COMMERCIAL TIGHTNESS TEST pt2
HTML-код
- Опубликовано: 18 окт 2024
- Thanks for liking & subscribing if this video was helpful. Feel free to share your views in the comments. If you think this information could assist someone else share it. Check out the playlists below:
• Commercial gas enginee...
• Commercial tightness test
• Day in the life commer...
• BMS & Electric tests
• Day in the life of a p...
• Pumps
• Gas fired water heaters
• Work life balance & im...
• Forced draft burners
• Leaks
• Saving money
• RUclipsr/content creat...
• Phone apps and useful ...
• Van reviews
• Week in the life comme...
• First sites as a comme...
• Variety of HVAC/Buildi...
To send me a non public message:
commercialengineer@mail.com
Disclaimer:
This video is for qualified and competent commercial gas safe registered engineers only.
Do not take it as advice, do your own due diligence before carrying out any work.
Please ensure that you are gas safe registered and follow the current regulations.
Carry out your safety checks. Your Flues, Air, Gas, Safety device checks/ 26.9 checks.
Do an overall risk assessment and wear PPE when necessary.
Safe Isolation Procedure & electric safety:
Identify the source(s) of supply. Test your digital multimeter / approved voltage indicator & volt stick to make sure that it is working properly. Isolate the supply, disconnecting the system from the mains. Place the voltage free wires into a terminal block/wago. Secure or “lock off” the isolation using your safety padlock, preventing any tampering. Put do not use signs up on the switch you have isolated/locked off. It is good practice to wear gloves, rubber sole boots, have an electrical safety mat underneath you whilst working on high voltage and use VDE tools. Ensure that you are qualified & / or competent to work on high voltage.
Refer to your manufacturer instructions.
These videos have been made in good faith to encourage working standards, mindsets and knowledge in the industry.
Excellent work!
Thanks for watching. Have a good weekend
Nice video. Any chance of a copy of that service work sheet you used to help work out the gas pipework volume calculation. Cheers
Hi Lee, sure ping me an email to: commercialgasengineer@mail.com
@@CommercialGasEngineerVideos I also just dropped you email. It's a good idea with sheet like this👍
Very nice once again thank you mate
Thank you
@@HarryMasters-hd3pn thanks for watching
Lovely clips❤
Thanks
Nice one mate. Keep up the great work.
Keep up the good work on your youtube channel too.
@@CommercialGasEngineerVideos We have been a little bit over the last few weeks but we care getting back to 1 video a week now.
@@appsplumbingltd plumbers! Respect me ! Look upto me !
Did this video help, if not what's missing?
Great video. A couple of good videos that would be very useful would be testing and setting up riello forced draught burner and ventilation calculations for radiant tube heaters! Keep up the good work
I'll aim to do one on nu-way burners. The radiant tube heaters vid I'll leave to you.
No purge point beetween ecv and meter
have you noticed the gas meter volumes have all changed from the igem books, you had a u160 which you put down 0.304 but if you look on the meter its actually 0.048.
It's a U160. The bar code states what meter it is. 0.048 is the volume for a much smaller meter.
I actually came here to say the same 👍
If you look at the badge it tells you its 48 decimetres which is 0.048
@fidotbeddoe a few things say that this is a U160. First of all the Qmax. 2nd contacting the manufacturer who confirmed this. 3rd the bar code states what it is. Google "Gas meter Identification". Igem 1 helps with this.
@@mustafapolat2540 a few things say that this is a U160. First of all the Qmax. 2nd contacting the manufacturer who confirmed this. 3rd the bar code states what it is. Google "Gas meter Identification". Igem 1 helps with this.
Can't have butterfly AECV where it enters the building
Nice video , Can I have calculations sheet, please?
Thanks, sure send me an email. commercialgasengineer@mail.com
@@CommercialGasEngineerVideosthe email doesn't work. Is there a new one?
Hi
Where do you get that template for you calculations.
Thanks.
Send me an email and I'll get one over to you. commercialgasengineer@mail.com
Gas booster is a new one to me
Where can I find those sheets
Send over an email and I'll get one to you commercialengineer@mail.com
so sorry ive lost the email you sent with the template can you re send please.
Sent
would the ttp need to be higher than 21 as i thought ttp is op
I am still yet to see a gas booster set with flexis !/ Bellows! In all my day's
hi can i have your template please
Hi could you send me a pdf with the service sheet please if possible
Hi Harry,
Send me an email to:
commercialengineer@mail.com
And I'll get one over to ya.
Hi great videos learnt alot can i have your template please
Sent, I believe 👍
Condemned!
Thanks for watching
I have never seen a pump on gas!
Thanks for your comments
My favourite movie is the purge