There’s a drain screw underneath. The upper final drive screw is for filling. There is also no need to take off the cover. Find yourself a new mechanic or better yet, do it yourself. It literally takes 10 minutes to change the final drive fluid.
what are you doing? you don't have to take apart the driving system cover. Only you have to do is loosening the oil drain screw! now I see you are doing this to get more money. right?
this is the final drive oil. not the engine oil. so no oil filter. the final drive is more like transmition oil change, except you use 10w40 oil. The engine oil bolts are on the bottom and other side of bike.
official maintenance manual says 10w30. but most folks in the forums say 10w40. Just fill it up until it starts dripping out. dont forget to turn the wheel, that pulls the oil inside it. manual says it has 3.2 qt capacity, 3.1 liters, but really just fill it till it starts dripping out. tourque bolt to 9 lbs. and yes you can do this with the tuperware on, but it gets a bit messy and you might want to look at your belt anyway.
official maintenance manual says 10w30. but most folks in the forums say 10w40. Just fill it up until it starts dripping out. dont forget to turn the wheel, that pulls the oil inside it. tourque bolt to 9 lbs. and yes you can do this with the tuperware on, but it gets a bit messy and you might want to look at your belt anyway.
All that work to change the oil?!
There’s a drain screw underneath. The upper final drive screw is for filling. There is also no need to take off the cover. Find yourself a new mechanic or better yet, do it yourself. It literally takes 10 minutes to change the final drive fluid.
what are you doing? you don't have to take apart the driving system cover. Only you have to do is loosening the oil drain screw! now I see
you are doing this to get more money. right?
Him has gone over the Edge...
Shouldn''t be the oil filter be replaced in the same time??
this is the final drive oil. not the engine oil. so no oil filter. the final drive is more like transmition oil change, except you use 10w40 oil. The engine oil bolts are on the bottom and other side of bike.
What is the degree of viscosity in the finished oil? ⁉️👆@@Shaun-vy9vi
would it have killed you to put the phone sideways and hold it still better
Any friction modifier? 80W90?
This Oil change is not done by me but by the motorcycle workshop worker
Yes. Good question. How much?
XTruckteacher About 3 to 4 Ounces, I think.
@@Truckteacherits until the oil starts to get out, let it level out and close.
8 years later i hope you did it already 😂
fossi nel padrone non ti porterei la moto a manutenzionarla ,hai smontato mezza moto per cambiare l'olio agli ingranaggi
how much oil goes???
320 ml
official maintenance manual says 10w30. but most folks in the forums say 10w40. Just fill it up until it starts dripping out. dont forget to turn the wheel, that pulls the oil inside it. manual says it has 3.2 qt capacity, 3.1 liters, but really just fill it till it starts dripping out. tourque bolt to 9 lbs.
and yes you can do this with the tuperware on, but it gets a bit messy and you might want to look at your belt anyway.
@@Shaun-vy9vi can you give me an example of any oil available on the market Castrol/Shel etc ? Thanks
@@Shaun-vy9vi Here we talking about transmission oil man...in can t be 3.2 or 3.1 L .
Around 350ml . Same oil u use for the motor !!! Don t put gearbox oil !!!
What Grade oil ?
Royston Clark I use fully syn 10-50
official maintenance manual says 10w30. but most folks in the forums say 10w40. Just fill it up until it starts dripping out. dont forget to turn the wheel, that pulls the oil inside it. tourque bolt to 9 lbs.
and yes you can do this with the tuperware on, but it gets a bit messy and you might want to look at your belt anyway.
This guy has no clue what he is doing!
Looks a bit of a crows nest, all shit and twigs