium pulleys have a large thermal expansion in use, and the toothed belts have tensile glass fibre reinforcement that does not stretch.
As a general rule, you should always run toothed belts loose enough so the belts can slide sideways on the pulleys, this allows some room for pulley expansion.
If the belts are tight the pulley expansion quickly destroys the glass fibres and the belts will break.
Thank you for this, it is very helpful to see a disassembly video.
a great video Maxim, thanks for your teardown, and review. I'd consider this lathe, but shipping to Canada is more than the cost of the lathe itself.
good luck. i have one of these. the roller bearings were not mounted correctly or the seats were not square which you could see in the uneven wear pattern. i re-seated them and adjusted the preload and the spindle handles parting much better. The other key mods i did were: remove the compound and make a solid tool post block, I used shims vs the set screws on the saddle and I had to machine a new gib because the one it shipped with could not be adjusted. Put your indicator on your tool and push down on it to see how much it can move down towards the ways. The tail stock was total garbage and needed lots of rework. The gears can't do many thread pitches because the banjo is not the right size. The charts for the gears in the manual were not for a 56 tooth spindle gear and did not work. I ended up just removing the gears and installing an electronic leadscrew. the machine cuts a taper and the headstock is not square to the ways, cut a long bar stout and measure the end diameters to see if yours is cutting a taper. My chucks are decent but it is strange they sent a 3 and 4 jaw self centering vs an independent 4 jaw. anyway... good luck.
ballistal? I use that on things and my fire arms here in the US!! my favorite!!
Thank for making this video! Nice video, Mr Maxim! I bought 1 of this lathe model VM210V also. But seems like the extra gear provided by the manufacturer to perform(cut) the metric screw thread operation on the lathe were not accurate on the pitch(I mean the gear ratio). Possible for you to share your English technical manual?(probably a link to download). Mine technical manual was given in Mandarin version, so have a hard time reading it. Thanks & appreciate in advance! Rdgs Stan😊
Sorry, I don't have the manual - but you can calculate the gears for the required pitch on kachurovskiy.com/pages/gear-calculator
I have a plan to buy that model and I wondering how good quality your video help me alot Thanks!
Just bought one on amazon not arrived yet but can't wait. Once you'd cleaned and greased or oiled the parts look great
Congrats! Can you post a link to the Amazon listing? There's a great variety of lathes sold under the WM210V model by many different manufacturers
Поздравляю с покупкой. У меня такой же станок он супер.
Q: Greetings Master, what is the maximum tool size that the stock toolpost accepts?
A: At 3:33 you reply to this, sorry: 10mm is the default toolpost
Q: What did you had to do be able to use the 12mm tools centered on the axis?
My dear friend, you can use 12mm tools with a 250-001 tool post (see AliExpress) - but I recommend using 20mm tools as per ruclips.net/video/2Hvbsx-P7fA/видео.html
Hi maxim, a question sir.
Did that lathe comes with the quick change toolpost? Thanks.
"I got it down to 2-hundrets..." This is the moment , where you face your chuck and indicate your spanning point. - because it makes a huge difference.
Just subscribed and I've been watching your videos most of the morning.
Nice family life you've got going on there.
I'm getting ready to buy my first metal lathe and I've narrowed down to the one you have and a couple others including the Grizzly G0765.
Are you happy overall with your purchase, and if you had it to do over would you buy the same model?
I really like what you did with all of the steppers and bearings for improved performance, which is why I'm considering going with the same so I can just follow in your footsteps.
Dave, I'm not really using my lathe for any practical purpose, just playing with some parts now and then - so no expert on the subject. This exact model has gotten more expensive since I bought it (especially the shipping), today I'd probably go for www.aliexpress.com/item/678185093.html instead - it appears incredibly similar but I can't guarantee that all the 3D models will fit it perfectly since I didn't try that. Best wishes!
@@MaximKachurovskiy Thanks Maxim, I just checked it out and it seems like the price is fine, but they want 750 to deliver to the U.S.
My gut keeps pushing me to buy the Grizzly because of their customer service.
Then again, I may buy one and get bored with it and then watch it collect dust.
Anyway, thanks for your help.
Bought also the same mini lathe from this saler begining of this year but haven't got time to really test it. Just made it run in box. Looks clean.
I am guilty of buying stuff I never use too 😃
@@MaximKachurovskiy Your video made me get back to it. Great I will soon!
Видимо у них разные критерии ОТК для СНГ и Запада. В том который приехал нам половина деталей вырублена топором. Включая контактирующие со станиной "плоскости" (именно в кавычках) каретки суппорта...
Странно, в отзывах на Али из России и Украины пишут примерно то же самое. Может, вы у другого продавца брали или немного другую модель?
Thank you, Great video. I just spent about a week looking at these little lathes and think this is the best one on Ali-express. After the last 3 years would you still recommend to buy this machine? I am a fitter/machinist so I'm capable of fine tuning and resolving issues. I just need something small in my shed for motorcycle and car parts and don't want to spend more than $1500AUD and this one is currently $1300.
This lathe is no longer available but similar ones are. They vary in quality. Check out Numobams brand, I believe they sell decent lathes unlike some other companies.
@@MaximKachurovskiy Is there a way to reverse the lead screw on this lathe for left hand thread cutting?
@@peatergriffin no - but don't pay for those cheap gearboxes, they are no use, just get an after-market electronic leadscrew. There are many including ones I offer on kachurovskiy.com/
@@MaximKachurovskiy Thank you very much. Yes I saw alot of bad reviews on that version. I think I found this same lathe from a seller called CNC QIYI TOOL Store. I appreciate the video and response.
You should invest in an ultrasonic cleaner. It would make the job of cleaning the grit and rust 1000x faster and cleaner. They are a lot cheaper than they used to be. I picked one up for about $100 on eBay and it has helped me our a lot.
Bob, I saw they need special filling too? Not sure I understand how they work exactly. Operations like these are rare at my shop and space is at a premium so I decided to skip on them for now.
@@MaximKachurovskiy Nope! No special liquids needed, just degreaser mixed with water. It depends on what you're cleaning. They come in all sizes, and are great for cleaning almost anything.
@@MaximKachurovskiy I love my ultrasonic cleaner, and they can be used for all sorts of things. The Thought Emporium made a video about artificially aging cheap alcohol by adding wood chips and running it in an ultrasonic bath.
Where did you buy your quick change tool post ? Did you have to machine the piece or did it fit right away ?
Great video ! Thanks
The 250-000 tool post and all the attachments for it are from AliExpress, too. It fits fine without any machining but the limit pin that you see sticking out from the plate on 8:28 makes it inconvenient to rotate the tool post which is not a super big deal because tool post is usually kept in place and not rotated often. What is more of a problem is that 250-000 tool post is small and flimsy i.e. it will vibrate under load and vibration breaks carbide cutters. There are some workarounds for this problem but maybe getting a slightly bigger/different tool post is a better idea 🤷
@@MaximKachurovskiy Maybe the 250-100 but it seems that this tool post needs some work to modify it. Also some have modified the compound by adding more screws to tighten it better:
fr.aliexpress.com/item/4001204070693.html?spm=a2g0s.8937460.0.0.7d802e0eiUtDv0
I wonder if this one could be any better than the 250-00:
fr.aliexpress.com/item/4000857204659.html?spm=a2g0w.12010612.8148356.21.447d4d6cLz8iKU
Nice setup work
Nice overview! If I noticed rightly, you were using Liqui Moly multi-purpose grease for all gears. What kind of oil you are using to lube all lube points and slide ways?
Thank you. I've switched to Nigrin www.amazon.de/Nigrin-74145-Mehrzweckfett-Tube-250/dp/B001BAU3VY for lithium grease because it has very little smell compared to Liqui Moly - and also easier to apply from the tube.
For oiling, I'm using the sliding oil I bought for the mill: www.amazon.de/gp/product/B01MZFZVPO - it almost entirely removes the "sticking" effect when a part starting moving after standing still for a while. It also has very little smell. Seems good for drilling and thread cutting too.
Hi,
schöne kleine Drehbank. Ich suche auch schon einige Zeit nach diesem speziellen Typ. Können Sie mir sagen wo ich diese Drehbank kaufen kann?
Vielen Dank.
Gruß
Hi @reneh4602, heutzutage ist der Versand von Drehmaschinen aus China sehr teuer, Angebote auf www.vevor.de/s/drehbank sind sinnvoll.
@@MaximKachurovskiy Danke für die schnelle Rückmeldung. Das habe ich mir schon gedacht. Die Maschinen von Vevor habe ich auch schon ins Auge gefasst. Wieviel KW hat Ihre Maschine? 750 Watt?
@@reneh4602 Die Wattangaben auf AliExpress werden normalerweise überbewertet. Ich weiß nicht genau, wie viel Watt mein Motor hat. 750W sollten ausreichen.
how do you like this lathe, one year later? I'm considering buying one to work mainly with plastics, but i do need to have good tolerances and would probably set it up with a DRO
It's a good lathe but you will have a lot of trouble fitting a DRO onto it, there's just isn't enough space, consider buying one with a DRO pre-installed.
I have a question something this item is good? i'm asking please answer answer me because i want to buy like this
Hi, yes, this is a good lathe. It's not perfect, with more money you can buy a much heavier lathe that will be much better but that's a different story.
I have the very similar machine,
How do you adjust the gears so it will sounds smooth ?
What lubricant is best for that gears ?
To adjust the gears, put a piece of paper between them, tighten the gear nut, then remove the paper. I used Nigrin lithium grease because it smells less than other greases. Cheers!
@@MaximKachurovskiy thanks man
how is this lathe is different then WM 180 from Warco?
У меня пoхожий станок, только с коробкой передачь на 3 скорости и переменой направления.
К сожалению на этом всё. Куда нос не сунь то дырки высверлены не туда то зазоры как крысинные норы.
Месяц только пытался понят как и что.
Кстати, спасибо за модифицации на thingyverse.
Good explanation...
How much did you pay for shipping to germany? Atm it's more than the machine's price unfortunately
Dominic, I paid 857€ total of which 264€ was delivery. Currently delivery is very expensive, this happened before, just check back in a few weeks. Cheers!
Thank you very much!
Привет, а точно в германию без таможенных расходов доставляют?
Я посмотрел твою оценку на али на этот станок, ты пишешь no customs.
Азиз, я ничего не доплачивал, привезли грузовиком из Польши. Шло очень долго :)
@@MaximKachurovskiy Привет. Сам буквально на кнопке заказа сижу. Думаю серый взять через ИБей, или может тоже такой взять. Как тебе станок твои? Может что посоветуешь. Я тоже в Германии живут.
Ты говоришь 850€. А там сейчас стоит где то 630€ станок и пересылка 790€. Это как?
@@werschkowdennis6533 опять подорожало видимо. Уже такое было несколько месяцев назад, в комментариях обсуждали. Подожди месяц, должно вернуться в норму. Дополнительные деньги таможня с меня не спросила. Серый говорят существенно хуже.
Gear calculator for this lathe: kachurovskiy.com/gears/
90€ Electronic Lead Screw for this lathe: ruclips.net/video/9uTdDk2EqG4/видео.html / github.com/kachurovskiy/nanoels
what is the good engine for stainless 304??
Привет. У меня новый 8x16 MX210V ,когда поварачиваешь ручку спид контроля, то станок начинает работать со 180 оборотов , если повернуть ручку на уменьшение то просто останавливаеться. ремен. стоит на малой передаче от 0 до 1250об. но на деле получаеться только от 180...?? случайно не знаешь в чём дело?? Спасибо.
Привет, я сам мало понимаю в этом деле как видишь но можно погадать. Попробуй гитару временно разомкнуть со шпинделем - может она стопорит на малых оборотах из-за трения шестерёнок.
@@MaximKachurovskiy Спасибо, сегодня попробую.
Попробуй уменьшить максимальное напряжение на плате контроля, там есть потенциометр с пометкой Vmax
@@graforlov1738 Спасибо, попробую.
@@novii68 и что в итоге помогло решить проблему?
Sehr angenehmes Video, dadurch, dass Sie ruhig sprechen und keine wilde Hintergrundmusik verwenden. Danke für Ihre Arbeit, auch für Electronic Lead Screw @ Github. Das und andere Videos von Ihnen werde ich mir demnächst zu Gemüte führen :-).
Very enjoyable video, in that you speak calmly and don't use wild background music. Thank you for your work, also for Electronic Lead Screw @ Github. I will have a look at that and other videos from you soon :-).
Рисковый ты парень... С тряпкой к токарному станку лезть... Сижу думаю. Стоит ли дальше смотреть
Вася, это бумажные салфетки, тряпок у меня в мастерской нет.
@@MaximKachurovskiy Ну по видео не видно что она бумажная. А тряпок нет зря. САТ овские полотенца очхороши что в рулоне что в коробке
Hello,
you say that you had the machine sent to Germany. Did you then have to pay additional import tax at the customs in Germany.
Averell, no, it just showed up at the door. This particular seller ships by ship from China to Poland and handles all the customs. From Poland it comes by truck.
@@MaximKachurovskiy That's not bad, but the seller now wants € 836.89 shipping to Germany. All together you would pay € 1.417,55.
@@averelldalton8997 that's weird, it goes up and down every day so might be a temporary glitch. Feel free to ask the seller, they reply quickly.
@@MaximKachurovskiy I just checked it and it was substantially cheaper than the price you mentioned. Currently it's only €573,75. Oh sorry, I forgot to mention the shipping costs. That will be €1776,38 to have it shipped from China to the Netherlands.... So that's literally less than 1/4 for the actual lathe, and more than 3/4 for the shipping....
@@pieterveenders9793 Yeah, not sure what's going on with shipping prices for this lathe lately.
I think this was a good video. :)
Bro i have a question something this is item is good? Because i want to buy like this machine
Ottimo lavoro è pulito 👍
Lipstick on a pig! It's too bad that they make it look good but the internals not so much. Good job on cleaning it. You might need to do more work on it to get it to work better, but that's what you get with a low cost machine. The live center is wobbling a lot. Seems like it's not worth keeping? Good idea to put WD40 everywhere there is rust, hopefully that should stop it from getting worse.
Ferno, I think it's a good deal for the money in this weight range in my region. I do keep it well oiled, thank you!
Lots of people comment on these type of lathes that they are made inferior but it isnt my view. I think its great value and a good way to get started. I have the 180 version of this lathe and it i am enjoying it so far.
Ein guter Anfang.
Can this machine be set up to do 32tpi?
Sure, that's 0.794mm, use kachurovskiy.com/gears/ to calculate the required set of gears - or install an electronic lead screw to cut any thread - github.com/kachurovskiy/nanoels
Hello Sir,
After 6 month, are you happy with this lathe? is it accurate for work steel parts?
Please excuse my bad english and thank you
Hi Leon, yes, it's a good lathe, working with steel is not a problem. I've shorted the main electronic control board and now waiting for the seller to offer one for sale (there's no listing for it) so spare parts might be a problem down the road.
@@MaximKachurovskiy Thank you very much for your answers : - )
Дыс ис видео из вэри гуд. Не хватает только транслэйт ту раша. Ай лайк)
Включите субтитры и перевод английского на русский, я так смотрю )
этот сраный магаз работает через раз. мне нихера не пришел станок - продавец сказал что проблемы с таможней и предложил подождать до апреля 2021!!! - при заказе станка 11.11.2020. трэкался неделю, когда пересекал границу в районе п. Забайкальский (Чита) и .........
Сочувствую. Раз пересекал границу то проблемы не с магазином а с желдорэкспедицией? Про них разные отзывы.
@@MaximKachurovskiy не, отправили типа поездом до Москвы, а с Москвы до Самары должна была доставить CSE, по ее сайту и трэкалась YH0111763455
Есть ли возможность сделать видео на руском
Даниил, попробуй пожалуйста субтитры с авто-переводом, если перевод совсем плохой то могу подправить!
Хули их слушать ихни балтавню,мне бы молча показали лучше и так поймешь
Гинеколог блин прям!!!!!!!!
Жаль что не по русскому языку.
Включайте субтитры и перевод на русский. Тут они есть.
дизлайк за вражеский язык)
Интересно, но пусть англичане подписываются, пока дизлайк
На английском говорят 1500 миллионов, на русском 265. На любую интересующую вас тему вы найдете в среднем в 6 раз больше информации на английском!
@@MaximKachurovskiy "в 6 раз больше информации на английском!"(С)
Т.е. инфы на инглише уже больше, но мы будем упорно поддерживать неравенство? Ну тоже логика...... :)
@@13Chron мой канал существует для того чтобы радовать, общаться, находить единомышленников, помогать как можно большему числу людей. Ценность человека не зависит от гражданства и языка - поэтому для наиболее полной реализации моих целей канал на английском. Я бы сделал вторую аудио-дорожку на русском но RUclips пока не даёт мне доступ к этой функции.