I have the exact same problem with my bird. After updating can't link to master. However my remote is set to master and I can turn it on or off. My remote isn't stuck. I tried re linking the bird and pushing the small link button on the inspire 1 which is located on the upper right side just inside of white body.Still won't link up. The pilot app says everything is up to date and normal. Yet the bird just flashes yellow light. I've tried e everything?......
hi you dont have a binding to the inspire sea the red licht in the kraft.....push te small butem with a pen 3sec down after it the led is green end fixt
Had the same exact problem, down to the exact details. I fixed mine, here's how. When the Remote Control is on, and your phone is connected, you should be able to click on the "No Signal, or Disconnected" red bar at the top of the screen. This will open up and should say you have an upgrade available. When I attempted to install this upgrade on my Samsung tablet and my Android HTC phone, it would simply not work, it would tell me something along the lines of "No internet connection" (despite being on Wifi). When I did it with a friend's Iphone 5s, however, it was able to install the upgrades. Once these upgrades were installed, it immediately reconnected to my Inspire 1. The problem was that the RC did not have the same firmware as the copter.
Syamsul Hazimee Husni There is a red button if you look on the right side of the drone in the nose there is a red button it is very small you will need a pen or a paper clip to reach go to the pair mode on the DJI go app press that then press and hold the red button on the drone. Look on internet pictures of the pair button on the drone
Hi, At 1,50 to 1,53 minutes of your video see and stop, I think your RC Settings ( you are on OFF ) press Master normaly after you will have signal ON Did you try outside also not inside your House ??? try Rgds, CV.
I tried to select master,but it remains in off mode. And I tried outside, in the park and at work, with no success. I only tape in the house cause it is freezing outside
1. get i-funbox for installing DJI Pilot app on your ios device: dl.i-funbox.com/de/ 2. download Pilot app: drive.google.com/file/d/0B8U9pDC2iKknTDBaZ2szOFJnOWs/view 3. Install the Pilot app on your device 4. Turn on everything according to dji inspire 1 usermanual 5. download and install the newest firmware from DJI on the inspire 1 and on the remote/s. (How to do it´s explained in the usermanual or in pdf includet at the download)
![[SOLVED] DJI Inspire 1 controller battery refurbish / replace](http://i.ytimg.com/vi/OX5OovXO0sA/mqdefault.jpg)
I have the exact same problem with my bird. After updating can't link to master. However my remote is set to master and I can turn it on or off. My remote isn't stuck. I tried re linking the bird and pushing the small link button on the inspire 1 which is located on the upper right side just inside of white body.Still won't link up. The pilot app says everything is up to date and normal. Yet the bird just flashes yellow light. I've tried e everything?......
+Tracy Simms you hit the button on the remote app then hit the button on the inspire that should work just wait till it pairs
+Matthewsw1234 hi
hi you dont have a binding to the inspire sea the red licht in the kraft.....push te small butem with a pen 3sec down
after it the led is green end fixt
Had the same exact problem, down to the exact details. I fixed mine, here's how. When the Remote Control is on, and your phone is connected, you should be able to click on the "No Signal, or Disconnected" red bar at the top of the screen. This will open up and should say you have an upgrade available. When I attempted to install this upgrade on my Samsung tablet and my Android HTC phone, it would simply not work, it would tell me something along the lines of "No internet connection" (despite being on Wifi). When I did it with a friend's Iphone 5s, however, it was able to install the upgrades. Once these upgrades were installed, it immediately reconnected to my Inspire 1.
The problem was that the RC did not have the same firmware as the copter.
i have the same problem does anyone fix this problem
hello friend I have the same problem with my INSPIRE1,
so far could you fix it?
Might you be so tell me how you did it,
thank you very much
hugs
+Leonid Temchuk you hit the button on the remote app then hit the button on the inspire that should work just wait till it pairs
+Matthewsw1234 can you do vido abut inspire
Bro have you fixed the problem I just had the same issue?
you hit the button on the remote app then hit the button on the inspire that should work just wait till it pairs
Matthew Wilkins can you explain in detail please..
Syamsul Hazimee Husni There is a red button if you look on the right side of the drone in the nose there is a red button it is very small you will need a pen or a paper clip to reach go to the pair mode on the DJI go app press that then press and hold the red button on the drone. Look on internet pictures of the pair button on the drone
Hi,
At 1,50 to 1,53 minutes of your video see and stop, I think your RC Settings ( you are on OFF ) press Master normaly after you will have signal ON
Did you try outside also not inside your House ??? try
Rgds, CV.
I tried to select master,but it remains in off mode. And I tried outside, in the park and at work, with no success. I only tape in the house cause it is freezing outside
Hands - On Music Ok, I will look at your 2nd answers, I had not seen a continuation your second video
1. get i-funbox for installing DJI Pilot app on your ios device: dl.i-funbox.com/de/
2. download Pilot app: drive.google.com/file/d/0B8U9pDC2iKknTDBaZ2szOFJnOWs/view
3. Install the Pilot app on your device
4. Turn on everything according to dji inspire 1 usermanual
5. download and install the newest firmware from DJI on the inspire 1 and on the remote/s. (How to do it´s explained in the usermanual or in pdf includet at the download)
forum.dji.com/forum.php?mod=viewthread&tid=5241&extra=page%3D1&lang=en