Assalamu alaikum sir kya haal hai aap hai sar master control ke bare mein aap brief kar dete master control kya hai uske andar later ke bare mein samjha do
Sir we are using servo drive for robot movement....in auto mode robot work very well.... but in manual mode... we take up robot arm upward by pressing up botton in plc monitor but when we take out from up botton the robot arm moves downward due to gravity rather it should hold the position...... before it was holding the position ,it didn't come down side...due have any solution regarding this
There r 2 two possibilities for servo motor to change position at stop command 1st one is mechanical brake nd another one is electronic brake if u need to hold position at power failure u have to use mechanical brake with servo motor if u need to hold servo position at power on mode u have to on electronic brake to retain position in your situation cross check your program nd make sure electronic brake signal should on at desired position..
@@automationhouse8613 for not exceeding his limit,for example if we set limit 100 cm, servo motor run between 100 mm,not exceed to 100 mm,from homing station
Hello, could you tell me how I connect a CNC interface, the outputs are: +5 - DIR PUL my servo driver is SureServo AC Servo SVA-2100 only the connection of the pins and I know the programming. Thank you.
Brother very clear and knowledgeable lessons. I learn very much.
Very informative and well-explained.
Sir Kamal Boht khub sir... 👍👍👍
yar kia he baat hy aapki
i wanna be plc programmer like u... pray for me
Good luck bro👍
Great information sir
I am from Tamil Nadu. I don't understand Hindi even it's clear to understand.please next time write subtitles in English. Thanks
Ok dear
Nice sir thank you please keep it up
Nice 👍
Sir I used yaskawa 200v servo pack after setting all parameter, its showing an error of A. 0A. What about that?
Sir do inverter or do motar ek encoder or ek volume se kesy sink Karen gen ye bhi thora detail me bata den....???
Assalamu alaikum sir kya haal hai aap hai sar master control ke bare mein aap brief kar dete master control kya hai uske andar later ke bare mein samjha do
friend is healthy thanks for the help
Brother please batain k GX developer plc software kasy download karin.
Very good video
Thank you
Sir we are using servo drive for robot movement....in auto mode robot work very well.... but in manual mode... we take up robot arm upward by pressing up botton in plc monitor but when we take out from up botton the robot arm moves downward due to gravity rather it should hold the position...... before it was holding the position ,it didn't come down side...due have any solution regarding this
There r 2 two possibilities for servo motor to change position at stop command 1st one is mechanical brake nd another one is electronic brake if u need to hold position at power failure u have to use mechanical brake with servo motor if u need to hold servo position at power on mode u have to on electronic brake to retain position in your situation cross check your program nd make sure electronic brake signal should on at desired position..
sir please share playlist of Mitsubishi_PLC 🙏🙏🙏
Sir USB wire kaha se le
Do you have English version of this?
Sir, kenapa servo saya tidak bisa balik arah putaran, directionya on tapi tidak bisa merubah arah putaran
Iska next part kha par he
ruclips.net/video/AS9kmzfrRcg/видео.html
Sir, servo motor mai relay, contactor nahi lagata hai kya
Please elaborate
@@automationhouse8613 matab apne sirf driver motor or plc use kiya hai. Safety ke liye overload relay ya contactor nahi lagana padta hai kya
Ni kuch use ni kia built-in safeties hoti hin driver ki
@@automationhouse8613 ok
Servo ka jo pulse dega woh device ka kya naam hai?
PLC
Thanks sir for your explain, i'm sorry we want to ask. Is the wiring of output modul of plc is negatif common ?
Yes..PLC output is sink out type
@@automationhouse8613 thank you sir, i will try with old mitsubishi type.i'm from indonesian
Sir how I get position complete signal . Servo have a two position
U can use special data register that stores pulses value given by PLC.
Dear Sir, why i can't use DPLSY instruction for Gx Developer ? Please suggestion subtitution for DPLSY
U can use dplsy in gx
@@automationhouse8613 thank you sir, but i use mitsubishi A series type
servo motor homing pr video bnao bhai,or servo motor ki limit kaise set krte h???
Ok nd limit for what?
@@automationhouse8613 for not exceeding his limit,for example if we set limit 100 cm, servo motor run between 100 mm,not exceed to 100 mm,from homing station
Okay
Nice sir.
friend Healthy We want to connect the servo driver to plc delta ss2 yaskawa sgd7s
Follow more video i have explained how can connect and control
great sir
Sir make vedeo on servo home position increamental and absolute
Ok dear soon
@@automationhouse8613 thank you sir
Dear sir please updated speed control mode video
ruclips.net/video/WLvDacfzMTU/видео.html
Check above link i have already uploaded video on speed control mode.
Sir, could you able to help me to setup connection between PLC and Servo
Sure contact me on WhatsApp
If it is not difficult for you, please, give one more video to yaskawa plc delta.
Dear Contact me on Whatsapp...
@@automationhouse8613 if it's not difficult for you your phone number What to add on WhatsApp
@@amaneyekow5961 +923155368813
Thanks for help sir
Delta drive ac drive conection ASD-B0721-A. Where video
gsk ac servo motor and drive for drive with plc
Waiting for servo home logic by increamental encoder and absolute
Very nice
Amazing .
Great
Sir new video bnaye
Okay
Hello, could you tell me how I connect a CNC interface, the outputs are:
+5
-
DIR
PUL
my servo driver is SureServo AC Servo SVA-2100 only the connection of the pins and I know the programming.
Thank you.
Sir panasonic servo drive model. MFDKTB3A2CA1 pllse satting vido
helpful
nice sir` continue ` your whatsup
Thank you dear
Can you also whatsapp manual
download manual: drive.google.com/file/d/1on8DYEL9dqftepzT_aKcitRvOiV4vkdK/view
please help me
Hello sir Servo Motor collector program
Please elaborate or contact me on my WhatsApp
Y0 Y1 PULS
Sink out ia source out
Sir please
Yes?
É !!! YASKAWA !!! ROBÓTICS -
AUTOMAÇÃO - GLOBAL -
YASKAWA .